sh: Add support for AP-SH4A-3A board.

This adds preliminary support for the alpha project AP-SH4A-3A reference
platform (SH7785 based).

Additional paltform information available at:

	http://www.apnet.co.jp/product/superh/ap-sh4a-3a.html

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

arch/sh/boards/Kconfig

@@ -323,6 +323,13 @@ config SH_SH2007
 	  Compact Flash socket, two serial ports and PC-104 bus.
 	  More information at <http://sh2000.sh-linux.org>.
 
+config SH_APSH4A3A
+	bool "AP-SH4A-3A"
+	select SH_ALPHA_BOARD
+	depends on CPU_SUBTYPE_SH7785
+	help
+	  Select AP-SH4A-3A if configuring for an ALPHAPROJECT AP-SH4A-3A.
+
 endmenu
 
 source "arch/sh/boards/mach-r2d/Kconfig"

arch/sh/boards/Makefile

@@ -13,3 +13,4 @@ obj-$(CONFIG_SH_ESPT)		+= board-espt.o
 obj-$(CONFIG_SH_POLARIS)	+= board-polaris.o
 obj-$(CONFIG_SH_TITAN)		+= board-titan.o
 obj-$(CONFIG_SH_SH7757LCR)	+= board-sh7757lcr.o
+obj-$(CONFIG_SH_APSH4A3A)	+= board-apsh4a3a.o

arch/sh/boards/board-apsh4a3a.c

@@ -0,0 +1,175 @@
+/*
+ * ALPHAPROJECT AP-SH4A-3A Support.
+ *
+ * Copyright (C) 2010 ALPHAPROJECT Co.,Ltd.
+ * Copyright (C) 2008  Yoshihiro Shimoda
+ * Copyright (C) 2009  Paul Mundt
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/mtd/physmap.h>
+#include <linux/smsc911x.h>
+#include <linux/irq.h>
+#include <linux/clk.h>
+#include <asm/machvec.h>
+#include <asm/sizes.h>
+#include <asm/clock.h>
+
+static struct mtd_partition nor_flash_partitions[] = {
+	{
+		.name		= "loader",
+		.offset		= 0x00000000,
+		.size		= 512 * 1024,
+	},
+	{
+		.name		= "bootenv",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 512 * 1024,
+	},
+	{
+		.name		= "kernel",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 4 * 1024 * 1024,
+	},
+	{
+		.name		= "data",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data nor_flash_data = {
+	.width		= 4,
+	.parts		= nor_flash_partitions,
+	.nr_parts	= ARRAY_SIZE(nor_flash_partitions),
+};
+
+static struct resource nor_flash_resources[] = {
+	[0]	= {
+		.start	= 0x00000000,
+		.end	= 0x01000000 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device nor_flash_device = {
+	.name		= "physmap-flash",
+	.dev		= {
+		.platform_data	= &nor_flash_data,
+	},
+	.num_resources	= ARRAY_SIZE(nor_flash_resources),
+	.resource	= nor_flash_resources,
+};
+
+static struct resource smsc911x_resources[] = {
+	[0] = {
+		.name		= "smsc911x-memory",
+		.start		= 0xA4000000,
+		.end		= 0xA4000000 + SZ_256 - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+	[1] = {
+		.name		= "smsc911x-irq",
+		.start		= evt2irq(0x200),
+		.end		= evt2irq(0x200),
+		.flags		= IORESOURCE_IRQ,
+	},
+};
+
+static struct smsc911x_platform_config smsc911x_config = {
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+	.flags		= SMSC911X_USE_16BIT,
+	.phy_interface	= PHY_INTERFACE_MODE_MII,
+};
+
+static struct platform_device smsc911x_device = {
+	.name		= "smsc911x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(smsc911x_resources),
+	.resource	= smsc911x_resources,
+	.dev = {
+		.platform_data = &smsc911x_config,
+	},
+};
+
+static struct platform_device *apsh4a3a_devices[] __initdata = {
+	&nor_flash_device,
+	&smsc911x_device,
+};
+
+static int __init apsh4a3a_devices_setup(void)
+{
+	return platform_add_devices(apsh4a3a_devices,
+				    ARRAY_SIZE(apsh4a3a_devices));
+}
+device_initcall(apsh4a3a_devices_setup);
+
+static int apsh4a3a_clk_init(void)
+{
+	struct clk *clk;
+	int ret;
+
+	clk = clk_get(NULL, "extal");
+	if (!clk || IS_ERR(clk))
+		return PTR_ERR(clk);
+	ret = clk_set_rate(clk, 33333000);
+	clk_put(clk);
+
+	return ret;
+}
+
+/* Initialize the board */
+static void __init apsh4a3a_setup(char **cmdline_p)
+{
+	printk(KERN_INFO "Alpha Project AP-SH4A-3A support:\n");
+}
+
+static void __init apsh4a3a_init_irq(void)
+{
+	plat_irq_setup_pins(IRQ_MODE_IRQ7654);
+}
+
+/* Return the board specific boot mode pin configuration */
+static int apsh4a3a_mode_pins(void)
+{
+	int value = 0;
+
+	/* These are the factory default settings of SW1 and SW2.
+	 * If you change these dip switches then you will need to
+	 * adjust the values below as well.
+	 */
+	value &= ~MODE_PIN0;  /* Clock Mode 16 */
+	value &= ~MODE_PIN1;
+	value &= ~MODE_PIN2;
+	value &= ~MODE_PIN3;
+	value |=  MODE_PIN4;
+	value &= ~MODE_PIN5;  /* 16-bit Area0 bus width */
+	value |=  MODE_PIN6;  /* Area 0 SRAM interface */
+	value |=  MODE_PIN7;
+	value |=  MODE_PIN8;  /* Little Endian */
+	value |=  MODE_PIN9;  /* Master Mode */
+	value |=  MODE_PIN10; /* Crystal resonator */
+	value |=  MODE_PIN11; /* Display Unit */
+	value |=  MODE_PIN12;
+	value &= ~MODE_PIN13; /* 29-bit address mode */
+	value |=  MODE_PIN14; /* No PLL step-up */
+
+	return value;
+}
+
+/*
+ * The Machine Vector
+ */
+static struct sh_machine_vector mv_apsh4a3a __initmv = {
+	.mv_name		= "AP-SH4A-3A",
+	.mv_setup		= apsh4a3a_setup,
+	.mv_clk_init		= apsh4a3a_clk_init,
+	.mv_init_irq		= apsh4a3a_init_irq,
+	.mv_mode_pins		= apsh4a3a_mode_pins,
+};

