Set XY steps to 100 for all printer models.

- X and Y steps set to 100 for all models to improve dimentional accuracy)
- Adjusted mins, maxes and probe points to compensate

config/examples/AlephObjects/standard/Gladiola_Mini/Gladiola_SingleExtruder/Configuration.h

@@ -739,7 +739,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   {100.5, 100.5, 1600, 833} // <-- changed
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100, 100, 1600, 833} // <-- changed
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -1104,15 +1104,15 @@
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 155 // <-- changed
-#define Y_BED_SIZE 155 // <-- changed
+#define X_BED_SIZE 155.8 // <-- changed
+#define Y_BED_SIZE 155.8 // <-- changed
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS 0
-#define Y_MIN_POS -8 // <-- changed
+#define X_MIN_POS 0.0 // <-- changed
+#define Y_MIN_POS -8.0 // <-- changed
 #define Z_MIN_POS -5 // <-- changed
-#define X_MAX_POS 165 // <-- changed
-#define Y_MAX_POS 195 // <-- changed
+#define X_MAX_POS 165.8 // <-- changed
+#define Y_MAX_POS 196.0 // <-- changed
 #define Z_MAX_POS 159 // <-- changed
 
 /**
@@ -1509,7 +1509,7 @@
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT {10, 185, 20} // <-- changed
+  #define NOZZLE_PARK_POINT {10, 186.0, 20} // <-- changed
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
@@ -1566,8 +1566,8 @@
 
   // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
   // Dual hotend system may use { {  -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) },  {  420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
-  #define NOZZLE_CLEAN_START_POINT {45, 174, -0.5} // <-- changed
-  #define NOZZLE_CLEAN_END_POINT   {115, 174, -0.5} // <-- changed
+  #define NOZZLE_CLEAN_START_POINT {45, 175, -0.5} // <-- changed
+  #define NOZZLE_CLEAN_END_POINT   {115, 175, -0.5} // <-- changed
 
   // Circular pattern radius
   #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
@@ -2281,7 +2281,7 @@
 //#define SHORT_BUILD_VERSION
 #define TOOLHEAD_NAME "Single Extruder" // <-- changed
 #define TOOLHEAD_TYPE "SingleExtruder" // <-- changed
-#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y174 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 Z15\nM400\nM106 S255\nG0 X0 Y168M109 R160\nM107" // <-- changed
+#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y175 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 Z15\nM400\nM106 S255\nG0 X0.0 Y168.8M109 R160\nM107" // <-- changed
 //#define AXIS_LEVELING_COMMANDS
 //#define PARK_AND_RELEASE_COMMANDS
 #define CALIBRATION_COMMANDS "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating...\nG425\nM500\nM117 Calibration data saved" // <-- changed

config/examples/AlephObjects/standard/Gladiola_Mini/Gladiola_SingleExtruder/Configuration_adv.h

@@ -1587,10 +1587,10 @@
  * the probe to be unable to reach any points.
  */
 #if PROBE_SELECTED && !IS_KINEMATIC
-  #define MIN_PROBE_EDGE_LEFT 0 // <-- changed
-  #define MIN_PROBE_EDGE_RIGHT -8 // <-- changed
-  #define MIN_PROBE_EDGE_FRONT -4 // <-- changed
-  #define MIN_PROBE_EDGE_BACK -13 // <-- changed
+  #define MIN_PROBE_EDGE_LEFT 0.0 // <-- changed
+  #define MIN_PROBE_EDGE_RIGHT -8.0 // <-- changed
+  #define MIN_PROBE_EDGE_FRONT -4.0 // <-- changed
+  #define MIN_PROBE_EDGE_BACK -13.0 // <-- changed
 #endif
 
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)

config/examples/AlephObjects/standard/Gladiola_Mini/Gladiola_SingleExtruder/Configuration_summary.txt

