Merge branch 'acpi-scan' to satisfy dependencies.

Documentation/admin-guide/kernel-parameters.txt

@@ -4846,3 +4846,8 @@
 	xirc2ps_cs=	[NET,PCMCIA]
 			Format:
 			<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
+
+	xhci-hcd.quirks		[USB,KNL]
+			A hex value specifying bitmask with supplemental xhci
+			host controller quirks. Meaning of each bit can be
+			consulted in header drivers/usb/host/xhci.h.

Documentation/device-mapper/writecache.txt

@@ -15,6 +15,8 @@ Constructor parameters:
    size)
 5. the number of optional parameters (the parameters with an argument
    count as two)
+	start_sector n		(default: 0)
+		offset from the start of cache device in 512-byte sectors
 	high_watermark n	(default: 50)
 		start writeback when the number of used blocks reach this
 		watermark

Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt

@@ -66,7 +66,7 @@ Required root node properties:
 	- "insignal,arndale-octa" - for Exynos5420-based Insignal Arndale
 				    Octa board.
 	- "insignal,origen"       - for Exynos4210-based Insignal Origen board.
-	- "insignal,origen4412    - for Exynos4412-based Insignal Origen board.
+	- "insignal,origen4412"   - for Exynos4412-based Insignal Origen board.
 
 
 Optional nodes:

Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt

@@ -36,7 +36,7 @@ Optional nodes:
 
  - port/ports: to describe a connection to an external encoder. The
    binding follows Documentation/devicetree/bindings/graph.txt and
-   suppors a single port with a single endpoint.
+   supports a single port with a single endpoint.
 
  - See also Documentation/devicetree/bindings/display/tilcdc/panel.txt and
    Documentation/devicetree/bindings/display/tilcdc/tfp410.txt for connecting

Documentation/devicetree/bindings/gpio/nintendo,hollywood-gpio.txt

@@ -1,7 +1,7 @@
 Nintendo Wii (Hollywood) GPIO controller
 
 Required properties:
-- compatible: "nintendo,hollywood-gpio
+- compatible: "nintendo,hollywood-gpio"
 - reg: Physical base address and length of the controller's registers.
 - gpio-controller: Marks the device node as a GPIO controller.
 - #gpio-cells: Should be <2>. The first cell is the pin number and the

Documentation/devicetree/bindings/input/touchscreen/hideep.txt

@@ -32,7 +32,7 @@ i2c@00000000 {
 		reg = <0x6c>;
 		interrupt-parent = <&gpx1>;
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
-		vdd-supply = <&ldo15_reg>";
+		vdd-supply = <&ldo15_reg>;
 		vid-supply = <&ldo18_reg>;
 		reset-gpios = <&gpx1 5 0>;
 		touchscreen-size-x = <1080>;

Documentation/devicetree/bindings/interrupt-controller/nvidia,tegra20-ictlr.txt

@@ -15,7 +15,7 @@ Required properties:
   include "nvidia,tegra30-ictlr".	
 - reg : Specifies base physical address and size of the registers.
   Each controller must be described separately (Tegra20 has 4 of them,
-  whereas Tegra30 and later have 5"  
+  whereas Tegra30 and later have 5).
 - interrupt-controller : Identifies the node as an interrupt controller.
 - #interrupt-cells : Specifies the number of cells needed to encode an
   interrupt source. The value must be 3.

Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt

@@ -12,7 +12,7 @@ Required properties:
   specifier, shall be 2
 - interrupts: interrupts references to primary interrupt controller
   (only needed for exti controller with multiple exti under
-  same parent interrupt: st,stm32-exti and st,stm32h7-exti")
+  same parent interrupt: st,stm32-exti and st,stm32h7-exti)
 
 Example:
 

Documentation/devicetree/bindings/mips/brcm/soc.txt

@@ -152,7 +152,7 @@ Required properties:
 - compatible	: should contain one of:
 		  "brcm,bcm7425-timers"
 		  "brcm,bcm7429-timers"
-		  "brcm,bcm7435-timers and
+		  "brcm,bcm7435-timers" and
 		  "brcm,brcmstb-timers"
 - reg		: the timers register range
 - interrupts	: the interrupt line for this timer block

