[pull] master from torvalds:master

Documentation/arm64/silicon-errata.rst

@@ -147,6 +147,14 @@ stable kernels.
 +----------------+-----------------+-----------------+-----------------------------+
 | Qualcomm Tech. | Falkor v{1,2}   | E1041           | QCOM_FALKOR_ERRATUM_1041    |
 +----------------+-----------------+-----------------+-----------------------------+
+| Qualcomm Tech. | Kryo4xx Gold    | N/A             | ARM64_ERRATUM_1463225       |
++----------------+-----------------+-----------------+-----------------------------+
+| Qualcomm Tech. | Kryo4xx Gold    | N/A             | ARM64_ERRATUM_1418040       |
++----------------+-----------------+-----------------+-----------------------------+
+| Qualcomm Tech. | Kryo4xx Silver  | N/A             | ARM64_ERRATUM_1530923       |
++----------------+-----------------+-----------------+-----------------------------+
+| Qualcomm Tech. | Kryo4xx Silver  | N/A             | ARM64_ERRATUM_1024718       |
++----------------+-----------------+-----------------+-----------------------------+
 +----------------+-----------------+-----------------+-----------------------------+
 | Fujitsu        | A64FX           | E#010001        | FUJITSU_ERRATUM_010001      |
 +----------------+-----------------+-----------------+-----------------------------+

Documentation/i2c/slave-eeprom-backend.rst

@@ -1,14 +1,26 @@
 ==============================
-Linux I2C slave eeprom backend
+Linux I2C slave EEPROM backend
 ==============================
 
-by Wolfram Sang <wsa@sang-engineering.com> in 2014-15
+by Wolfram Sang <wsa@sang-engineering.com> in 2014-20
 
-This is a proof-of-concept backend which acts like an EEPROM on the connected
-I2C bus. The memory contents can be modified from userspace via this file
-located in sysfs::
+This backend simulates an EEPROM on the connected I2C bus. Its memory contents
+can be accessed from userspace via this file located in sysfs::
 
 	/sys/bus/i2c/devices/<device-directory>/slave-eeprom
 
+The following types are available: 24c02, 24c32, 24c64, and 24c512. Read-only
+variants are also supported. The name needed for instantiating has the form
+'slave-<type>[ro]'. Examples follow:
+
+24c02, read/write, address 0x64:
+  # echo slave-24c02 0x1064 > /sys/bus/i2c/devices/i2c-1/new_device
+
+24c512, read-only, address 0x42:
+  # echo slave-24c512ro 0x1042 > /sys/bus/i2c/devices/i2c-1/new_device
+
+You can also preload data during boot if a device-property named
+'firmware-name' contains a valid filename (DT or ACPI only).
+
 As of 2015, Linux doesn't support poll on binary sysfs files, so there is no
 notification when another master changed the content.

arch/arm64/include/asm/alternative.h

@@ -73,11 +73,11 @@ static inline void apply_alternatives_module(void *start, size_t length) { }
 	".pushsection .altinstructions,\"a\"\n"				\
 	ALTINSTR_ENTRY(feature)						\
 	".popsection\n"							\
-	".pushsection .altinstr_replacement, \"a\"\n"			\
+	".subsection 1\n"						\
 	"663:\n\t"							\
 	newinstr "\n"							\
 	"664:\n\t"							\
-	".popsection\n\t"						\
+	".previous\n\t"							\
 	".org	. - (664b-663b) + (662b-661b)\n\t"			\
 	".org	. - (662b-661b) + (664b-663b)\n"			\
 	".endif\n"
@@ -117,9 +117,9 @@ static inline void apply_alternatives_module(void *start, size_t length) { }
 662:	.pushsection .altinstructions, "a"
 	altinstruction_entry 661b, 663f, \cap, 662b-661b, 664f-663f
 	.popsection
-	.pushsection .altinstr_replacement, "ax"
+	.subsection 1
 663:	\insn2
-664:	.popsection
+664:	.previous
 	.org	. - (664b-663b) + (662b-661b)
 	.org	. - (662b-661b) + (664b-663b)
 	.endif
@@ -160,7 +160,7 @@ static inline void apply_alternatives_module(void *start, size_t length) { }
 	.pushsection .altinstructions, "a"
 	altinstruction_entry 663f, 661f, \cap, 664f-663f, 662f-661f
 	.popsection
-	.pushsection .altinstr_replacement, "ax"
+	.subsection 1
 	.align 2	/* So GAS knows label 661 is suitably aligned */
 661:
 .endm
@@ -179,9 +179,9 @@ static inline void apply_alternatives_module(void *start, size_t length) { }
 .macro alternative_else
 662:
 	.if .Lasm_alt_mode==0
-	.pushsection .altinstr_replacement, "ax"
+	.subsection 1
 	.else
-	.popsection
+	.previous
 	.endif
 663:
 .endm
@@ -192,7 +192,7 @@ static inline void apply_alternatives_module(void *start, size_t length) { }
 .macro alternative_endif
 664:
 	.if .Lasm_alt_mode==0
-	.popsection
+	.previous
 	.endif
 	.org	. - (664b-663b) + (662b-661b)
 	.org	. - (662b-661b) + (664b-663b)

