phy: qcom-ufs: add support for 20nm phy

This change adds a support for a 20nm qcom-ufs phy that is required in
platforms that use ufs-qcom controller.

Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Reviewed-by: Dov Levenglick <dovl@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>

drivers/phy/Makefile

@@ -35,3 +35,4 @@ obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
 obj-$(CONFIG_PHY_STIH407_USB)		+= phy-stih407-usb.o
 obj-$(CONFIG_PHY_STIH41X_USB)		+= phy-stih41x-usb.o
 obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs.o
+obj-$(CONFIG_PHY_QCOM_UFS) 	+= phy-qcom-ufs-qmp-20nm.o

drivers/phy/phy-qcom-ufs-i.h

@@ -15,15 +15,56 @@
 #ifndef UFS_QCOM_PHY_I_H_
 #define UFS_QCOM_PHY_I_H_
 
+#include <linux/module.h>
 #include <linux/clk.h>
+#include <linux/regulator/consumer.h>
 #include <linux/slab.h>
-#include <linux/phy/phy.h>
+#include <linux/phy/phy-qcom-ufs.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/delay.h>
 
+#define readl_poll_timeout(addr, val, cond, sleep_us, timeout_us) \
+({ \
+	ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \
+	might_sleep_if(timeout_us); \
+	for (;;) { \
+		(val) = readl(addr); \
+		if (cond) \
+			break; \
+		if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \
+			(val) = readl(addr); \
+			break; \
+		} \
+		if (sleep_us) \
+			usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \
+	} \
+	(cond) ? 0 : -ETIMEDOUT; \
+})
+
+#define UFS_QCOM_PHY_CAL_ENTRY(reg, val)	\
+	{				\
+		.reg_offset = reg,	\
+		.cfg_value = val,	\
+	}
+
 #define UFS_QCOM_PHY_NAME_LEN	30
 
+enum {
+	MASK_SERDES_START       = 0x1,
+	MASK_PCS_READY          = 0x1,
+};
+
+enum {
+	OFFSET_SERDES_START     = 0x0,
+};
+
+struct ufs_qcom_phy_stored_attributes {
+	u32 att;
+	u32 value;
+};
+
+
 struct ufs_qcom_phy_calibration {
 	u32 reg_offset;
 	u32 cfg_value;

