Merge branches 'x86/amd', 'x86/vt-d', 'arm/exynos', 'arm/mediatek', '…

…arm/msm', 'arm/rockchip', 'arm/smmu' and 'core' into next

Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt

@@ -1,6 +1,6 @@
 * ARM SMMUv3 Architecture Implementation
 
-The SMMUv3 architecture is a significant deparature from previous
+The SMMUv3 architecture is a significant departure from previous
 revisions, replacing the MMIO register interface with in-memory command
 and event queues and adding support for the ATS and PRI components of
 the PCIe specification.

Documentation/devicetree/bindings/iommu/mediatek,iommu.txt

@@ -1,7 +1,9 @@
 * Mediatek IOMMU Architecture Implementation
 
-  Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U) which
-uses the ARM Short-Descriptor translation table format for address translation.
+  Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U), and
+this M4U have two generations of HW architecture. Generation one uses flat
+pagetable, and only supports 4K size page mapping. Generation two uses the
+ARM Short-Descriptor translation table format for address translation.
 
   About the M4U Hardware Block Diagram, please check below:
 
@@ -36,7 +38,9 @@ in each larb. Take a example, There are many ports like MC, PP, VLD in the
 video decode local arbiter, all these ports are according to the video HW.
 
 Required properties:
-- compatible : must be "mediatek,mt8173-m4u".
+- compatible : must be one of the following string:
+	"mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW.
+	"mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW.
 - reg : m4u register base and size.
 - interrupts : the interrupt of m4u.
 - clocks : must contain one entry for each clock-names.
@@ -46,7 +50,8 @@ Required properties:
 	according to the local arbiter index, like larb0, larb1, larb2...
 - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW.
 	Specifies the mtk_m4u_id as defined in
-	dt-binding/memory/mt8173-larb-port.h.
+	dt-binding/memory/mt2701-larb-port.h for mt2701 and
+	dt-binding/memory/mt8173-larb-port.h for mt8173
 
 Example:
 	iommu: iommu@10205000 {

Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt

@@ -0,0 +1,64 @@
+* QCOM IOMMU
+
+The MSM IOMMU is an implementation compatible with the ARM VMSA short
+descriptor page tables. It provides address translation for bus masters outside
+of the CPU, each connected to the IOMMU through a port called micro-TLB.
+
+Required Properties:
+
+  - compatible: Must contain "qcom,apq8064-iommu".
+  - reg: Base address and size of the IOMMU registers.
+  - interrupts: Specifiers for the MMU fault interrupts. For instances that
+    support secure mode two interrupts must be specified, for non-secure and
+    secure mode, in that order. For instances that don't support secure mode a
+    single interrupt must be specified.
+  - #iommu-cells: The number of cells needed to specify the stream id. This
+		  is always 1.
+  - qcom,ncb:	  The total number of context banks in the IOMMU.
+  - clocks	: List of clocks to be used during SMMU register access. See
+		  Documentation/devicetree/bindings/clock/clock-bindings.txt
+		  for information about the format. For each clock specified
+		  here, there must be a corresponding entry in clock-names
+		  (see below).
+
+  - clock-names	: List of clock names corresponding to the clocks specified in
+		  the "clocks" property (above).
+		  Should be "smmu_pclk" for specifying the interface clock
+		  required for iommu's register accesses.
+		  Should be "smmu_clk" for specifying the functional clock
+		  required by iommu for bus accesses.
+
+Each bus master connected to an IOMMU must reference the IOMMU in its device
+node with the following property:
+
+  - iommus: A reference to the IOMMU in multiple cells. The first cell is a
+	    phandle to the IOMMU and the second cell is the stream id.
+	    A single master device can be connected to more than one iommu
+	    and multiple contexts in each of the iommu. So multiple entries
+	    are required to list all the iommus and the stream ids that the
+	    master is connected to.
+
+Example: mdp iommu and its bus master
+
+                mdp_port0: iommu@7500000 {
+			compatible = "qcom,apq8064-iommu";
+			#iommu-cells = <1>;
+			clock-names =
+			    "smmu_pclk",
+			    "smmu_clk";
+			clocks =
+			    <&mmcc SMMU_AHB_CLK>,
+			    <&mmcc MDP_AXI_CLK>;
+			reg = <0x07500000 0x100000>;
+			interrupts =
+			    <GIC_SPI 63 0>,
+			    <GIC_SPI 64 0>;
+			qcom,ncb = <2>;
+		};
+
+		mdp: qcom,mdp@5100000 {
+			compatible = "qcom,mdp";
+			...
+			iommus = <&mdp_port0 0
+				  &mdp_port0 2>;
+		};

