[pull] master from torvalds:master

Documentation/ABI/testing/sysfs-driver-ufs

@@ -916,21 +916,25 @@ Date:		September 2014
 Contact:	Subhash Jadavani <subhashj@codeaurora.org>
 Description:	This entry could be used to set or show the UFS device
 		runtime power management level. The current driver
-		implementation supports 6 levels with next target states:
+		implementation supports 7 levels with next target states:
 
 		==  ====================================================
-		0   an UFS device will stay active, an UIC link will
+		0   UFS device will stay active, UIC link will
 		    stay active
-		1   an UFS device will stay active, an UIC link will
+		1   UFS device will stay active, UIC link will
 		    hibernate
-		2   an UFS device will moved to sleep, an UIC link will
+		2   UFS device will be moved to sleep, UIC link will
 		    stay active
-		3   an UFS device will moved to sleep, an UIC link will
+		3   UFS device will be moved to sleep, UIC link will
 		    hibernate
-		4   an UFS device will be powered off, an UIC link will
+		4   UFS device will be powered off, UIC link will
 		    hibernate
-		5   an UFS device will be powered off, an UIC link will
+		5   UFS device will be powered off, UIC link will
 		    be powered off
+		6   UFS device will be moved to deep sleep, UIC link
+		    will be powered off. Note, deep sleep might not be
+		    supported in which case this value will not be
+		    accepted
 		==  ====================================================
 
 What:		/sys/bus/platform/drivers/ufshcd/*/rpm_target_dev_state
@@ -954,21 +958,25 @@ Date:		September 2014
 Contact:	Subhash Jadavani <subhashj@codeaurora.org>
 Description:	This entry could be used to set or show the UFS device
 		system power management level. The current driver
-		implementation supports 6 levels with next target states:
+		implementation supports 7 levels with next target states:
 
 		==  ====================================================
-		0   an UFS device will stay active, an UIC link will
+		0   UFS device will stay active, UIC link will
 		    stay active
-		1   an UFS device will stay active, an UIC link will
+		1   UFS device will stay active, UIC link will
 		    hibernate
-		2   an UFS device will moved to sleep, an UIC link will
+		2   UFS device will be moved to sleep, UIC link will
 		    stay active
-		3   an UFS device will moved to sleep, an UIC link will
+		3   UFS device will be moved to sleep, UIC link will
 		    hibernate
-		4   an UFS device will be powered off, an UIC link will
+		4   UFS device will be powered off, UIC link will
 		    hibernate
-		5   an UFS device will be powered off, an UIC link will
+		5   UFS device will be powered off, UIC link will
 		    be powered off
+		6   UFS device will be moved to deep sleep, UIC link
+		    will be powered off. Note, deep sleep might not be
+		    supported in which case this value will not be
+		    accepted
 		==  ====================================================
 
 What:		/sys/bus/platform/drivers/ufshcd/*/spm_target_dev_state

Documentation/dev-tools/kunit/usage.rst

@@ -522,6 +522,63 @@ There's more boilerplate involved, but it can:
   * E.g. if we wanted to also test ``sha256sum``, we could add a ``sha256``
     field and reuse ``cases``.
 
+* be converted to a "parameterized test", see below.
+
+Parameterized Testing
+~~~~~~~~~~~~~~~~~~~~~
+
+The table-driven testing pattern is common enough that KUnit has special
+support for it.
+
+Reusing the same ``cases`` array from above, we can write the test as a
+"parameterized test" with the following.
+
+.. code-block:: c
+
+	// This is copy-pasted from above.
+	struct sha1_test_case {
+		const char *str;
+		const char *sha1;
+	};
+	struct sha1_test_case cases[] = {
+		{
+			.str = "hello world",
+			.sha1 = "2aae6c35c94fcfb415dbe95f408b9ce91ee846ed",
+		},
+		{
+			.str = "hello world!",
+			.sha1 = "430ce34d020724ed75a196dfc2ad67c77772d169",
+		},
+	};
+
+	// Need a helper function to generate a name for each test case.
+	static void case_to_desc(const struct sha1_test_case *t, char *desc)
+	{
+		strcpy(desc, t->str);
+	}
+	// Creates `sha1_gen_params()` to iterate over `cases`.
+	KUNIT_ARRAY_PARAM(sha1, cases, case_to_desc);
+
+	// Looks no different from a normal test.
+	static void sha1_test(struct kunit *test)
+	{
+		// This function can just contain the body of the for-loop.
+		// The former `cases[i]` is accessible under test->param_value.
+		char out[40];
+		struct sha1_test_case *test_param = (struct sha1_test_case *)(test->param_value);
+
+		sha1sum(test_param->str, out);
+		KUNIT_EXPECT_STREQ_MSG(test, (char *)out, test_param->sha1,
+				      "sha1sum(%s)", test_param->str);
+	}
+
+	// Instead of KUNIT_CASE, we use KUNIT_CASE_PARAM and pass in the
+	// function declared by KUNIT_ARRAY_PARAM.
+	static struct kunit_case sha1_test_cases[] = {
+		KUNIT_CASE_PARAM(sha1_test, sha1_gen_params),
+		{}
+	};
+
 .. _kunit-on-non-uml:
 