Documentation/devicetree/bindings/net/fsl-fman.txt

@@ -238,7 +238,7 @@ PROPERTIES
 		Must include one of the following:
 		- "fsl,fman-dtsec" for dTSEC MAC
 		- "fsl,fman-xgec" for XGEC MAC
-		- "fsl,fman-memac for mEMAC MAC
+		- "fsl,fman-memac" for mEMAC MAC
 
 - cell-index
 		Usage: required

Documentation/devicetree/bindings/power/power_domain.txt

@@ -133,7 +133,7 @@ located inside a PM domain with index 0 of a power controller represented by a
 node with the label "power".
 In the second example the consumer device are partitioned across two PM domains,
 the first with index 0 and the second with index 1, of a power controller that
-is represented by a node with the label "power.
+is represented by a node with the label "power".
 
 Optional properties:
 - required-opps: This contains phandle to an OPP node in another device's OPP

Documentation/devicetree/bindings/regulator/tps65090.txt

@@ -16,7 +16,7 @@ Required properties:
 Optional properties:
 - ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled then this property should be there.
-- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+- dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
   If DCDCs are externally controlled and if it is from GPIO then GPIO
   number should be provided. If it is externally controlled and no GPIO
   entry then driver will just configure this rails as external control

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

@@ -15,7 +15,7 @@ Please refer to reset.txt in this directory for common reset
 controller binding usage.
 
 Required properties:
-- compatible: Should be st,stih407-softreset";
+- compatible: Should be "st,stih407-softreset";
 - #reset-cells: 1, see below
 
 example:

Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt

@@ -39,7 +39,7 @@ Required properties:
 
 Optional property:
 - clock-frequency:	Desired I2C bus clock frequency in Hz.
-			When missing default to 400000Hz.
+			When missing default to 100000Hz.
 
 Child nodes should conform to I2C bus binding as described in i2c.txt.
 

Documentation/devicetree/bindings/sound/qcom,apq8016-sbc.txt

@@ -30,7 +30,7 @@ Required properties:
 
 			  Board connectors:
 			  * Headset Mic
-			  * Secondary Mic",
+			  * Secondary Mic
 			  * DMIC
 			  * Ext Spk
 

Documentation/devicetree/bindings/sound/qcom,apq8096.txt

@@ -35,7 +35,7 @@ This binding describes the APQ8096 sound card, which uses qdsp for audio.
 			"Digital Mic3"
 
 		Audio pins and MicBias on WCD9335 Codec:
-			"MIC_BIAS1
+			"MIC_BIAS1"
 			"MIC_BIAS2"
 			"MIC_BIAS3"
 			"MIC_BIAS4"

Documentation/devicetree/bindings/usb/rockchip,dwc3.txt

@@ -16,7 +16,8 @@ A child node must exist to represent the core DWC3 IP block. The name of
 the node is not important. The content of the node is defined in dwc3.txt.
 
 Phy documentation is provided in the following places:
-Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt
+Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt - USB2.0 PHY
+Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt     - Type-C PHY
 
 Example device nodes:
 

Documentation/devicetree/bindings/w1/w1-gpio.txt

@@ -15,7 +15,7 @@ Optional properties:
 
 Examples:
 
-	onewire@0 {
+	onewire {
 		compatible = "w1-gpio";
 		gpios = <&gpio 126 0>, <&gpio 105 0>;
 	};

Documentation/kbuild/kbuild.txt

@@ -50,6 +50,11 @@ LDFLAGS_MODULE
 --------------------------------------------------
 Additional options used for $(LD) when linking modules.
 