arch/sh/configs/apsh4a3a_defconfig

@@ -0,0 +1,102 @@
+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_SYSFS_DEPRECATED=y
+CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_SLAB=y
+CONFIG_PROFILING=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_CPU_SUBTYPE_SH7785=y
+CONFIG_MEMORY_START=0x0C000000
+CONFIG_FLATMEM_MANUAL=y
+CONFIG_SH_STORE_QUEUES=y
+CONFIG_SH_APSH4A3A=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_KEXEC=y
+CONFIG_PREEMPT=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_LRO is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_FW_LOADER is not set
+CONFIG_MTD=y
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_CFI=y
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_PHYSMAP=y
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_NETDEVICES=y
+CONFIG_NET_ETHERNET=y
+CONFIG_SMSC911X=y
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_SERIAL_SH_SCI=y
+CONFIG_SERIAL_SH_SCI_NR_UARTS=6
+CONFIG_SERIAL_SH_SCI_CONSOLE=y
+CONFIG_HW_RANDOM=y
+# CONFIG_HWMON is not set
+CONFIG_FB=y
+CONFIG_FB_SH7785FB=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_LOGO=y
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+CONFIG_EXT2_FS=y
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_NTFS_FS=y
+CONFIG_NTFS_RW=y
+CONFIG_PROC_KCORE=y
+CONFIG_TMPFS=y
+CONFIG_JFFS2_FS=y
+CONFIG_CRAMFS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V4=y
+CONFIG_CIFS=y
+CONFIG_NLS_DEFAULT="utf8"
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_CODEPAGE_932=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO=y
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_FTRACE is not set
+# CONFIG_CRYPTO_ANSI_CPRNG is not set
+# CONFIG_CRYPTO_HW is not set

arch/sh/tools/mach-types

@@ -62,3 +62,4 @@ ESPT			SH_ESPT
 POLARIS			SH_POLARIS
 KFR2R09			SH_KFR2R09
 ECOVEC			SH_ECOVEC
+APSH4A3A		SH_APSH4A3A