@@ -24,7 +24,7 @@
 #define CONTROLLER_FAN_PIN FAN1_PIN
 #define CUSTOM_MACHINE_NAME "Mini"
 #define DEFAULT_ACCELERATION 2000
-#define DEFAULT_AXIS_STEPS_PER_UNIT {100.5, 100.5, 1600, 833}
+#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 1600, 833}
 #define DEFAULT_EJERK 10.0
 #define DEFAULT_Kd 108.51
 #define DEFAULT_Ki 1.91
@@ -81,20 +81,20 @@
 #define MEASURE_BACKLASH_WHEN_PROBING
 #define MINIMUM_STEPPER_PULSE 1
 //#define MIN_PROBE_EDGE
-#define MIN_PROBE_EDGE_BACK -13
-#define MIN_PROBE_EDGE_FRONT -4
-#define MIN_PROBE_EDGE_LEFT 0
-#define MIN_PROBE_EDGE_RIGHT -8
+#define MIN_PROBE_EDGE_BACK -13.0
+#define MIN_PROBE_EDGE_FRONT -4.0
+#define MIN_PROBE_EDGE_LEFT 0.0
+#define MIN_PROBE_EDGE_RIGHT -8.0
 #define MIN_STEPS_PER_SEGMENT 6
 #define MOTHERBOARD BOARD_MINIRAMBO
 #define MULTIPLE_PROBING 2
 #define NOZZLE_AS_PROBE
-#define NOZZLE_CLEAN_END_POINT {115, 174, -0.5}
+#define NOZZLE_CLEAN_END_POINT {115, 175, -0.5}
 #define NOZZLE_CLEAN_FEATURE
 //#define NOZZLE_CLEAN_GOBACK
-#define NOZZLE_CLEAN_START_POINT {45, 174, -0.5}
+#define NOZZLE_CLEAN_START_POINT {45, 175, -0.5}
 #define NOZZLE_PARK_FEATURE
-#define NOZZLE_PARK_POINT {10, 185, 20}
+#define NOZZLE_PARK_POINT {10, 186.0, 20}
 #define NOZZLE_TO_PROBE_OFFSET {0, 0, -1.375}
 #define NO_FAN_SLOWING_IN_PID_TUNING
 #define NO_VOLUMETRICS
@@ -144,22 +144,22 @@
 #define VALIDATE_HOMING_ENDSTOPS
 #define WATCH_TEMP_INCREASE 2
 #define WATCH_TEMP_PERIOD 20
-#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y174 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 Z15\nM400\nM106 S255\nG0 X0 Y168M109 R160\nM107"
+#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y175 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 Z15\nM400\nM106 S255\nG0 X0.0 Y168.8M109 R160\nM107"
 #define XY_PROBE_SPEED 6000
-#define X_BED_SIZE 155
+#define X_BED_SIZE 155.8
 #define X_DRIVER_TYPE A4988
 #define X_HOME_DIR -1
 #define X_MAX_ENDSTOP_INVERTING 1
-#define X_MAX_POS 165
+#define X_MAX_POS 165.8
 #define X_MIN_ENDSTOP_INVERTING 1
-#define X_MIN_POS 0
-#define Y_BED_SIZE 155
+#define X_MIN_POS 0.0
+#define Y_BED_SIZE 155.8
 #define Y_DRIVER_TYPE A4988
 #define Y_HOME_DIR 1
 #define Y_MAX_ENDSTOP_INVERTING 1
-#define Y_MAX_POS 195
+#define Y_MAX_POS 196.0
 #define Y_MIN_ENDSTOP_INVERTING 1
-#define Y_MIN_POS -8
+#define Y_MIN_POS -8.0
 #define Z_CLEARANCE_BETWEEN_PROBES 5
 #define Z_CLEARANCE_DEPLOY_PROBE 5
 #define Z_DRIVER_TYPE A4988

config/examples/AlephObjects/standard/Hibiscus_Mini2/CecropiaSilk_SingleExtruderAeroV2/Configuration.h

