treewide: Linux 4.14.159

source kernel.org
https://cdn.kernel.org/pub/linux/kernel/v4.x/incr/patch-4.14.158-159.xz

Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>

Documentation/admin-guide/kernel-parameters.txt

@@ -4706,13 +4706,13 @@
 			Flags is a set of characters, each corresponding
 			to a common usb-storage quirk flag as follows:
 				a = SANE_SENSE (collect more than 18 bytes
-					of sense data);
+					of sense data, not on uas);
 				b = BAD_SENSE (don't collect more than 18
-					bytes of sense data);
+					bytes of sense data, not on uas);
 				c = FIX_CAPACITY (decrease the reported
 					device capacity by one sector);
 				d = NO_READ_DISC_INFO (don't use
-					READ_DISC_INFO command);
+					READ_DISC_INFO command, not on uas);
 				e = NO_READ_CAPACITY_16 (don't use
 					READ_CAPACITY_16 command);
 				f = NO_REPORT_OPCODES (don't use report opcodes
@@ -4727,17 +4727,18 @@
 				j = NO_REPORT_LUNS (don't use report luns
 					command, uas only);
 				l = NOT_LOCKABLE (don't try to lock and
-					unlock ejectable media);
+					unlock ejectable media, not on uas);
 				m = MAX_SECTORS_64 (don't transfer more
-					than 64 sectors = 32 KB at a time);
+					than 64 sectors = 32 KB at a time,
+					not on uas);
 				n = INITIAL_READ10 (force a retry of the
-					initial READ(10) command);
+					initial READ(10) command, not on uas);
 				o = CAPACITY_OK (accept the capacity
-					reported by the device);
+					reported by the device, not on uas);
 				p = WRITE_CACHE (the device cache is ON
-					by default);
+					by default, not on uas);
 				r = IGNORE_RESIDUE (the device reports
-					bogus residue values);
+					bogus residue values, not on uas);
 				s = SINGLE_LUN (the device has only one
 					Logical Unit);
 				t = NO_ATA_1X (don't allow ATA(12) and ATA(16)
@@ -4746,7 +4747,8 @@
 				w = NO_WP_DETECT (don't test whether the
 					medium is write-protected).
 				y = ALWAYS_SYNC (issue a SYNCHRONIZE_CACHE
-					even if the device claims no cache)
+					even if the device claims no cache,
+					not on uas)
 			Example: quirks=0419:aaf5:rl,0421:0433:rc
 
 	user_debug=	[KNL,ARM]

Documentation/devicetree/bindings/rtc/abracon,abx80x.txt

@@ -27,4 +27,4 @@ and valid to enable charging:
 
  - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
  - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
-                          resistor, the other values are in ohm.
+                          resistor, the other values are in kOhm.

Makefile

@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 VERSION = 4
 PATCHLEVEL = 14
-SUBLEVEL = 158
+SUBLEVEL = 159
 EXTRAVERSION =
 NAME = Petit Gorille
 
@@ -1659,9 +1659,6 @@ else # KBUILD_EXTMOD
 
 # We are always building modules
 KBUILD_MODULES := 1
-PHONY += crmodverdir
-crmodverdir:
-	$(cmd_crmodverdir)
 
 PHONY += $(objtree)/Module.symvers
 $(objtree)/Module.symvers:
@@ -1673,7 +1670,7 @@ $(objtree)/Module.symvers:
 
 module-dirs := $(addprefix _module_,$(KBUILD_EXTMOD))
 PHONY += $(module-dirs) modules
-$(module-dirs): crmodverdir $(objtree)/Module.symvers
+$(module-dirs): prepare $(objtree)/Module.symvers
 	$(Q)$(MAKE) $(build)=$(patsubst _module_%,%,$@)
 
 modules: $(module-dirs)
@@ -1714,7 +1711,8 @@ help:
 
 # Dummies...
 PHONY += prepare scripts
-prepare: ;
+prepare:
+	$(cmd_crmodverdir)
 scripts: ;
 endif # KBUILD_EXTMOD
 
@@ -1840,17 +1838,14 @@ endif
 
 # Modules
 /: prepare scripts FORCE
-	$(cmd_crmodverdir)
 	$(Q)$(MAKE) KBUILD_MODULES=$(if $(CONFIG_MODULES),1) \
 	$(build)=$(build-dir)
 # Make sure the latest headers are built for Documentation
 Documentation/ samples/: headers_install
 %/: prepare scripts FORCE
-	$(cmd_crmodverdir)
 	$(Q)$(MAKE) KBUILD_MODULES=$(if $(CONFIG_MODULES),1) \
 	$(build)=$(build-dir)
 %.ko: prepare scripts FORCE
-	$(cmd_crmodverdir)
 	$(Q)$(MAKE) KBUILD_MODULES=$(if $(CONFIG_MODULES),1)   \
 	$(build)=$(build-dir) $(@:.ko=.o)
 	$(Q)$(MAKE) -f $(srctree)/scripts/Makefile.modpost

arch/arm/Kconfig.debug

@@ -1038,14 +1038,21 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on SOCFPGA(Cyclone 5 and Arria 5) based platforms.
 
