suitability for HP 200LX?

[ishotjr]

Has anyone run ELKS on the V20-based HP 200LX? I'd like to give it a try but the lack of floppy disk and requirement to instead write to PCMCIA (or CF) from Linux will be a bit more of a challenge, so I wanted to get a feel for feasibility first? 💗

[ghaerr]

Hi @ishotjr, I should think ELKS will come up and run on the HP 200LX without problems. For your first pass, perhaps just grab a bootable image from the 0.8.0 Release page. Should there be issues, please report them and we might have to have you pull the repo and do a custom build, but we'll only know what is needed after seeing the boot screen.

Thank you!

[fehertamaskyndryl]

An educational purpose Uni*x clone called MINIX is available for HP 100/200/700LX and 1000 CX palmtops. It requires significant amount of tweaking to run on the unusual 80186 CPU + PCMCIA hardware.

[toncho11]

Now we have a CF card direct driver #2357 meaning that it might be used as an alternative to the BIOS HD driver for ELKS or if there is a problem with the BIOS HD driver. Chatgpt is confident that CompactFlash (CF) cards via PCMCIA (PC Card) adapters do expose the ATA (IDE) registers needed for this driver.

So yes this new driver might allow you to mount a CF card on these HP machines.

[toncho11]

Wow the base storage is a 2MB write once rom chip. Installing ELKS on it is nearly impossible as one needs to desolder, flash and put back a writable ROM. Quite a feat as all this is packed in a tiny space.

[ishotjr]

there's up to 4MB of RAM (depending on model/minus whatever is allocated to the system) that's bootable, but I'm really interested to learn about the CF support and will gladly give that a try once merged! ❣️

[toncho11]

there's up to 4MB of RAM (depending on model/minus whatever is allocated to the system) that's bootable, but I'm really interested to learn about the CF support and will gladly give that a try once merged! ❣️

How would you boot ELKS? Or maybe an image of ELKS can be stored in RAM and somehow ELKS can be booted from there?

[toncho11]

Can you force booting from the CF card instead of the internal drive? In this case everything is kind of OK.

[toncho11]

You mount the CF card from DOS and you try to boot an ELKS image from there? You need a special program for that similar to SYSLINUX or LOADLIN. There was something like that before, but it is not usable currently I think.

[ishotjr]

the device will boot to a PCMCIA card first if inserted, but I'm not sure if this is at the OS or BIOS level...

[fehertamaskyndryl]

Hello,
MINIX was booted on the HP 100/200/700LX/1000 CX palmtops by running a DOS program, which kicked DOS out of memory and loaded Unix. Here are the tech details:
https://web.archive.org/web/20060828125731/http://minix.technoir.org/

Note that HP palmtop used i80186 architecture CPU, which has no memory protection hardware whatsoever, so the OS loaded from ROM could be easily subverted. Because of that lack of memory protections (introduced from i286 and up), I doubt porting any kind of Linux would make much sense on the HP200LX. Even Windows 3.1 refused to run on it, needing a 286 CPU or better.

[fehertamaskyndryl]

I remember running Minix on my 200LX, using a 24MB CF card in a PCMCIA adapter, before the LCD's flat cable was destroyed by an unrelated battery leak. Minix was fairly complete, it even had wheatstone, etc. performance benchmarks and text-based games, like advent.

If I had a PCMCIA slot doubler for the palmtop, even TCP/IP could have been used in Minix, with the Accton EN-2216 or Silicom ethernet cards. I think the lack of convenient networking would be a big discouragement for trying to port Linux to 200LX, because the palmtop only has a non-standard infrared port and 115kbps RS-232 built in.

[fehertamaskyndryl]

The HP Omnigo 700LX was a special variant of the 200LX, where a PCMCIA slot-doubler was built into the palmtop body, housing a Nokia mobile data card for the direct-attach Nokia 2110 GMS phone and still providing one free slot for e.g. flash card. Some people have removed that GSM card and installed an Accton EN-2212 / 2216 ethernet instead, to run Minix or Windows 3.0 from flash card with TCP/IP networking. The 700LX is fairly rare however and had a design problem, where the overweight top half broke the main hinge, so most would be wrecks by now.

Between the ethernet PCMCIA cards, Accton brand had a benefit over Silicom, as the EN-2212/2216 could be used with over-clocked 200LX. It was fairly popular aftermarket modding to replace the factory CPU tact crystal (15.8 to 32MHz) but more HW mods or tweaked DOS drivers were required to compensate for the rushed timekeeping. See here: https://www.200lx.net/upgrade.htm

[fehertamaskyndryl]

In this Reddit thread there are photos of the "AccuRite DoubleSlot" PCMCIA adapter for the HP palmtop:
https://www.reddit.com/r/OldHandhelds/comments/1jww7i4/defective_hp_200lxbut_there_is_something_more/

[toncho11]

Here we are not talking about Linux, but ELKS. ELKS runs on anything from the original 8088 and above.
The tool needed is called bootelks and it is discussed here: #2117 (comment) It even mentions hp 200LX.

The tool is available here: https://github.com/rafael2k/bootelks
Honestly the procedure is not very clear. Maybe @rafael2k can elaborate more on that.
At least in theory it is doable.

[ghaerr]

MINIX was booted on the HP 100/200/700LX/1000 CX palmtops by running a DOS program, which kicked DOS out of memory and loaded Unix.

Yes, that program acts effectively as a boot loader and uses DOS to read the kernel image into memory, then jumps to it, much like MINIX is loaded from a real boot loader.

I doubt porting any kind of Linux would make much sense on the HP200LX. Even Windows 3.1 refused to run on it, needing a 286 CPU or better.

That's all true for standard Linux, but ELKS, derived from a 30+ year old fork of Linux in the very early days, implements the same POSIX set of system calls and runs on a wide variety of 8088/8086 machines in as little as 256K RAM. The system includes a bash-compatible shell and TCP/IP networking, all without any MMU.

I think the lack of convenient networking would be a big discouragement for trying to port Linux to 200LX, because the palmtop only has a non-standard infrared port and 115kbps RS-232 built in.

ELKS supports TCP/IP SLIP over serial and works great, along with included telnet and ftp client and servers.

photos of the "AccuRite DoubleSlot" PCMCIA adapter for the HP palmtop:

We've recently implemented CF support via ATA, XTIDE and XTCF, but I'm not familiar yet with how PCMCIA differs. That could be added, but certainly the first step would be someone actually going through the steps to boot ELKS on 200LX using bootelks. That will involved getting familiar with exactly how bootelks works. For those interested, I would recommend using bootelks on a DOS desktop getting ELKS booted first, then moving to doing the same on 200LX.