arch/arm64/include/asm/cputype.h

@@ -86,6 +86,7 @@
 #define QCOM_CPU_PART_FALKOR		0xC00
 #define QCOM_CPU_PART_KRYO		0x200
 #define QCOM_CPU_PART_KRYO_3XX_SILVER	0x803
+#define QCOM_CPU_PART_KRYO_4XX_GOLD	0x804
 #define QCOM_CPU_PART_KRYO_4XX_SILVER	0x805
 
 #define NVIDIA_CPU_PART_DENVER		0x003
@@ -114,6 +115,7 @@
 #define MIDR_QCOM_FALKOR MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_FALKOR)
 #define MIDR_QCOM_KRYO MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_KRYO)
 #define MIDR_QCOM_KRYO_3XX_SILVER MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_KRYO_3XX_SILVER)
+#define MIDR_QCOM_KRYO_4XX_GOLD MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_KRYO_4XX_GOLD)
 #define MIDR_QCOM_KRYO_4XX_SILVER MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_KRYO_4XX_SILVER)
 #define MIDR_NVIDIA_DENVER MIDR_CPU_MODEL(ARM_CPU_IMP_NVIDIA, NVIDIA_CPU_PART_DENVER)
 #define MIDR_NVIDIA_CARMEL MIDR_CPU_MODEL(ARM_CPU_IMP_NVIDIA, NVIDIA_CPU_PART_CARMEL)

arch/arm64/kernel/cpu_errata.c

@@ -472,12 +472,7 @@ static bool
 has_cortex_a76_erratum_1463225(const struct arm64_cpu_capabilities *entry,
 			       int scope)
 {
-	u32 midr = read_cpuid_id();
-	/* Cortex-A76 r0p0 - r3p1 */
-	struct midr_range range = MIDR_RANGE(MIDR_CORTEX_A76, 0, 0, 3, 1);
-
-	WARN_ON(scope != SCOPE_LOCAL_CPU || preemptible());
-	return is_midr_in_range(midr, &range) && is_kernel_in_hyp_mode();
+	return is_affected_midr_range_list(entry, scope) && is_kernel_in_hyp_mode();
 }
 #endif
 
@@ -728,6 +723,8 @@ static const struct midr_range erratum_1418040_list[] = {
 	MIDR_RANGE(MIDR_CORTEX_A76, 0, 0, 3, 1),
 	/* Neoverse-N1 r0p0 to r3p1 */
 	MIDR_RANGE(MIDR_NEOVERSE_N1, 0, 0, 3, 1),
+	/* Kryo4xx Gold (rcpe to rfpf) => (r0p0 to r3p1) */
+	MIDR_RANGE(MIDR_QCOM_KRYO_4XX_GOLD, 0xc, 0xe, 0xf, 0xf),
 	{},
 };
 #endif
@@ -772,11 +769,22 @@ static const struct midr_range erratum_speculative_at_list[] = {
 #ifdef CONFIG_ARM64_ERRATUM_1530923
 	/* Cortex A55 r0p0 to r2p0 */
 	MIDR_RANGE(MIDR_CORTEX_A55, 0, 0, 2, 0),
+	/* Kryo4xx Silver (rdpe => r1p0) */
+	MIDR_REV(MIDR_QCOM_KRYO_4XX_SILVER, 0xd, 0xe),
 #endif
 	{},
 };
 #endif
 
+#ifdef CONFIG_ARM64_ERRATUM_1463225
+static const struct midr_range erratum_1463225[] = {
+	/* Cortex-A76 r0p0 - r3p1 */
+	MIDR_RANGE(MIDR_CORTEX_A76, 0, 0, 3, 1),
+	/* Kryo4xx Gold (rcpe to rfpf) => (r0p0 to r3p1) */
+	MIDR_RANGE(MIDR_QCOM_KRYO_4XX_GOLD, 0xc, 0xe, 0xf, 0xf),
+};
+#endif
+
 const struct arm64_cpu_capabilities arm64_errata[] = {
 #ifdef CONFIG_ARM64_WORKAROUND_CLEAN_CACHE
 	{
@@ -916,6 +924,7 @@ const struct arm64_cpu_capabilities arm64_errata[] = {
 		.capability = ARM64_WORKAROUND_1463225,
 		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
 		.matches = has_cortex_a76_erratum_1463225,
+		.midr_range_list = erratum_1463225,
 	},
 #endif
 #ifdef CONFIG_CAVIUM_TX2_ERRATUM_219