-	config DEBUG_SOCFPGA_UART1
+	config DEBUG_SOCFPGA_ARRIA10_UART1
 		depends on ARCH_SOCFPGA
-		bool "Use SOCFPGA UART1 for low-level debug"
+		bool "Use SOCFPGA Arria10 UART1 for low-level debug"
 		select DEBUG_UART_8250
 		help
 		  Say Y here if you want kernel low-level debugging support
 		  on SOCFPGA(Arria 10) based platforms.
 
+	config DEBUG_SOCFPGA_CYCLONE5_UART1
+		depends on ARCH_SOCFPGA
+		bool "Use SOCFPGA Cyclone 5 UART1 for low-level debug"
+		select DEBUG_UART_8250
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on SOCFPGA(Cyclone 5 and Arria 5) based platforms.
 
 	config DEBUG_SUN9I_UART0
 		bool "Kernel low-level debugging messages via sun9i UART0"
@@ -1600,7 +1607,8 @@ config DEBUG_UART_PHYS
 	default 0xfe800000 if ARCH_IOP32X
 	default 0xff690000 if DEBUG_RK32_UART2
 	default 0xffc02000 if DEBUG_SOCFPGA_UART0
-	default 0xffc02100 if DEBUG_SOCFPGA_UART1
+	default 0xffc02100 if DEBUG_SOCFPGA_ARRIA10_UART1
+	default 0xffc03000 if DEBUG_SOCFPGA_CYCLONE5_UART1
 	default 0xffd82340 if ARCH_IOP13XX
 	default 0xffe40000 if DEBUG_RCAR_GEN1_SCIF0
 	default 0xffe42000 if DEBUG_RCAR_GEN1_SCIF2
@@ -1704,7 +1712,8 @@ config DEBUG_UART_VIRT
 	default 0xfeb30c00 if DEBUG_KEYSTONE_UART0
 	default 0xfeb31000 if DEBUG_KEYSTONE_UART1
 	default 0xfec02000 if DEBUG_SOCFPGA_UART0
-	default 0xfec02100 if DEBUG_SOCFPGA_UART1
+	default 0xfec02100 if DEBUG_SOCFPGA_ARRIA10_UART1
+	default 0xfec03000 if DEBUG_SOCFPGA_CYCLONE5_UART1
 	default 0xfec12000 if (DEBUG_MVEBU_UART0 || DEBUG_MVEBU_UART0_ALTERNATE) && ARCH_MVEBU
 	default 0xfec12100 if DEBUG_MVEBU_UART1_ALTERNATE
 	default 0xfec10000 if DEBUG_SIRFATLAS7_UART0
@@ -1752,9 +1761,9 @@ config DEBUG_UART_8250_WORD
 	depends on DEBUG_LL_UART_8250 || DEBUG_UART_8250
 	depends on DEBUG_UART_8250_SHIFT >= 2
 	default y if DEBUG_PICOXCELL_UART || \
-		DEBUG_SOCFPGA_UART0 || DEBUG_SOCFPGA_UART1 || \
-		DEBUG_KEYSTONE_UART0 || DEBUG_KEYSTONE_UART1 || \
-		DEBUG_ALPINE_UART0 || \
+		DEBUG_SOCFPGA_UART0 || DEBUG_SOCFPGA_ARRIA10_UART1 || \
+		DEBUG_SOCFPGA_CYCLONE5_UART1 || DEBUG_KEYSTONE_UART0 || \
+		DEBUG_KEYSTONE_UART1 || DEBUG_ALPINE_UART0 || \
 		DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
 		DEBUG_DAVINCI_DA8XX_UART2 || \
 		DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2

arch/arm/boot/dts/arm-realview-pb1176.dts

@@ -45,15 +45,15 @@
 	};
 
 	/* The voltage to the MMC card is hardwired at 3.3V */
-	vmmc: fixedregulator@0 {
+	vmmc: regulator-vmmc {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmc";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
         };
 
-	veth: fixedregulator@0 {
+	veth: regulator-veth {
 		compatible = "regulator-fixed";
 		regulator-name = "veth";
 		regulator-min-microvolt = <3300000>;

arch/arm/boot/dts/arm-realview-pb11mp.dts

@@ -145,15 +145,15 @@
 	};
 
 	/* The voltage to the MMC card is hardwired at 3.3V */
-	vmmc: fixedregulator@0 {
+	vmmc: regulator-vmmc {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmc";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
         };
 
-	veth: fixedregulator@0 {
+	veth: regulator-veth {
 		compatible = "regulator-fixed";
 		regulator-name = "veth";
 		regulator-min-microvolt = <3300000>;

arch/arm/boot/dts/arm-realview-pbx.dtsi

@@ -43,15 +43,15 @@
 	};
 
 	/* The voltage to the MMC card is hardwired at 3.3V */
-	vmmc: fixedregulator@0 {
+	vmmc: regulator-vmmc {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmc";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-boot-on;
         };
 