+KBUILD_KCONFIG
+--------------------------------------------------
+Set the top-level Kconfig file to the value of this environment
+variable.  The default name is "Kconfig".
+
 KBUILD_VERBOSE
 --------------------------------------------------
 Set the kbuild verbosity. Can be assigned same values as "V=...".
@@ -88,7 +93,8 @@ In most cases the name of the architecture is the same as the
 directory name found in the arch/ directory.
 But some architectures such as x86 and sparc have aliases.
 x86: i386 for 32 bit, x86_64 for 64 bit
-sparc: sparc for 32 bit, sparc64 for 64 bit
+sh: sh for 32 bit, sh64 for 64 bit
+sparc: sparc32 for 32 bit, sparc64 for 64 bit
 
 CROSS_COMPILE
 --------------------------------------------------
@@ -148,15 +154,6 @@ stripped after they are installed.  If INSTALL_MOD_STRIP is '1', then
 the default option --strip-debug will be used.  Otherwise,
 INSTALL_MOD_STRIP value will be used as the options to the strip command.
 
-INSTALL_FW_PATH
---------------------------------------------------
-INSTALL_FW_PATH specifies where to install the firmware blobs.
-The default value is:
-
-    $(INSTALL_MOD_PATH)/lib/firmware
-
-The value can be overridden in which case the default value is ignored.
-
 INSTALL_HDR_PATH
 --------------------------------------------------
 INSTALL_HDR_PATH specifies where to install user space headers when

Documentation/kbuild/kconfig.txt

@@ -2,9 +2,9 @@ This file contains some assistance for using "make *config".
 
 Use "make help" to list all of the possible configuration targets.
 
-The xconfig ('qconf') and menuconfig ('mconf') programs also
-have embedded help text.  Be sure to check it for navigation,
-search, and other general help text.
+The xconfig ('qconf'), menuconfig ('mconf'), and nconfig ('nconf')
+programs also have embedded help text.  Be sure to check that for
+navigation, search, and other general help text.
 
 ======================================================================
 General
@@ -17,13 +17,16 @@ this happens, using a previously working .config file and running
 for you, so you may find that you need to see what NEW kernel
 symbols have been introduced.
 
-To see a list of new config symbols when using "make oldconfig", use
+To see a list of new config symbols, use
 
 	cp user/some/old.config .config
 	make listnewconfig
 
 and the config program will list any new symbols, one per line.
 
+Alternatively, you can use the brute force method:
+
+	make oldconfig
 	scripts/diffconfig .config.old .config | less
 
 ______________________________________________________________________
@@ -160,7 +163,7 @@ Searching in menuconfig:
 		This lists all config symbols that contain "hotplug",
 		e.g., HOTPLUG_CPU, MEMORY_HOTPLUG.
 
-	For search help, enter / followed TAB-TAB-TAB (to highlight
+	For search help, enter / followed by TAB-TAB (to highlight
 	<Help>) and Enter.  This will tell you that you can also use
 	regular expressions (regexes) in the search string, so if you
 	are not interested in MEMORY_HOTPLUG, you could try
@@ -202,6 +205,39 @@ Example:
 	make MENUCONFIG_MODE=single_menu menuconfig
 
 
+======================================================================
+nconfig
+--------------------------------------------------
+
+nconfig is an alternate text-based configurator.  It lists function
+keys across the bottom of the terminal (window) that execute commands.
+You can also just use the corresponding numeric key to execute the
+commands unless you are in a data entry window.  E.g., instead of F6
+for Save, you can just press 6.
+
+Use F1 for Global help or F3 for the Short help menu.
+
+Searching in nconfig:
+
+	You can search either in the menu entry "prompt" strings
+	or in the configuration symbols.
+
+	Use / to begin a search through the menu entries.  This does
+	not support regular expressions.  Use <Down> or <Up> for
+	Next hit and Previous hit, respectively.  Use <Esc> to
+	terminate the search mode.
+
+	F8 (SymSearch) searches the configuration symbols for the
+	given string or regular expression (regex).
+
+NCONFIG_MODE
+--------------------------------------------------
+This mode shows all sub-menus in one large tree.
+
+Example:
+	make NCONFIG_MODE=single_menu nconfig
+
+
 ======================================================================
 xconfig
 --------------------------------------------------
@@ -230,8 +266,7 @@ gconfig
 
 Searching in gconfig:
 
-	None (gconfig isn't maintained as well as xconfig or menuconfig);
-	however, gconfig does have a few more viewing choices than
-	xconfig does.
+	There is no search command in gconfig.  However, gconfig does
+	have several different viewing choices, modes, and options.
 