arch/arm64/kernel/cpufeature.c

@@ -1408,6 +1408,8 @@ static bool cpu_has_broken_dbm(void)
 	static const struct midr_range cpus[] = {
 #ifdef CONFIG_ARM64_ERRATUM_1024718
 		MIDR_RANGE(MIDR_CORTEX_A55, 0, 0, 1, 0),  // A55 r0p0 -r1p0
+		/* Kryo4xx Silver (rdpe => r1p0) */
+		MIDR_REV(MIDR_QCOM_KRYO_4XX_SILVER, 0xd, 0xe),
 #endif
 		{},
 	};

arch/arm64/kernel/vmlinux.lds.S

@@ -165,9 +165,6 @@ SECTIONS
 		*(.altinstructions)
 		__alt_instructions_end = .;
 	}
-	.altinstr_replacement : {
-		*(.altinstr_replacement)
-	}
 
 	. = ALIGN(SEGMENT_ALIGN);
 	__inittext_end = .;

arch/mips/boot/dts/ingenic/gcw0.dts

@@ -92,7 +92,7 @@
 			"MIC1N", "Built-in Mic";
 		simple-audio-card,pin-switches = "Speaker", "Headphones";
 
-		simple-audio-card,hp-det-gpio = <&gpf 21 GPIO_ACTIVE_HIGH>;
+		simple-audio-card,hp-det-gpio = <&gpf 21 GPIO_ACTIVE_LOW>;
 		simple-audio-card,aux-devs = <&speaker_amp>, <&headphones_amp>;
 
 		simple-audio-card,bitclock-master = <&dai_codec>;

arch/mips/kernel/traps.c

@@ -723,12 +723,14 @@ static int simulate_loongson3_cpucfg(struct pt_regs *regs,
 		perf_sw_event(PERF_COUNT_SW_EMULATION_FAULTS, 1, regs, 0);
 
 		/* Do not emulate on unsupported core models. */
-		if (!loongson3_cpucfg_emulation_enabled(&current_cpu_data))
+		preempt_disable();
+		if (!loongson3_cpucfg_emulation_enabled(&current_cpu_data)) {
+			preempt_enable();
 			return -1;
-
+		}
 		regs->regs[rd] = loongson3_cpucfg_read_synthesized(
 			&current_cpu_data, sel);
-
+		preempt_enable();
 		return 0;
 	}
 
@@ -2169,6 +2171,7 @@ static void configure_status(void)
 
 	change_c0_status(ST0_CU|ST0_MX|ST0_RE|ST0_FR|ST0_BEV|ST0_TS|ST0_KX|ST0_SX|ST0_UX,
 			 status_set);
+	back_to_back_c0_hazard();
 }
 
 unsigned int hwrena;

arch/mips/lantiq/xway/sysctrl.c

@@ -514,8 +514,8 @@ void __init ltq_soc_init(void)
 		clkdev_add_pmu("1e10b308.eth", NULL, 0, 0, PMU_SWITCH |
 			       PMU_PPE_DP | PMU_PPE_TC);
 		clkdev_add_pmu("1da00000.usif", "NULL", 1, 0, PMU_USIF);
-		clkdev_add_pmu("1e108000.gswip", "gphy0", 0, 0, PMU_GPHY);
-		clkdev_add_pmu("1e108000.gswip", "gphy1", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.switch", "gphy0", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.switch", "gphy1", 0, 0, PMU_GPHY);
 		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
 		clkdev_add_pmu("1e116000.mei", "afe", 1, 2, PMU_ANALOG_DSL_AFE);
 		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);
@@ -538,8 +538,8 @@ void __init ltq_soc_init(void)
 				PMU_SWITCH | PMU_PPE_DPLUS | PMU_PPE_DPLUM |
 				PMU_PPE_EMA | PMU_PPE_TC | PMU_PPE_SLL01 |
 				PMU_PPE_QSB | PMU_PPE_TOP);
-		clkdev_add_pmu("1e108000.gswip", "gphy0", 0, 0, PMU_GPHY);
-		clkdev_add_pmu("1e108000.gswip", "gphy1", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.switch", "gphy0", 0, 0, PMU_GPHY);
+		clkdev_add_pmu("1e108000.switch", "gphy1", 0, 0, PMU_GPHY);
 		clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO);
 		clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU);
 		clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE);

arch/powerpc/mm/book3s64/pkeys.c

@@ -353,9 +353,6 @@ static bool pkey_access_permitted(int pkey, bool write, bool execute)
 	int pkey_shift;
 	u64 amr;
 