-	veth: fixedregulator@0 {
+	veth: regulator-veth {
 		compatible = "regulator-fixed";
 		regulator-name = "veth";
 		regulator-min-microvolt = <3300000>;
@@ -539,4 +539,3 @@
 		};
 	};
 };
-

arch/arm/boot/dts/exynos3250.dtsi

@@ -359,7 +359,7 @@
 		};
 
 		hsotg: hsotg@12480000 {
-			compatible = "snps,dwc2";
+			compatible = "samsung,s3c6400-hsotg", "snps,dwc2";
 			reg = <0x12480000 0x20000>;
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_USBOTG>;

arch/arm/boot/dts/mmp2.dtsi

@@ -180,7 +180,7 @@
 				clocks = <&soc_clocks MMP2_CLK_GPIO>;
 				resets = <&soc_clocks MMP2_CLK_GPIO>;
 				interrupt-controller;
-				#interrupt-cells = <1>;
+				#interrupt-cells = <2>;
 				ranges;
 
 				gcb0: gpio@d4019000 {

arch/arm/boot/dts/omap3-pandora-common.dtsi

@@ -221,6 +221,17 @@
 		gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;	/* GPIO_164 */
 	};
 
+	/* wl1251 wifi+bt module */
+	wlan_en: fixed-regulator-wg7210_en {
+		compatible = "regulator-fixed";
+		regulator-name = "vwlan";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		startup-delay-us = <50000>;
+		enable-active-high;
+		gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+	};
+
 	/* wg7210 (wifi+bt module) 32k clock buffer */
 	wg7210_32k: fixed-regulator-wg7210_32k {
 		compatible = "regulator-fixed";
@@ -514,9 +525,30 @@
 	/*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/	/* GPIO_127 */
 };
 
-/* mmc3 is probed using pdata-quirks to pass wl1251 card data */
 &mmc3 {
-	status = "disabled";
+	vmmc-supply = <&wlan_en>;
+
+	bus-width = <4>;
+	non-removable;
+	ti,non-removable;
+	cap-power-off-card;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wlan: wifi@1 {
+		compatible = "ti,wl1251";
+
+		reg = <1>;
+
+		interrupt-parent = <&gpio1>;
+		interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;	/* GPIO_21 */
+
+		ti,wl1251-has-eeprom;
+	};
 };
 
 /* bluetooth*/

arch/arm/boot/dts/omap3-tao3530.dtsi

@@ -224,7 +224,7 @@
 	pinctrl-0 = <&mmc1_pins>;
 	vmmc-supply = <&vmmc1>;
 	vqmmc-supply = <&vsim>;
-	cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>;
 	bus-width = <8>;
 };
 

arch/arm/boot/dts/pxa27x.dtsi

@@ -35,7 +35,7 @@
 			clocks = <&clks CLK_NONE>;
 		};
 
-		pxa27x_ohci: usb@4c000000 {
+		usb0: usb@4c000000 {
 			compatible = "marvell,pxa-ohci";
 			reg = <0x4c000000 0x10000>;
 			interrupts = <3>;

arch/arm/boot/dts/pxa2xx.dtsi

@@ -117,13 +117,6 @@
 			status = "disabled";
 		};
 
-		usb0: ohci@4c000000 {
-			compatible = "marvell,pxa-ohci";
-			reg = <0x4c000000 0x10000>;
-			interrupts = <3>;
-			status = "disabled";
-		};
-
 		mmc0: mmc@41100000 {
 			compatible = "marvell,pxa-mmc";
 			reg = <0x41100000 0x1000>;

arch/arm/boot/dts/pxa3xx.dtsi

@@ -189,7 +189,7 @@
 			status = "disabled";
 		};
 
-		pxa3xx_ohci: usb@4c000000 {
+		usb0: usb@4c000000 {
 			compatible = "marvell,pxa-ohci";
 			reg = <0x4c000000 0x10000>;
 			interrupts = <3>;

arch/arm/boot/dts/rk3288-rock2-som.dtsi

@@ -63,7 +63,7 @@
 
 	vcc_flash: flash-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc_sys";
+		regulator-name = "vcc_flash";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 		startup-delay-us = <150>;

arch/arm/boot/dts/rv1108.dtsi

@@ -101,7 +101,7 @@
 
 	arm-pmu {
 		compatible = "arm,cortex-a7-pmu";
-		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
 	timer {
@@ -522,7 +522,7 @@
 			compatible = "rockchip,gpio-bank";
 			reg = <0x20030000 0x100>;
 			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&xin24m>;
+			clocks = <&cru PCLK_GPIO0_PMU>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -535,7 +535,7 @@
 			compatible = "rockchip,gpio-bank";
 			reg = <0x10310000 0x100>;
 			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&xin24m>;
+			clocks = <&cru PCLK_GPIO1>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -548,7 +548,7 @@
 			compatible = "rockchip,gpio-bank";
 			reg = <0x10320000 0x100>;
 			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&xin24m>;
+			clocks = <&cru PCLK_GPIO2>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -561,7 +561,7 @@
 			compatible = "rockchip,gpio-bank";
 			reg = <0x10330000 0x100>;
 			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&xin24m>;
+			clocks = <&cru PCLK_GPIO3>;
 
 			gpio-controller;
 			#gpio-cells = <2>;