@@ -1566,8 +1566,8 @@
 
   // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
   // Dual hotend system may use { {  -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) },  {  420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
-  #define NOZZLE_CLEAN_START_POINT {45, 174, 1} // <-- changed
-  #define NOZZLE_CLEAN_END_POINT   {115, 174, 1} // <-- changed
+  #define NOZZLE_CLEAN_START_POINT {45, 175, 1} // <-- changed
+  #define NOZZLE_CLEAN_END_POINT   {115, 175, 1} // <-- changed
 
   // Circular pattern radius
   #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
@@ -2281,7 +2281,7 @@
 //#define SHORT_BUILD_VERSION
 #define TOOLHEAD_NAME "SE 0.5mm AeroV2" // <-- changed
 #define TOOLHEAD_TYPE "SingleExtruderAeroV2" // <-- changed
-#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y174 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 Z15\nM400\nM106 S255\nG0 X-3 Y168M109 R160\nM107" // <-- changed
+#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y175 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 Z15\nM400\nM106 S255\nG0 X-3.0 Y168.8M109 R160\nM107" // <-- changed
 #define AXIS_LEVELING_COMMANDS "M117 Leveling X Axis\nG28\nG0 X150 F9999\nG0 Z5 F6000\nG91\nM211 S0\nM400\nM906 Z600\nG0 Z-15 F500\nG0 Z5 F500\nM400\nG90\nM906 Z960\nM211 S1\nG28 Z0\nM117 Leveling done." // <-- changed
 //#define PARK_AND_RELEASE_COMMANDS
 #define CALIBRATION_COMMANDS "M117 Starting Auto-Calibration\nT0\nG28\nG0 X150 F9999\nG0 Z5 F6000\nG91\nM211 S0\nM400\nM906 Z600\nG0 Z-15 F500\nG0 Z5 F500\nM400\nG90\nM906 Z960\nM211 S1\nG28 Z0\nG28\nG12\nM117 Calibrating...\nG425\nM500\nM117 Calibration data saved" // <-- changed

config/examples/AlephObjects/standard/Hibiscus_Mini2/CecropiaSilk_SingleExtruderAeroV2/Configuration_adv.h

@@ -1587,10 +1587,10 @@
  * the probe to be unable to reach any points.
  */
 #if PROBE_SELECTED && !IS_KINEMATIC
-  #define MIN_PROBE_EDGE_LEFT -3 // <-- changed
-  #define MIN_PROBE_EDGE_RIGHT -6 // <-- changed
-  #define MIN_PROBE_EDGE_FRONT -4 // <-- changed
-  #define MIN_PROBE_EDGE_BACK -11 // <-- changed
+  #define MIN_PROBE_EDGE_LEFT -3.0 // <-- changed
+  #define MIN_PROBE_EDGE_RIGHT -6.8 // <-- changed
+  #define MIN_PROBE_EDGE_FRONT -4.0 // <-- changed
+  #define MIN_PROBE_EDGE_BACK -11.8 // <-- changed
 #endif
 
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)

config/examples/AlephObjects/standard/Hibiscus_Mini2/CecropiaSilk_SingleExtruderAeroV2/Configuration_summary.txt

