Tramming Wizard

Marlin/Configuration_adv.h

@@ -808,7 +808,9 @@
 
   #define RESTORE_LEVELING_AFTER_G35    // Enable to restore leveling setup after operation
   //#define REPORT_TRAMMING_MM          // Report Z deviation (mm) for each point relative to the first
-  //#define ASSISTED_TRAMMING_MENU_ITEM // Add a menu item for Assisted Tramming
+
+  //#define ASSISTED_TRAMMING_MENU_ITEM // Add a menu item to run G35 Assisted Tramming (MarlinUI)
+  //#define ASSISTED_TRAMMING_WIZARD    // Make the menu item open a Tramming Wizard sub-menu
 
   /**
    * Screw thread:

Marlin/src/feature/tramming.h

@@ -0,0 +1,59 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <https://www.gnu.org/licenses/>.
+ *
+ */
+
+#include "../inc/MarlinConfigPre.h"
+
+#if !WITHIN(TRAMMING_SCREW_THREAD, 30, 51) || TRAMMING_SCREW_THREAD % 10 > 1
+  #error "TRAMMING_SCREW_THREAD must be equal to 30, 31, 40, 41, 50, or 51."
+#endif
+
+constexpr xy_pos_t screws_tilt_adjust_pos[] = TRAMMING_POINT_XY;
+
+#define G35_PROBE_COUNT COUNT(screws_tilt_adjust_pos)
+static_assert(G35_PROBE_COUNT >= 3, "TRAMMING_POINT_XY requires at least 3 XY positions.");
+
+extern const char point_name_1[], point_name_2[], point_name_3[]
+  #ifdef TRAMMING_POINT_NAME_4
+    , point_name_4[]
+    #ifdef TRAMMING_POINT_NAME_5
+      , point_name_5[]
+    #endif
+  #endif
+;
+
+#define _NR_TRAM_NAMES 2
+#ifdef TRAMMING_POINT_NAME_3
+  #undef _NR_TRAM_NAMES
+  #define _NR_TRAM_NAMES 3
+  #ifdef TRAMMING_POINT_NAME_4
+    #undef _NR_TRAM_NAMES
+    #define _NR_TRAM_NAMES 4
+    #ifdef TRAMMING_POINT_NAME_5
+      #undef _NR_TRAM_NAMES
+      #define _NR_TRAM_NAMES 5
+    #endif
+  #endif
+#endif
+static_assert(_NR_TRAM_NAMES >= G35_PROBE_COUNT, "Define enough TRAMMING_POINT_NAME_s for all TRAMMING_POINT_XY entries.");
+#undef _NR_TRAM_NAMES
+
+extern PGM_P const tramming_point_name[];

Marlin/src/gcode/bedlevel/G35.cpp

@@ -36,19 +36,23 @@
 #define DEBUG_OUT ENABLED(DEBUG_LEVELING_FEATURE)
 #include "../../core/debug_out.h"
 
-constexpr xy_pos_t screws_tilt_adjust_pos[] = TRAMMING_POINT_XY;
+//
+// Define tramming point names.
+//
 
-static PGMSTR(point_name_1, TRAMMING_POINT_NAME_1);
-static PGMSTR(point_name_2, TRAMMING_POINT_NAME_2);
-static PGMSTR(point_name_3, TRAMMING_POINT_NAME_3);
+#include "../../feature/tramming.h" // Validate
+
+PGMSTR(point_name_1, TRAMMING_POINT_NAME_1);
+PGMSTR(point_name_2, TRAMMING_POINT_NAME_2);
+PGMSTR(point_name_3, TRAMMING_POINT_NAME_3);
 #ifdef TRAMMING_POINT_NAME_4
-  static PGMSTR(point_name_4, TRAMMING_POINT_NAME_4);
+  PGMSTR(point_name_4, TRAMMING_POINT_NAME_4);
   #ifdef TRAMMING_POINT_NAME_5
-    static PGMSTR(point_name_5, TRAMMING_POINT_NAME_5);
+    PGMSTR(point_name_5, TRAMMING_POINT_NAME_5);
   #endif
 #endif
 
-static PGM_P const tramming_point_name[] PROGMEM = {
+PGM_P const tramming_point_name[] PROGMEM = {
   point_name_1, point_name_2, point_name_3
   #ifdef TRAMMING_POINT_NAME_4
     , point_name_4
@@ -58,14 +62,6 @@ static PGM_P const tramming_point_name[] PROGMEM = {
   #endif
 };
 
-#define G35_PROBE_COUNT COUNT(screws_tilt_adjust_pos)
-
-#if !WITHIN(TRAMMING_SCREW_THREAD, 30, 51) || TRAMMING_SCREW_THREAD % 10 > 1
-  #error "TRAMMING_SCREW_THREAD must be equal to 30, 31, 40, 41, 50, or 51."
-#endif
-
-static_assert(G35_PROBE_COUNT > 2, "TRAMMING_POINT_XY requires at least 3 XY positions.");
-
 /**
  * G35: Read bed corners to help adjust bed screws
  *