 ###

Documentation/networking/bonding.txt

@@ -1490,7 +1490,7 @@ To remove an ARP target:
 
 To configure the interval between learning packet transmits:
 # echo 12 > /sys/class/net/bond0/bonding/lp_interval
-	NOTE: the lp_inteval is the number of seconds between instances where
+	NOTE: the lp_interval is the number of seconds between instances where
 the bonding driver sends learning packets to each slaves peer switch.  The
 default interval is 1 second.
 

Documentation/networking/dpaa2/overview.rst

@@ -1,5 +1,6 @@
 .. include:: <isonum.txt>
 
+=========================================================
 DPAA2 (Data Path Acceleration Architecture Gen2) Overview
 =========================================================
 

Documentation/networking/e100.rst

@@ -47,41 +47,45 @@ Driver Configuration Parameters
 The default value for each parameter is generally the recommended setting,
 unless otherwise noted.
 
-Rx Descriptors: Number of receive descriptors. A receive descriptor is a data
+Rx Descriptors:
+   Number of receive descriptors. A receive descriptor is a data
    structure that describes a receive buffer and its attributes to the network
    controller. The data in the descriptor is used by the controller to write
    data from the controller to host memory. In the 3.x.x driver the valid range
    for this parameter is 64-256. The default value is 256. This parameter can be
    changed using the command::
 
-   ethtool -G eth? rx n
+     ethtool -G eth? rx n
 
    Where n is the number of desired Rx descriptors.
 
-Tx Descriptors: Number of transmit descriptors. A transmit descriptor is a data
+Tx Descriptors:
+   Number of transmit descriptors. A transmit descriptor is a data
    structure that describes a transmit buffer and its attributes to the network
    controller. The data in the descriptor is used by the controller to read
    data from the host memory to the controller. In the 3.x.x driver the valid
    range for this parameter is 64-256. The default value is 128. This parameter
    can be changed using the command::
 
-   ethtool -G eth? tx n
+     ethtool -G eth? tx n
 
    Where n is the number of desired Tx descriptors.
 
-Speed/Duplex: The driver auto-negotiates the link speed and duplex settings by
+Speed/Duplex:
+   The driver auto-negotiates the link speed and duplex settings by
    default. The ethtool utility can be used as follows to force speed/duplex.::
 
-   ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
+     ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
 
    NOTE: setting the speed/duplex to incorrect values will cause the link to
    fail.
 
-Event Log Message Level:  The driver uses the message level flag to log events
+Event Log Message Level:
+   The driver uses the message level flag to log events
    to syslog. The message level can be set at driver load time. It can also be
    set using the command::
 
-   ethtool -s eth? msglvl n
+     ethtool -s eth? msglvl n
 
 
 Additional Configurations
@@ -92,7 +96,7 @@ Configuring the Driver on Different Distributions
 
 Configuring a network driver to load properly when the system is started
 is distribution dependent.  Typically, the configuration process involves
-adding an alias line to /etc/modprobe.d/*.conf as well as editing other
+adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other
 system startup scripts and/or configuration files.  Many popular Linux
 distributions ship with tools to make these changes for you.  To learn
 the proper way to configure a network device for your system, refer to
@@ -160,7 +164,10 @@ This results in unbalanced receive traffic.
 If you have multiple interfaces in a server, either turn on ARP
 filtering by
 
-(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+(1) entering::
+
+	echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+
     (this only works if your kernel's version is higher than 2.4.5), or
 
 (2) installing the interfaces in separate broadcast domains (either