@@ -116,19 +116,19 @@
 //#define MENU_HOLLOW_FRAME
 #define MINIMUM_STEPPER_PULSE 1
 //#define MIN_PROBE_EDGE
-#define MIN_PROBE_EDGE_BACK -11
-#define MIN_PROBE_EDGE_FRONT -4
-#define MIN_PROBE_EDGE_LEFT -3
-#define MIN_PROBE_EDGE_RIGHT -6
+#define MIN_PROBE_EDGE_BACK -11.8
+#define MIN_PROBE_EDGE_FRONT -4.0
+#define MIN_PROBE_EDGE_LEFT -3.0
+#define MIN_PROBE_EDGE_RIGHT -6.8
 #define MIN_STEPS_PER_SEGMENT 6
 #define MONITOR_DRIVER_STATUS
 #define MOTHERBOARD BOARD_EINSY_RETRO
 #define MULTIPLE_PROBING 2
 #define NOZZLE_AS_PROBE
-#define NOZZLE_CLEAN_END_POINT {115, 174, 1}
+#define NOZZLE_CLEAN_END_POINT {115, 175, 1}
 #define NOZZLE_CLEAN_FEATURE
 //#define NOZZLE_CLEAN_GOBACK
-#define NOZZLE_CLEAN_START_POINT {45, 174, 1}
+#define NOZZLE_CLEAN_START_POINT {45, 175, 1}
 #define NOZZLE_PARK_FEATURE
 #define NOZZLE_PARK_POINT {10, 182, 20}
 #define NOZZLE_TO_PROBE_OFFSET {0, 0, -1.1}
@@ -200,7 +200,7 @@
 #define VALIDATE_HOMING_ENDSTOPS
 #define WATCH_TEMP_INCREASE 2
 #define WATCH_TEMP_PERIOD 20
-#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y174 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 X115 Y174\nG1 X45 Y174\nG1 Z15\nM400\nM106 S255\nG0 X-3 Y168M109 R160\nM107"
+#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X115 Y175 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 X115 Y175\nG1 X45 Y175\nG1 Z15\nM400\nM106 S255\nG0 X-3.0 Y168.8M109 R160\nM107"
 //#define XYZ_HOLLOW_FRAME
 #define XY_PROBE_SPEED 6000
 #define X_BED_SIZE 157

config/examples/AlephObjects/standard/Juniper_TAZ5/Tilapia_SingleExtruder/Configuration.h

@@ -739,7 +739,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   {100.5, 100.5, 1600, 830} // <-- changed
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100, 100, 1600, 830} // <-- changed
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -1104,15 +1104,15 @@
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 288 // <-- changed
-#define Y_BED_SIZE 275 // <-- changed
+#define X_BED_SIZE 289.4 // <-- changed
+#define Y_BED_SIZE 276.4 // <-- changed
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS 0
-#define Y_MIN_POS 0
+#define X_MIN_POS 0.0 // <-- changed
+#define Y_MIN_POS 0.0 // <-- changed
 #define Z_MIN_POS 0
-#define X_MAX_POS 298 // <-- changed
-#define Y_MAX_POS 276 // <-- changed
+#define X_MAX_POS 299.5 // <-- changed
+#define Y_MAX_POS 277.4 // <-- changed
 #define Z_MAX_POS 250 // <-- changed
 
 /**
@@ -1509,7 +1509,7 @@
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT {100, 275, 20} // <-- changed
+  #define NOZZLE_PARK_POINT {100, 276.4, 20} // <-- changed
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance

config/examples/AlephObjects/standard/Juniper_TAZ5/Tilapia_SingleExtruder/Configuration_summary.txt

@@ -21,7 +21,7 @@
 #define CONTROLLER_FAN_PIN FAN2_PIN
 #define CUSTOM_MACHINE_NAME "TAZ 5"
 #define DEFAULT_ACCELERATION 500
-#define DEFAULT_AXIS_STEPS_PER_UNIT {100.5, 100.5, 1600, 830}
+#define DEFAULT_AXIS_STEPS_PER_UNIT {100, 100, 1600, 830}
 #define DEFAULT_EJERK 10.0
 #define DEFAULT_Kd 108.51
 #define DEFAULT_Ki 1.91
@@ -92,7 +92,7 @@
 #define MIN_STEPS_PER_SEGMENT 6
 #define MOTHERBOARD BOARD_RAMBO
 #define NOZZLE_PARK_FEATURE
-#define NOZZLE_PARK_POINT {100, 275, 20}
+#define NOZZLE_PARK_POINT {100, 276.4, 20}
 #define NOZZLE_TO_PROBE_OFFSET {0, 0, -1.2}
 #define NO_FAN_SLOWING_IN_PID_TUNING
 #define NO_VOLUMETRICS
@@ -147,20 +147,20 @@
 #define WATCH_TEMP_INCREASE 10
 #define WATCH_TEMP_PERIOD 40
 //#define XYZ_HOLLOW_FRAME
-#define X_BED_SIZE 288
+#define X_BED_SIZE 289.4
 #define X_DRIVER_TYPE A4988
 #define X_HOME_DIR -1
 #define X_MAX_ENDSTOP_INVERTING 0
-#define X_MAX_POS 298
+#define X_MAX_POS 299.5
 #define X_MIN_ENDSTOP_INVERTING 1
-#define X_MIN_POS 0
-#define Y_BED_SIZE 275
+#define X_MIN_POS 0.0
+#define Y_BED_SIZE 276.4
 #define Y_DRIVER_TYPE A4988
 #define Y_HOME_DIR -1
 #define Y_MAX_ENDSTOP_INVERTING 1
-#define Y_MAX_POS 276
+#define Y_MAX_POS 277.4
 #define Y_MIN_ENDSTOP_INVERTING 1
-#define Y_MIN_POS 0
+#define Y_MIN_POS 0.0
 #define Z_DRIVER_TYPE A4988
 #define Z_HOME_DIR -1
 #define Z_HOMING_HEIGHT 5