Marlin/src/lcd/language/language_en.h

@@ -73,7 +73,6 @@ namespace Language_en {
   PROGMEM Language_Str MSG_AUTO_HOME_Y                     = _UxGT("Home Y");
   PROGMEM Language_Str MSG_AUTO_HOME_Z                     = _UxGT("Home Z");
   PROGMEM Language_Str MSG_AUTO_Z_ALIGN                    = _UxGT("Auto Z-Align");
-  PROGMEM Language_Str MSG_ASSISTED_TRAMMING               = _UxGT("Assisted Tramming");
   PROGMEM Language_Str MSG_ITERATION                       = _UxGT("G34 Iteration: %i");
   PROGMEM Language_Str MSG_DECREASING_ACCURACY             = _UxGT("Accuracy Decreasing!");
   PROGMEM Language_Str MSG_ACCURACY_ACHIEVED               = _UxGT("Accuracy Achieved");
@@ -85,6 +84,10 @@ namespace Language_en {
   PROGMEM Language_Str MSG_SET_HOME_OFFSETS                = _UxGT("Set Home Offsets");
   PROGMEM Language_Str MSG_HOME_OFFSETS_APPLIED            = _UxGT("Offsets Applied");
   PROGMEM Language_Str MSG_SET_ORIGIN                      = _UxGT("Set Origin");
+  PROGMEM Language_Str MSG_ASSISTED_TRAMMING               = _UxGT("Assisted Tramming");
+  PROGMEM Language_Str MSG_TRAMMING_WIZARD                 = _UxGT("Tramming Wizard");
+  PROGMEM Language_Str MSG_SELECT_ORIGIN                   = _UxGT("Select Origin");
+  PROGMEM Language_Str MSG_LAST_VALUE_SP                   = _UxGT("Last value ");
   #if PREHEAT_COUNT
     PROGMEM Language_Str MSG_PREHEAT_1                     = _UxGT("Preheat ") PREHEAT_1_LABEL;
     PROGMEM Language_Str MSG_PREHEAT_1_H                   = _UxGT("Preheat ") PREHEAT_1_LABEL " ~";
@@ -666,6 +669,7 @@ namespace Language_en {
   PROGMEM Language_Str MSG_REHEATING                       = _UxGT("Reheating...");
 
   PROGMEM Language_Str MSG_PROBE_WIZARD                    = _UxGT("Z Probe Wizard");
+
   PROGMEM Language_Str MSG_SOUND                           = _UxGT("Sound");
 }
 

Marlin/src/lcd/menu/menu_motion.cpp

@@ -305,6 +305,10 @@ void menu_move() {
   void menu_bed_leveling();
 #endif
 
+#if ENABLED(ASSISTED_TRAMMING_WIZARD)
+  void goto_tramming_wizard();
+#endif
+
 void menu_motion() {
   START_MENU();
 
@@ -346,7 +350,9 @@ void menu_motion() {
   //
   // Assisted Bed Tramming
   //
-  #if ENABLED(ASSISTED_TRAMMING_MENU_ITEM)
+  #if ENABLED(ASSISTED_TRAMMING_WIZARD)
+    SUBMENU(MSG_TRAMMING_WIZARD, goto_tramming_wizard);
+  #elif ENABLED(ASSISTED_TRAMMING_MENU_ITEM)
     GCODES_ITEM(MSG_ASSISTED_TRAMMING, PSTR("G35"));
   #endif
 