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt

@@ -2,16 +2,31 @@ SMI (Smart Multimedia Interface) Common
 
 The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
 
+Mediatek SMI have two generations of HW architecture, mt8173 uses the second
+generation of SMI HW while mt2701 uses the first generation HW of SMI.
+
+There's slight differences between the two SMI, for generation 2, the
+register which control the iommu port is at each larb's register base. But
+for generation 1, the register is at smi ao base(smi always on register
+base). Besides that, the smi async clock should be prepared and enabled for
+SMI generation 1 to transform the smi clock into emi clock domain, but that is
+not needed for SMI generation 2.
+
 Required properties:
-- compatible : must be "mediatek,mt8173-smi-common"
+- compatible : must be one of :
+	"mediatek,mt2701-smi-common"
+	"mediatek,mt8173-smi-common"
 - reg : the register and size of the SMI block.
 - power-domains : a phandle to the power domain of this local arbiter.
 - clocks : Must contain an entry for each entry in clock-names.
-- clock-names : must contain 2 entries, as follows:
+- clock-names : must contain 3 entries for generation 1 smi HW and 2 entries
+  for generation 2 smi HW as follows:
   - "apb" : Advanced Peripheral Bus clock, It's the clock for setting
 	    the register.
   - "smi" : It's the clock for transfer data and command.
-  They may be the same if both source clocks are the same.
+	    They may be the same if both source clocks are the same.
+  - "async" : asynchronous clock, it help transform the smi clock into the emi
+	      clock domain, this clock is only needed by generation 1 smi HW.
 
 Example:
 	smi_common: smi@14022000 {

Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt

@@ -3,7 +3,9 @@ SMI (Smart Multimedia Interface) Local Arbiter
 The hardware block diagram please check bindings/iommu/mediatek,iommu.txt
 
 Required properties:
-- compatible : must be "mediatek,mt8173-smi-larb"
+- compatible : must be one of :
+		"mediatek,mt8173-smi-larb"
+		"mediatek,mt2701-smi-larb"
 - reg : the register and size of this local arbiter.
 - mediatek,smi : a phandle to the smi_common node.
 - power-domains : a phandle to the power domain of this local arbiter.

MAINTAINERS

@@ -6144,6 +6144,7 @@ M:	Joerg Roedel <joro@8bytes.org>
 L:	iommu@lists.linux-foundation.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu.git
 S:	Maintained
+F:	Documentation/devicetree/bindings/iommu/
 F:	drivers/iommu/
 
 IP MASQUERADING

drivers/iommu/Kconfig

@@ -89,8 +89,8 @@ config MSM_IOMMU
 	bool "MSM IOMMU Support"
 	depends on ARM
 	depends on ARCH_MSM8X60 || ARCH_MSM8960 || COMPILE_TEST
-	depends on BROKEN
 	select IOMMU_API
+	select IOMMU_IO_PGTABLE_ARMV7S
 	help
 	  Support for the IOMMUs found on certain Qualcomm SOCs.
 	  These IOMMUs allow virtualization of the address space used by most
@@ -111,6 +111,7 @@ config AMD_IOMMU
 	select PCI_PRI
 	select PCI_PASID
 	select IOMMU_API
+	select IOMMU_IOVA
 	depends on X86_64 && PCI && ACPI
 	---help---
 	  With this option you can enable support for AMD IOMMU hardware in
@@ -343,4 +344,22 @@ config MTK_IOMMU
 
 	  If unsure, say N here.
 
+config MTK_IOMMU_V1
+	bool "MTK IOMMU Version 1 (M4U gen1) Support"
+	depends on ARM
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	select ARM_DMA_USE_IOMMU
+	select IOMMU_API
+	select MEMORY
+	select MTK_SMI
+	select COMMON_CLK_MT2701_MMSYS
+	select COMMON_CLK_MT2701_IMGSYS
+	select COMMON_CLK_MT2701_VDECSYS
+	help
+	  Support for the M4U on certain Mediatek SoCs. M4U generation 1 HW is
+	  Multimedia Memory Managememt Unit. This option enables remapping of
+	  DMA memory accesses for the multimedia subsystem.
+
+	  if unsure, say N here.
+
 endif # IOMMU_SUPPORT

drivers/iommu/Makefile

@@ -7,7 +7,7 @@ obj-$(CONFIG_IOMMU_IO_PGTABLE_ARMV7S) += io-pgtable-arm-v7s.o
 obj-$(CONFIG_IOMMU_IO_PGTABLE_LPAE) += io-pgtable-arm.o
 obj-$(CONFIG_IOMMU_IOVA) += iova.o
 obj-$(CONFIG_OF_IOMMU)	+= of_iommu.o
-obj-$(CONFIG_MSM_IOMMU) += msm_iommu.o msm_iommu_dev.o
+obj-$(CONFIG_MSM_IOMMU) += msm_iommu.o
 obj-$(CONFIG_AMD_IOMMU) += amd_iommu.o amd_iommu_init.o
 obj-$(CONFIG_AMD_IOMMU_V2) += amd_iommu_v2.o
 obj-$(CONFIG_ARM_SMMU) += arm-smmu.o
@@ -18,6 +18,7 @@ obj-$(CONFIG_INTEL_IOMMU_SVM) += intel-svm.o
 obj-$(CONFIG_IPMMU_VMSA) += ipmmu-vmsa.o
 obj-$(CONFIG_IRQ_REMAP) += intel_irq_remapping.o irq_remapping.o
 obj-$(CONFIG_MTK_IOMMU) += mtk_iommu.o
+obj-$(CONFIG_MTK_IOMMU_V1) += mtk_iommu_v1.o
 obj-$(CONFIG_OMAP_IOMMU) += omap-iommu.o
 obj-$(CONFIG_OMAP_IOMMU_DEBUG) += omap-iommu-debug.o
 obj-$(CONFIG_ROCKCHIP_IOMMU) += rockchip-iommu.o