config/examples/AlephObjects/standard/Oliveoil_TAZ6/Tilapia_SingleExtruder/Configuration.h

@@ -739,7 +739,7 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   {100.5, 100.5, 1600, 830} // <-- changed
+#define DEFAULT_AXIS_STEPS_PER_UNIT   {100, 100, 1600, 830} // <-- changed
 
 /**
  * Default Max Feed Rate (mm/s)
@@ -1104,15 +1104,15 @@
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 280 // <-- changed
-#define Y_BED_SIZE 280 // <-- changed
+#define X_BED_SIZE 281.4 // <-- changed
+#define Y_BED_SIZE 281.4 // <-- changed
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS -20 // <-- changed
-#define Y_MIN_POS -20 // <-- changed
+#define X_MIN_POS -20.1 // <-- changed
+#define Y_MIN_POS -20.1 // <-- changed
 #define Z_MIN_POS 0
-#define X_MAX_POS 300 // <-- changed
-#define Y_MAX_POS 303 // <-- changed
+#define X_MAX_POS 301.5 // <-- changed
+#define Y_MAX_POS 304.5 // <-- changed
 #define Z_MAX_POS 270 // <-- changed
 
 /**
@@ -1509,7 +1509,7 @@
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT {100, 302, 20} // <-- changed
+  #define NOZZLE_PARK_POINT {100, 303.5, 20} // <-- changed
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
@@ -2281,7 +2281,7 @@
 //#define SHORT_BUILD_VERSION
 #define TOOLHEAD_NAME "Single Extruder" // <-- changed
 #define TOOLHEAD_TYPE "SingleExtruder" // <-- changed
-#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X-17 Y25 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nM106 S255\nG0 X-10 Y-9M109 R160\nM107" // <-- changed
+#define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X-17 Y25 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nM106 S255\nG0 X-10.0 Y-9.0M109 R160\nM107" // <-- changed
 //#define AXIS_LEVELING_COMMANDS
 //#define PARK_AND_RELEASE_COMMANDS
 //#define CALIBRATION_COMMANDS

config/examples/AlephObjects/standard/Oliveoil_TAZ6/Tilapia_SingleExtruder/Configuration_adv.h

@@ -1587,10 +1587,10 @@
  * the probe to be unable to reach any points.
  */
 #if PROBE_SELECTED && !IS_KINEMATIC
-  #define MIN_PROBE_EDGE_LEFT -10 // <-- changed
-  #define MIN_PROBE_EDGE_RIGHT -8 // <-- changed
-  #define MIN_PROBE_EDGE_FRONT -9 // <-- changed
-  #define MIN_PROBE_EDGE_BACK -11 // <-- changed
+  #define MIN_PROBE_EDGE_LEFT -10.0 // <-- changed
+  #define MIN_PROBE_EDGE_RIGHT -8.0 // <-- changed
+  #define MIN_PROBE_EDGE_FRONT -9.0 // <-- changed
+  #define MIN_PROBE_EDGE_BACK -11.1 // <-- changed
 #endif
 
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)