Marlin/src/lcd/menu/menu_tramming.cpp

@@ -0,0 +1,93 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+//
+// Bed Tramming Wizard
+//
+
+#include "../../inc/MarlinConfigPre.h"
+
+#if BOTH(HAS_LCD_MENU, ASSISTED_TRAMMING_WIZARD)
+
+#include "menu_item.h"
+
+#include "../../feature/tramming.h"
+
+#include "../../module/motion.h"
+#include "../../module/probe.h"
+#include "../../gcode/queue.h"
+
+//#define DEBUG_OUT 1
+#include "../../core/debug_out.h"
+
+float z_measured[G35_PROBE_COUNT] = { 0 };
+static uint8_t tram_index = 0;
+
+bool probe_single_point() {
+  const float z_probed_height = probe.probe_at_point(screws_tilt_adjust_pos[tram_index], PROBE_PT_RAISE, 0, true);
+  DEBUG_ECHOLNPAIR("probe_single_point: ", z_probed_height, "mm");
+  z_measured[tram_index] = z_probed_height;
+  return !isnan(z_probed_height);
+}
+
+void _menu_single_probe(const uint8_t point) {
+  tram_index = point;
+  DEBUG_ECHOLNPAIR("Screen: single probe screen Arg:", point);
+  START_MENU();
+  STATIC_ITEM(MSG_LEVEL_CORNERS, SS_LEFT);
+  STATIC_ITEM(MSG_LAST_VALUE_SP, SS_LEFT, ftostr42_52(z_measured[0] - z_measured[point])); // Print diff
+  ACTION_ITEM(MSG_UBL_BC_INSERT2, []{ if (probe_single_point()) ui.refresh(); });
+  ACTION_ITEM(MSG_BUTTON_DONE, []{ ui.goto_previous_screen_no_defer(); }); // Back
+  END_MENU();
+}
+
+void tramming_wizard_menu() {
+  DEBUG_ECHOLNPAIR("Screen: tramming_wizard_menu");
+  START_MENU();
+  STATIC_ITEM(MSG_SELECT_ORIGIN);
+
+  // Draw a menu item for each tramming point
+  LOOP_L_N(i, G35_PROBE_COUNT)
+    SUBMENU_N_P(i, tramming_point_name[i], []{ _menu_single_probe(MenuItemBase::itemIndex); });
+
+  ACTION_ITEM(MSG_BUTTON_DONE, []{ ui.goto_previous_screen_no_defer(); });
+  END_MENU();
+}
+
+// Init the wizard and enter the submenu
+void goto_tramming_wizard() {
+  DEBUG_ECHOLNPAIR("Screen: goto_tramming_wizard", 1);
+  tram_index = 0;
+  ui.defer_status_screen();
+  //probe_single_point(); // Probe first point to get differences
+
+  // Inject G28, wait for homing to complete,
+  set_all_unhomed();
+  queue.inject_P(G28_STR);
+  ui.goto_screen([]{
+    _lcd_draw_homing();
+    if (all_axes_homed())
+      ui.goto_screen(tramming_wizard_menu);
+  });
+}
+
+#endif // HAS_LCD_MENU && ASSISTED_TRAMMING_WIZARD

buildroot/share/PlatformIO/scripts/common-dependencies.h

@@ -111,6 +111,9 @@
   #if ENABLED(TOUCH_SCREEN_CALIBRATION)
     #define HAS_MENU_TOUCH_SCREEN
   #endif
+  #if ENABLED(ASSISTED_TRAMMING_WIZARD)
+    #define HAS_MENU_TRAMMING
+  #endif
   #if ENABLED(AUTO_BED_LEVELING_UBL)
     #define HAS_MENU_UBL
   #endif

buildroot/tests/DUE-tests

@@ -14,7 +14,7 @@ opt_set TEMP_SENSOR_BED 2
 opt_set GRID_MAX_POINTS_X 16
 opt_set FANMUX0_PIN 53
 opt_enable S_CURVE_ACCELERATION EEPROM_SETTINGS GCODE_MACROS \
-           FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING ASSISTED_TRAMMING \
+           FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING ASSISTED_TRAMMING ASSISTED_TRAMMING_WIZARD \
            EEPROM_SETTINGS SDSUPPORT BINARY_FILE_TRANSFER \
            BLINKM PCA9533 PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \
            NEOPIXEL_LED CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CASE_LIGHT_MENU \

platformio.ini

@@ -48,6 +48,7 @@ default_src_filter = +<src/*> -<src/config> -<src/HAL> +<src/HAL/shared>
   -<src/lcd/menu/menu_temperature.cpp>
   -<src/lcd/menu/menu_tmc.cpp>
   -<src/lcd/menu/menu_touch_screen.cpp>
+  -<src/lcd/menu/menu_tramming.cpp>
   -<src/lcd/menu/menu_ubl.cpp>
   -<src/lcd/extui/lib/mks_ui>
   -<src/lcd/extui/lib/dgus> -<src/lcd/extui/dgus_lcd.cpp>
@@ -259,6 +260,7 @@ HAS_MENU_CUTTER         = src_filter=+<src/lcd/menu/menu_spindle_laser.cpp>
 HAS_MENU_TEMPERATURE    = src_filter=+<src/lcd/menu/menu_temperature.cpp>
 HAS_MENU_TMC            = src_filter=+<src/lcd/menu/menu_tmc.cpp>
 HAS_MENU_TOUCH_SCREEN   = src_filter=+<src/lcd/menu/menu_touch_screen.cpp>
+HAS_MENU_TRAMMING       = src_filter=+<src/lcd/menu/menu_tramming.cpp>
 HAS_MENU_UBL            = src_filter=+<src/lcd/menu/menu_ubl.cpp>
 ANYCUBIC_LCD_CHIRON     = src_filter=+<src/lcd/extui/anycubic_chiron_lcd.cpp> +<src/lcd/extui/lib/anycubic_chiron>
 ANYCUBIC_LCD_I3MEGA     = src_filter=+<src/lcd/extui/anycubic_i3mega_lcd.cpp> +<src/lcd/extui/lib/anycubic_i3mega>