 KUnit on non-UML architectures

drivers/i2c/busses/Kconfig

@@ -1013,6 +1013,7 @@ config I2C_SIRF
 config I2C_SPRD
 	tristate "Spreadtrum I2C interface"
 	depends on I2C=y && (ARCH_SPRD || COMPILE_TEST)
+	depends on COMMON_CLK
 	help
 	  If you say yes to this option, support will be included for the
 	  Spreadtrum I2C interface.

drivers/i2c/busses/i2c-imx.c

@@ -241,6 +241,19 @@ static struct imx_i2c_hwdata vf610_i2c_hwdata = {
 
 };
 
+static const struct platform_device_id imx_i2c_devtype[] = {
+	{
+		.name = "imx1-i2c",
+		.driver_data = (kernel_ulong_t)&imx1_i2c_hwdata,
+	}, {
+		.name = "imx21-i2c",
+		.driver_data = (kernel_ulong_t)&imx21_i2c_hwdata,
+	}, {
+		/* sentinel */
+	}
+};
+MODULE_DEVICE_TABLE(platform, imx_i2c_devtype);
+
 static const struct of_device_id i2c_imx_dt_ids[] = {
 	{ .compatible = "fsl,imx1-i2c", .data = &imx1_i2c_hwdata, },
 	{ .compatible = "fsl,imx21-i2c", .data = &imx21_i2c_hwdata, },
@@ -1330,7 +1343,11 @@ static int i2c_imx_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	match = device_get_match_data(&pdev->dev);
-	i2c_imx->hwdata = match;
+	if (match)
+		i2c_imx->hwdata = match;
+	else
+		i2c_imx->hwdata = (struct imx_i2c_hwdata *)
+				platform_get_device_id(pdev)->driver_data;
 
 	/* Setup i2c_imx driver structure */
 	strlcpy(i2c_imx->adapter.name, pdev->name, sizeof(i2c_imx->adapter.name));
@@ -1498,6 +1515,7 @@ static struct platform_driver i2c_imx_driver = {
 		.of_match_table = i2c_imx_dt_ids,
 		.acpi_match_table = i2c_imx_acpi_ids,
 	},
+	.id_table = imx_i2c_devtype,
 };
 
 static int __init i2c_adap_imx_init(void)

drivers/i2c/busses/i2c-octeon-core.c

@@ -347,7 +347,7 @@ static int octeon_i2c_read(struct octeon_i2c *i2c, int target,
 		if (result)
 			return result;
 		if (recv_len && i == 0) {
-			if (data[i] > I2C_SMBUS_BLOCK_MAX + 1)
+			if (data[i] > I2C_SMBUS_BLOCK_MAX)
 				return -EPROTO;
 			length += data[i];
 		}

drivers/i2c/busses/i2c-tegra-bpmp.c

@@ -80,7 +80,7 @@ static int tegra_bpmp_xlate_flags(u16 flags, u16 *out)
 		flags &= ~I2C_M_RECV_LEN;
 	}
 
-	return (flags != 0) ? -EINVAL : 0;
+	return 0;
 }
 
 /**

drivers/i2c/busses/i2c-tegra.c

@@ -326,6 +326,8 @@ static void i2c_writel(struct tegra_i2c_dev *i2c_dev, u32 val, unsigned int reg)
 	/* read back register to make sure that register writes completed */
 	if (reg != I2C_TX_FIFO)
 		readl_relaxed(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg));
+	else if (i2c_dev->is_vi)
+		readl_relaxed(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, I2C_INT_STATUS));
 }
 
 static u32 i2c_readl(struct tegra_i2c_dev *i2c_dev, unsigned int reg)
@@ -339,6 +341,21 @@ static void i2c_writesl(struct tegra_i2c_dev *i2c_dev, void *data,
 	writesl(i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg), data, len);
 }
 