drivers/phy/phy-qcom-ufs-qmp-20nm.c

@@ -0,0 +1,257 @@
+/*
+ * Copyright (c) 2013-2015, Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include "phy-qcom-ufs-qmp-20nm.h"
+
+#define UFS_PHY_NAME "ufs_phy_qmp_20nm"
+
+static
+int ufs_qcom_phy_qmp_20nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy,
+					bool is_rate_B)
+{
+	struct ufs_qcom_phy_calibration *tbl_A, *tbl_B;
+	int tbl_size_A, tbl_size_B;
+	u8 major = ufs_qcom_phy->host_ctrl_rev_major;
+	u16 minor = ufs_qcom_phy->host_ctrl_rev_minor;
+	u16 step = ufs_qcom_phy->host_ctrl_rev_step;
+	int err;
+
+	if ((major == 0x1) && (minor == 0x002) && (step == 0x0000)) {
+		tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_2_0);
+		tbl_A = phy_cal_table_rate_A_1_2_0;
+	} else if ((major == 0x1) && (minor == 0x003) && (step == 0x0000)) {
+		tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A_1_3_0);
+		tbl_A = phy_cal_table_rate_A_1_3_0;
+	} else {
+		dev_err(ufs_qcom_phy->dev, "%s: Unknown UFS-PHY version, no calibration values\n",
+			__func__);
+		err = -ENODEV;
+		goto out;
+	}
+
+	tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B);
+	tbl_B = phy_cal_table_rate_B;
+
+	err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A,
+						tbl_B, tbl_size_B, is_rate_B);
+
+	if (err)
+		dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n",
+			__func__, err);
+
+out:
+	return err;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common)
+{
+	phy_common->quirks =
+		UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+}
+
+static int ufs_qcom_phy_qmp_20nm_init(struct phy *generic_phy)
+{
+	struct ufs_qcom_phy_qmp_20nm *phy = phy_get_drvdata(generic_phy);
+	struct ufs_qcom_phy *phy_common = &phy->common_cfg;
+	int err = 0;
+
+	err = ufs_qcom_phy_init_clks(generic_phy, phy_common);
+	if (err) {
+		dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_clks() failed %d\n",
+			__func__, err);
+		goto out;
+	}
+
+	err = ufs_qcom_phy_init_vregulators(generic_phy, phy_common);
+	if (err) {
+		dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_vregulators() failed %d\n",
+			__func__, err);
+		goto out;
+	}
+
+	ufs_qcom_phy_qmp_20nm_advertise_quirks(phy_common);
+
+out:
+	return err;
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_power_control(struct ufs_qcom_phy *phy, bool val)
+{
+	bool hibern8_exit_after_pwr_collapse = phy->quirks &
+		UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE;
+
+	if (val) {
+		writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+		/*
+		 * Before any transactions involving PHY, ensure PHY knows
+		 * that it's analog rail is powered ON.
+		 */
+		mb();
+
+		if (hibern8_exit_after_pwr_collapse) {
+			/*
+			 * Give atleast 1us delay after restoring PHY analog
+			 * power.
+			 */
+			usleep_range(1, 2);
+			writel_relaxed(0x0A, phy->mmio +
+				       QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+			writel_relaxed(0x08, phy->mmio +
+				       QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+			/*
+			 * Make sure workaround is deactivated before proceeding
+			 * with normal PHY operations.
+			 */
+			mb();
+		}
+	} else {
+		if (hibern8_exit_after_pwr_collapse) {
+			writel_relaxed(0x0A, phy->mmio +
+				       QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+			writel_relaxed(0x02, phy->mmio +
+				       QSERDES_COM_SYSCLK_EN_SEL_TXBAND);
+			/*
+			 * Make sure that above workaround is activated before
+			 * PHY analog power collapse.
+			 */
+			mb();
+		}
+
+		writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL);
+		/*
+		 * ensure that PHY knows its PHY analog rail is going
+		 * to be powered down
+		 */
+		mb();
+	}
+}
+
+static
+void ufs_qcom_phy_qmp_20nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val)
+{
+	writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK,
+			phy->mmio + UFS_PHY_TX_LANE_ENABLE);
+	mb();
+}
+
+static inline void ufs_qcom_phy_qmp_20nm_start_serdes(struct ufs_qcom_phy *phy)
+{
+	u32 tmp;
+
+	tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START);
+	tmp &= ~MASK_SERDES_START;
+	tmp |= (1 << OFFSET_SERDES_START);
+	writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START);
+	mb();
+}
+
+static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common)
+{
+	int err = 0;
+	u32 val;
+
+	err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS,
+			val, (val & MASK_PCS_READY), 10, 1000000);
+	if (err)
+		dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n",
+			__func__, err);
+	return err;
+}
+
+static struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = {
+	.init		= ufs_qcom_phy_qmp_20nm_init,
+	.exit		= ufs_qcom_phy_exit,
+	.power_on	= ufs_qcom_phy_power_on,
+	.power_off	= ufs_qcom_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static struct ufs_qcom_phy_specific_ops phy_20nm_ops = {
+	.calibrate_phy		= ufs_qcom_phy_qmp_20nm_phy_calibrate,
+	.start_serdes		= ufs_qcom_phy_qmp_20nm_start_serdes,
+	.is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready,
+	.set_tx_lane_enable	= ufs_qcom_phy_qmp_20nm_set_tx_lane_enable,
+	.power_control		= ufs_qcom_phy_qmp_20nm_power_control,
+};
+
+static int ufs_qcom_phy_qmp_20nm_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy *generic_phy;
+	struct ufs_qcom_phy_qmp_20nm *phy;
+	int err = 0;
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy) {
+		dev_err(dev, "%s: failed to allocate phy\n", __func__);
+		err = -ENOMEM;
+		goto out;
+	}
+
+	generic_phy = ufs_qcom_phy_generic_probe(pdev, &phy->common_cfg,
+				&ufs_qcom_phy_qmp_20nm_phy_ops, &phy_20nm_ops);
+
+	if (!generic_phy) {
+		dev_err(dev, "%s: ufs_qcom_phy_generic_probe() failed\n",
+			__func__);
+		err = -EIO;
+		goto out;
+	}
+
+	phy_set_drvdata(generic_phy, phy);
+
+	strlcpy(phy->common_cfg.name, UFS_PHY_NAME,
+			sizeof(phy->common_cfg.name));
+
+out:
+	return err;
+}
+
+static int ufs_qcom_phy_qmp_20nm_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct phy *generic_phy = to_phy(dev);
+	struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy);
+	int err = 0;
+
+	err = ufs_qcom_phy_remove(generic_phy, ufs_qcom_phy);
+	if (err)
+		dev_err(dev, "%s: ufs_qcom_phy_remove failed = %d\n",
+			__func__, err);
+
+	return err;
+}
+
+static const struct of_device_id ufs_qcom_phy_qmp_20nm_of_match[] = {
+	{.compatible = "qcom,ufs-phy-qmp-20nm"},
+	{},
+};
+MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_20nm_of_match);
+
+static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = {
+	.probe = ufs_qcom_phy_qmp_20nm_probe,
+	.remove = ufs_qcom_phy_qmp_20nm_remove,
+	.driver = {
+		.of_match_table = ufs_qcom_phy_qmp_20nm_of_match,
+		.name = "ufs_qcom_phy_qmp_20nm",
+		.owner = THIS_MODULE,
+	},
+};
+
+module_platform_driver(ufs_qcom_phy_qmp_20nm_driver);
+
+MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 20nm");
+MODULE_LICENSE("GPL v2");