Updated the latest messages to be in sync with grbl v1.1e

Changed version number to 0.9.8

Sender.py

@@ -103,7 +103,7 @@
 
 	"error:1"  : _("G-code words consist of a letter and a value. Letter was not found."),
 	"error:2"  : _("Numeric value format is not valid or missing an expected value."),
-	"error:3"  : _("Grbl '$' system command was not recognized or supported"),
+	"error:3"  : _("Grbl '$' system command was not recognized or supported."),
 	"error:4"  : _("Negative value received for an expected positive value."),
 	"error:5"  : _("Homing cycle is not enabled via settings."),
 	"error:6"  : _("Minimum step pulse time must be greater than 3usec"),
@@ -112,7 +112,7 @@
 	"error:9"  : _("G-code locked out during alarm or jog state"),
 	"error:10" : _("Soft limits cannot be enabled without homing also enabled."),
 	"error:11" : _("Max characters per line exceeded. Line was not processed and executed."),
-	"error:12" : _("Grbl '$' setting value exceeds the maximum step rate supported."),
+	"error:12" : _("(Compile Option) Grbl '$' setting value exceeds the maximum step rate supported."),
 	"error:13" : _("Safety door detected as opened and door state initiated."),
 	"error:14" : _("(Grbl-Mega Only) Build info or startup line exceeded EEPROM line length limit."),
 	"error:15" : _("Jog target exceeds machine travel. Command ignored."),
@@ -121,30 +121,31 @@
 	"error:21" : _("More than one g-code command from same modal group found in block."),
 	"error:22" : _("Feed rate has not yet been set or is undefined."),
 	"error:23" : _("G-code command in block requires an integer value."),
-	"error:24" : _("More than one g-code command that requires axis words found in block."),
-	"error:25" : _("Repeated g-code word found in block."),
-	"error:26" : _("No axis words found in block for g-code command or mode which requires them."),
-	"error:27" : _("Line number value is invalid"),
-	"error:28" : _("G-code command is missing a required value word."),
-	"error:29" : _("Work coordinate system commanded not supported."),
-	"error:30" : _("G53 only allowed during G0 and G1 motion modes."),
-	"error:31" : _("Axis words found in block while no command uses them."),
-	"error:32" : _("G2/3 arcs require at least one in-plane axis word."),
-	"error:33" : _("Motion command target is invalid."),
-	"error:34" : _("Arc radius value is invalid."),
-	"error:35" : _("G2/3 arcs require at least one in-plane offset word."),
-	"error:36" : _("Unused value words found in block."),
-	"error:37" : _("G43.1 dynamic tool length offset assigned to wrong axis."),
-
-	"ALARM:1" : _("Hard limit has been triggered. Machine position is likely lost due to sudden stop. Re-homing is highly recommended. `"),
+	"error:24" : _("Two G-code commands that both require the use of the XYZ axis words were detected in the block."),
+	"error:25" : _("A G-code word was repeated in the block."),
+	"error:26" : _("A G-code command implicitly or explicitly requires XYZ axis words in the block, but none were detected."),
+	"error:27" : _("N line number value is not within the valid range of 1 - 9,999,999."),
+	"error:28" : _("A G-code command was sent, but is missing some required P or L value words in the line."),
+	"error:29" : _("Grbl supports six work coordinate systems G54-G59. G59.1, G59.2, and G59.3 are not supported."),
+	"error:30" : _("The G53 G-code command requires either a G0 seek or G1 feed motion mode to be active. A different motion was active."),
+	"error:31" : _("There are unused axis words in the block and G80 motion mode cancel is active."),
+	"error:32" : _("A G2 or G3 arc was commanded but there are no XYZ axis words in the selected plane to trace the arc."),
+	"error:33" : _("The motion command has an invalid target. G2, G3, and G38.2 generates this error, if the arc is impossible to generate or if the probe target is the current position."),
+	"error:34" : _("A G2 or G3 arc, traced with the radius definition, had a mathematical error when computing the arc geometry. Try either breaking up the arc into semi-circles or quadrants, or redefine them with the arc offset definition."),
+	"error:35" : _("A G2 or G3 arc, traced with the offset definition, is missing the IJK offset word in the selected plane to trace the arc."),
+	"error:36" : _("There are unused, leftover G-code words that aren't used by any command in the block."),
+	"error:37" : _("The G43.1 dynamic tool length offset command cannot apply an offset to an axis other than its configured axis. The Grbl default axis is the Z-axis."),
+	"error:38" : _("An invalid tool number sent to the parser"),
+
+	"ALARM:1" : _("Hard limit triggered. Machine position is likely lost due to sudden and immediate halt. Re-homing is highly recommended."),
 	"ALARM:2" : _("G-code motion target exceeds machine travel. Machine position safely retained. Alarm may be unlocked."),
 	"ALARM:3" : _("Reset while in motion. Grbl cannot guarantee position. Lost steps are likely. Re-homing is highly recommended."),
-	"ALARM:4" : _("If probe is not in the expected initial state before starting probe cycle, where G38.2 and G38.3 is not triggered and G38.4 and G38.5 is triggered."),
-	"ALARM:5" : _("If the probe fails to contact the workpiece within the programmed travel for G38.2 and G38.4."),
-	"ALARM:6" : _("If the active homing cycle was reset."),
-	"ALARM:7" : _("If the safety door was opened during homing cycle."),
-	"ALARM:8" : _("Pull off travel failed to clear limit switch. Try increasing pull-off setting or check wiring."),
-	"ALARM:9" : _("Failed to find limit switch within travel. Defined as 1.5 * max_travel on search and 5 * pulloff on locate phases."),
+	"ALARM:4" : _("Probe fail. The probe is not in the expected initial state before starting probe cycle, where G38.2 and G38.3 is not triggered and G38.4 and G38.5 is triggered."),
+	"ALARM:5" : _("Probe fail. Probe did not contact the workpiece within the programmed travel for G38.2 and G38.4."),
+	"ALARM:6" : _("Homing fail. Reset during active homing cycle."),
+	"ALARM:7" : _("Homing fail. Safety door was opened during active homing cycle."),
+	"ALARM:8" : _("Homing fail. Cycle failed to clear limit switch when pulling off. Try increasing pull-off setting or check wiring."),
+	"ALARM:9" : _("Homing fail. Could not find limit switch within search distance. Defined as 1.5 * max_travel on search and 5 * pulloff on locate phases."),
 
 	"Hold:0" : _("Hold complete. Ready to resume."),
 	"Hold:1" : _("Hold in-progress. Reset will throw an alarm."),

bCNC.py

@@ -5,8 +5,8 @@
 # Author: vvlachoudis@gmail.com
 # Date: 24-Aug-2014
 
-__version__ = "0.9.7"
-__date__    = "3 Nov 2016"
+__version__ = "0.9.8"
+__date__    = "15 Jan 2017"
 __author__  = "Vasilis Vlachoudis"
 __email__   = "vvlachoudis@gmail.com"