+static void i2c_writesl_vi(struct tegra_i2c_dev *i2c_dev, void *data,
+			   unsigned int reg, unsigned int len)
+{
+	u32 *data32 = data;
+
+	/*
+	 * VI I2C controller has known hardware bug where writes get stuck
+	 * when immediate multiple writes happen to TX_FIFO register.
+	 * Recommended software work around is to read I2C register after
+	 * each write to TX_FIFO register to flush out the data.
+	 */
+	while (len--)
+		i2c_writel(i2c_dev, *data32++, reg);
+}
+
 static void i2c_readsl(struct tegra_i2c_dev *i2c_dev, void *data,
 		       unsigned int reg, unsigned int len)
 {
@@ -533,7 +550,7 @@ static int tegra_i2c_poll_register(struct tegra_i2c_dev *i2c_dev,
 	void __iomem *addr = i2c_dev->base + tegra_i2c_reg_addr(i2c_dev, reg);
 	u32 val;
 
-	if (!i2c_dev->atomic_mode)
+	if (!i2c_dev->atomic_mode && !in_irq())
 		return readl_relaxed_poll_timeout(addr, val, !(val & mask),
 						  delay_us, timeout_us);
 
@@ -811,7 +828,10 @@ static int tegra_i2c_fill_tx_fifo(struct tegra_i2c_dev *i2c_dev)
 		i2c_dev->msg_buf_remaining = buf_remaining;
 		i2c_dev->msg_buf = buf + words_to_transfer * BYTES_PER_FIFO_WORD;
 
-		i2c_writesl(i2c_dev, buf, I2C_TX_FIFO, words_to_transfer);
+		if (i2c_dev->is_vi)
+			i2c_writesl_vi(i2c_dev, buf, I2C_TX_FIFO, words_to_transfer);
+		else
+			i2c_writesl(i2c_dev, buf, I2C_TX_FIFO, words_to_transfer);
 
 		buf += words_to_transfer * BYTES_PER_FIFO_WORD;
 	}

drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c

@@ -1615,7 +1615,7 @@ static int gpmi_ecc_read_page_raw(struct nand_chip *chip, uint8_t *buf,
 	/* Extract interleaved payload data and ECC bits */
 	for (step = 0; step < nfc_geo->ecc_chunk_count; step++) {
 		if (buf)
-			nand_extract_bits(buf, step * eccsize, tmp_buf,
+			nand_extract_bits(buf, step * eccsize * 8, tmp_buf,
 					  src_bit_off, eccsize * 8);
 		src_bit_off += eccsize * 8;
 

drivers/mtd/nand/raw/intel-nand-controller.c

@@ -579,7 +579,7 @@ static int ebu_nand_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct ebu_nand_controller *ebu_host;
 	struct nand_chip *nand;
-	struct mtd_info *mtd = NULL;
+	struct mtd_info *mtd;
 	struct resource *res;
 	char *resname;
 	int ret;
@@ -647,12 +647,13 @@ static int ebu_nand_probe(struct platform_device *pdev)
 	       ebu_host->ebu + EBU_ADDR_SEL(cs));
 
 	nand_set_flash_node(&ebu_host->chip, dev->of_node);
+
+	mtd = nand_to_mtd(&ebu_host->chip);
 	if (!mtd->name) {
 		dev_err(ebu_host->dev, "NAND label property is mandatory\n");
 		return -EINVAL;
 	}
 
-	mtd = nand_to_mtd(&ebu_host->chip);
 	mtd->dev.parent = dev;
 	ebu_host->dev = dev;
 

drivers/mtd/nand/raw/nandsim.c

@@ -2210,6 +2210,9 @@ static int ns_attach_chip(struct nand_chip *chip)
 {
 	unsigned int eccsteps, eccbytes;
 
+	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
+	chip->ecc.algo = bch ? NAND_ECC_ALGO_BCH : NAND_ECC_ALGO_HAMMING;
+
 	if (!bch)
 		return 0;
 
@@ -2233,8 +2236,6 @@ static int ns_attach_chip(struct nand_chip *chip)
 		return -EINVAL;
 	}
 