-	if (!is_pkey_enabled(pkey))
-		return true;
-
 	pkey_shift = pkeyshift(pkey);
 	if (execute && !(read_iamr() & (IAMR_EX_BIT << pkey_shift)))
 		return true;

block/bio-integrity.c

@@ -24,7 +24,8 @@ void blk_flush_integrity(void)
 	flush_workqueue(kintegrityd_wq);
 }
 
-void __bio_integrity_free(struct bio_set *bs, struct bio_integrity_payload *bip)
+static void __bio_integrity_free(struct bio_set *bs,
+				 struct bio_integrity_payload *bip)
 {
 	if (bs && mempool_initialized(&bs->bio_integrity_pool)) {
 		if (bip->bip_vec)

drivers/i2c/Kconfig

@@ -113,11 +113,18 @@ config I2C_STUB
 
 config I2C_SLAVE
 	bool "I2C slave support"
+	help
+	  This enables Linux to act as an I2C slave device. Note that your I2C
+	  bus master driver also needs to support this functionality. Please
+	  read Documentation/i2c/slave-interface.rst for further details.
 
 if I2C_SLAVE
 
 config I2C_SLAVE_EEPROM
 	tristate "I2C eeprom slave driver"
+	help
+	  This backend makes Linux behave like an I2C EEPROM. Please read
+	  Documentation/i2c/slave-eeprom-backend.rst for further details.
 
 endif
 

drivers/i2c/algos/i2c-algo-pca.c

@@ -314,7 +314,8 @@ static int pca_xfer(struct i2c_adapter *i2c_adap,
 			DEB2("BUS ERROR - SDA Stuck low\n");
 			pca_reset(adap);
 			goto out;
-		case 0x90: /* Bus error - SCL stuck low */
+		case 0x78: /* Bus error - SCL stuck low (PCA9665) */
+		case 0x90: /* Bus error - SCL stuck low (PCA9564) */
 			DEB2("BUS ERROR - SCL Stuck low\n");
 			pca_reset(adap);
 			goto out;

drivers/i2c/busses/i2c-designware-platdrv.c

@@ -12,6 +12,7 @@
 #include <linux/clk-provider.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
+#include <linux/dmi.h>
 #include <linux/err.h>
 #include <linux/errno.h>
 #include <linux/i2c.h>
@@ -191,6 +192,17 @@ static int dw_i2c_plat_request_regs(struct dw_i2c_dev *dev)
 	return ret;
 }
 
+static const struct dmi_system_id dw_i2c_hwmon_class_dmi[] = {
+	{
+		.ident = "Qtechnology QT5222",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Qtechnology"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "QT5222"),
+		},
+	},
+	{ } /* terminate list */
+};
+
 static int dw_i2c_plat_probe(struct platform_device *pdev)
 {
 	struct dw_i2c_platform_data *pdata = dev_get_platdata(&pdev->dev);
@@ -267,7 +279,8 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
 
 	adap = &dev->adapter;
 	adap->owner = THIS_MODULE;
-	adap->class = I2C_CLASS_DEPRECATED;
+	adap->class = dmi_check_system(dw_i2c_hwmon_class_dmi) ?
+					I2C_CLASS_HWMON : I2C_CLASS_DEPRECATED;
 	ACPI_COMPANION_SET(&adap->dev, ACPI_COMPANION(&pdev->dev));
 	adap->dev.of_node = pdev->dev.of_node;
 	adap->nr = -1;

drivers/i2c/busses/i2c-eg20t.c

@@ -180,6 +180,7 @@ static const struct pci_device_id pch_pcidev_id[] = {
 	{ PCI_VDEVICE(ROHM, PCI_DEVICE_ID_ML7831_I2C), 1, },
 	{0,}
 };
+MODULE_DEVICE_TABLE(pci, pch_pcidev_id);
 
 static irqreturn_t pch_i2c_handler(int irq, void *pData);
 

drivers/i2c/busses/i2c-mlxcpld.c

@@ -337,9 +337,9 @@ static int mlxcpld_i2c_wait_for_tc(struct mlxcpld_i2c_priv *priv)
 		if (priv->smbus_block && (val & MLXCPLD_I2C_SMBUS_BLK_BIT)) {
 			mlxcpld_i2c_read_comm(priv, MLXCPLD_LPCI2C_NUM_DAT_REG,
 					      &datalen, 1);
-			if (unlikely(datalen > (I2C_SMBUS_BLOCK_MAX + 1))) {
+			if (unlikely(datalen > I2C_SMBUS_BLOCK_MAX)) {
 				dev_err(priv->dev, "Incorrect smbus block read message len\n");
-				return -E2BIG;
+				return -EPROTO;
 			}
 		} else {
 			datalen = priv->xfer.data_len;