Merge tag 'tty-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/…

…git/gregkh/tty

Pull tty/serial fixes from Greg Kroah-Hartman:
 "Here are 4 small tty/serial fixes for 3.9.

  One fixes a bug where we broke the documentation build, and the others
  fix reported problems in some serial drivers.

  All have been in linux-next for a while"

* tag 'tty-3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: mxser: fix cycle termination condition in mxser_probe() and mxser_module_init()
  Revert "tty/8250_pnp: serial port detection regression since v3.7"
  OMAP/serial: Revert bad fix of Rx FIFO threshold granularity
  tty: Documentation: fix a path in a DocBook template

Documentation/DocBook/device-drivers.tmpl

@@ -227,7 +227,7 @@ X!Isound/sound_firmware.c
   <chapter id="uart16x50">
      <title>16x50 UART Driver</title>
 !Edrivers/tty/serial/serial_core.c
-!Edrivers/tty/serial/8250/8250.c
+!Edrivers/tty/serial/8250/8250_core.c
   </chapter>
 
   <chapter id="fbdev">

drivers/tty/mxser.c

@@ -2643,9 +2643,9 @@ static int mxser_probe(struct pci_dev *pdev,
 				mxvar_sdriver, brd->idx + i, &pdev->dev);
 		if (IS_ERR(tty_dev)) {
 			retval = PTR_ERR(tty_dev);
-			for (i--; i >= 0; i--)
+			for (; i > 0; i--)
 				tty_unregister_device(mxvar_sdriver,
-					brd->idx + i);
+					brd->idx + i - 1);
 			goto err_relbrd;
 		}
 	}
@@ -2751,9 +2751,9 @@ static int __init mxser_module_init(void)
 			tty_dev = tty_port_register_device(&brd->ports[i].port,
 					mxvar_sdriver, brd->idx + i, NULL);
 			if (IS_ERR(tty_dev)) {
-				for (i--; i >= 0; i--)
+				for (; i > 0; i--)
 					tty_unregister_device(mxvar_sdriver,
-						brd->idx + i);
+						brd->idx + i - 1);
 				for (i = 0; i < brd->info->nports; i++)
 					tty_port_destroy(&brd->ports[i].port);
 				free_irq(brd->irq, brd);

drivers/tty/serial/8250/8250_pnp.c

@@ -429,7 +429,6 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 {
 	struct uart_8250_port uart;
 	int ret, line, flags = dev_id->driver_data;
-	struct resource *res = NULL;
 
 	if (flags & UNKNOWN_DEV) {
 		ret = serial_pnp_guess_board(dev);
@@ -440,12 +439,11 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 	memset(&uart, 0, sizeof(uart));
 	if (pnp_irq_valid(dev, 0))
 		uart.port.irq = pnp_irq(dev, 0);
-	if ((flags & CIR_PORT) && pnp_port_valid(dev, 2))
-		res = pnp_get_resource(dev, IORESOURCE_IO, 2);
-	else if (pnp_port_valid(dev, 0))
-		res = pnp_get_resource(dev, IORESOURCE_IO, 0);
-	if (pnp_resource_enabled(res)) {
-		uart.port.iobase = res->start;
+	if ((flags & CIR_PORT) && pnp_port_valid(dev, 2)) {
+		uart.port.iobase = pnp_port_start(dev, 2);
+		uart.port.iotype = UPIO_PORT;
+	} else if (pnp_port_valid(dev, 0)) {
+		uart.port.iobase = pnp_port_start(dev, 0);
 		uart.port.iotype = UPIO_PORT;
 	} else if (pnp_mem_valid(dev, 0)) {
 		uart.port.mapbase = pnp_mem_start(dev, 0);

drivers/tty/serial/omap-serial.c

@@ -886,6 +886,17 @@ serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
 	serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
 	/* FIFO ENABLE, DMA MODE */
 
+	up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
+	/*
+	 * NOTE: Setting OMAP_UART_SCR_RX_TRIG_GRANU1_MASK
+	 * sets Enables the granularity of 1 for TRIGGER RX
+	 * level. Along with setting RX FIFO trigger level
+	 * to 1 (as noted below, 16 characters) and TLR[3:0]
+	 * to zero this will result RX FIFO threshold level
+	 * to 1 character, instead of 16 as noted in comment
+	 * below.
+	 */
+
 	/* Set receive FIFO threshold to 16 characters and
 	 * transmit FIFO threshold to 16 spaces
 	 */