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-	chip->ecc.algo = NAND_ECC_ALGO_BCH;
 	chip->ecc.size = 512;
 	chip->ecc.strength = bch;
 	chip->ecc.bytes = eccbytes;
@@ -2273,8 +2274,6 @@ static int __init ns_init_module(void)
 	nsmtd       = nand_to_mtd(chip);
 	nand_set_controller_data(chip, (void *)ns);
 
-	chip->ecc.engine_type = NAND_ECC_ENGINE_TYPE_SOFT;
-	chip->ecc.algo   = NAND_ECC_ALGO_HAMMING;
 	/* The NAND_SKIP_BBTSCAN option is necessary for 'overridesize' */
 	/* and 'badblocks' parameters to work */
 	chip->options   |= NAND_SKIP_BBTSCAN;

drivers/mtd/nand/raw/omap2.c

@@ -15,6 +15,7 @@
 #include <linux/jiffies.h>
 #include <linux/sched.h>
 #include <linux/mtd/mtd.h>
+#include <linux/mtd/nand-ecc-sw-bch.h>
 #include <linux/mtd/rawnand.h>
 #include <linux/mtd/partitions.h>
 #include <linux/omap-dma.h>
@@ -1866,26 +1867,28 @@ static const struct mtd_ooblayout_ops omap_ooblayout_ops = {
 static int omap_sw_ooblayout_ecc(struct mtd_info *mtd, int section,
 				 struct mtd_oob_region *oobregion)
 {
-	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct nand_device *nand = mtd_to_nanddev(mtd);
+	const struct nand_ecc_sw_bch_conf *engine_conf = nand->ecc.ctx.priv;
 	int off = BADBLOCK_MARKER_LENGTH;
 
-	if (section >= chip->ecc.steps)
+	if (section >= engine_conf->nsteps)
 		return -ERANGE;
 
 	/*
 	 * When SW correction is employed, one OMAP specific marker byte is
 	 * reserved after each ECC step.
 	 */
-	oobregion->offset = off + (section * (chip->ecc.bytes + 1));
-	oobregion->length = chip->ecc.bytes;
+	oobregion->offset = off + (section * (engine_conf->code_size + 1));
+	oobregion->length = engine_conf->code_size;
 
 	return 0;
 }
 
 static int omap_sw_ooblayout_free(struct mtd_info *mtd, int section,
 				  struct mtd_oob_region *oobregion)
 {
-	struct nand_chip *chip = mtd_to_nand(mtd);
+	struct nand_device *nand = mtd_to_nanddev(mtd);
+	const struct nand_ecc_sw_bch_conf *engine_conf = nand->ecc.ctx.priv;
 	int off = BADBLOCK_MARKER_LENGTH;
 
 	if (section)
@@ -1895,7 +1898,7 @@ static int omap_sw_ooblayout_free(struct mtd_info *mtd, int section,
 	 * When SW correction is employed, one OMAP specific marker byte is
 	 * reserved after each ECC step.
 	 */
-	off += ((chip->ecc.bytes + 1) * chip->ecc.steps);
+	off += ((engine_conf->code_size + 1) * engine_conf->nsteps);
 	if (off >= mtd->oobsize)
 		return -ERANGE;
 

drivers/mtd/nand/spi/core.c

@@ -343,6 +343,7 @@ static int spinand_read_from_cache_op(struct spinand_device *spinand,
 				      const struct nand_page_io_req *req)
 {
 	struct nand_device *nand = spinand_to_nand(spinand);
+	struct mtd_info *mtd = spinand_to_mtd(spinand);
 	struct spi_mem_dirmap_desc *rdesc;
 	unsigned int nbytes = 0;
 	void *buf = NULL;
@@ -382,9 +383,16 @@ static int spinand_read_from_cache_op(struct spinand_device *spinand,
 		memcpy(req->databuf.in, spinand->databuf + req->dataoffs,
 		       req->datalen);
 
-	if (req->ooblen)
-		memcpy(req->oobbuf.in, spinand->oobbuf + req->ooboffs,
-		       req->ooblen);
+	if (req->ooblen) {
+		if (req->mode == MTD_OPS_AUTO_OOB)
+			mtd_ooblayout_get_databytes(mtd, req->oobbuf.in,
+						    spinand->oobbuf,
+						    req->ooboffs,
+						    req->ooblen);
+		else
+			memcpy(req->oobbuf.in, spinand->oobbuf + req->ooboffs,
+			       req->ooblen);
+	}
 
 	return 0;
 }