This repository is deprecated. Use the ModusToolbox™ example available here - https://github.com/Infineon/mtb-example-usb-device-hid-generic

PSoC™ 6 MCU: USB HID generic application

This example demonstrates how to configure the USB block in a PSoC™ 6 MCU as a Human Interface Device (HID). The device enumerates as a generic HID device.

View this README on GitHub.

Provide feedback on this code example.

Requirements

• ModusToolbox™ software v2.2 or later (tested with v2.3)
• Board support package (BSP) minimum required version: 2.0.0
• Programming language: C
• Associated parts: All PSoC™ 6 MCU parts

Supported toolchains (make variable 'TOOLCHAIN')

• GNU Arm® embedded compiler v9.3.1 (GCC_ARM) - Default value of TOOLCHAIN
• Arm® compiler v6.13 (ARM)
• IAR C/C++ compiler v8.42.2 (IAR)

Supported kits (make variable 'TARGET')

• PSoC™ 6 Wi-Fi Bluetooth® prototyping kit (CY8CPROTO-062-4343W) - Default value of TARGET
• PSoC™ 6 Wi-Fi Bluetooth® pioneer kit (CY8CKIT-062-WIFI-BT)
• PSoC™ 62S2 Wi-Fi Bluetooth® pioneer kit (CY8CKIT-062S2-43012)
• PSoC™ 62S1 Wi-Fi Bluetooth® pioneer kit (CYW9P62S1-43438EVB-01)
• PSoC™ 62S1 Wi-Fi Bluetooth® pioneer kit (CYW9P62S1-43012EVB-01)
• PSoC™ 62S3 Wi-Fi Bluetooth® prototyping kit (CY8CPROTO-062S3-4343W)
• PSoC™ 64 "Secure Boot" Wi-Fi Bluetooth® pioneer kit (CY8CKIT-064B0S2-4343W)
• PSoC™ 62S2 evaluation kit (CY8CEVAL-062S2, CY8CEVAL-062S2-LAI-4373M2)

Hardware setup

This example uses the board's default configuration. See the kit user guide to ensure that the board is configured correctly.

Note: The PSoC™ 6 Bluetooth® LE pioneer kit (CY8CKIT-062-BLE) and the PSoC™ 6 Wi-Fi Bluetooth® pioneer kit (CY8CKIT-062-WIFI-BT) ship with KitProg2 installed. The ModusToolbox™ software requires KitProg3. Before using this code example, make sure that the board is upgraded to KitProg3. The tool and instructions are available in the Firmware Loader GitHub repository. If you do not upgrade, you will see an error like "unable to find CMSIS-DAP device" or "KitProg firmware is out of date".

Software setup

This example requires a USB host tool to write and read data to/from a HID device. Instructions in this document use this USB-HID tool.

Download the GitHub project available in this link. You should see a /bin folder that contains the usbhidtool executable available for different systems.

Using the code example

Create the project and open it using one of the following:

In Eclipse IDE for ModusToolbox™ software

1. Click the New Application link in the Quick Panel (or, use File > New > ModusToolbox Application). This launches the Project Creator tool.

2. Pick a kit supported by the code example from the list shown in the Project Creator - Choose Board Support Package (BSP) dialog.

   When you select a supported kit, the example is reconfigured automatically to work with the kit. To work with a different supported kit later, use the Library Manager to choose the BSP for the supported kit. You can use the Library Manager to select or update the BSP and firmware libraries used in this application. To access the Library Manager, click the link from the Quick Panel.

   You can also just start the application creation process again and select a different kit.

   If you want to use the application for a kit not listed here, you may need to update the source files. If the kit does not have the required resources, the application may not work.

3. In the Project Creator - Select Application dialog, choose the example by enabling the checkbox.

4. (Optional) Change the suggested New Application Name.

5. The Application(s) Root Path defaults to the Eclipse workspace which is usually the desired location for the application. If you want to store the application in a different location, you can change the Application(s) Root Path value. Applications that share libraries should be in the same root path.

6. Click Create to complete the application creation process.

For more details, see the Eclipse IDE for ModusToolbox™ software user guide (locally available at {ModusToolbox™ software install directory}/ide_{version}/docs/mt_ide_user_guide.pdf).

In command-line interface (CLI)

ModusToolbox™ software provides the Project Creator as both a GUI tool and the command line tool, "project-creator-cli". The CLI tool can be used to create applications from a CLI terminal or from within batch files or shell scripts. This tool is available in the {ModusToolbox™ software install directory}/tools_{version}/project-creator/ directory.

Use a CLI terminal to invoke the "project-creator-cli" tool. On Windows, use the command line "modus-shell" program provided in the ModusToolbox™ software installation instead of a standard Windows command-line application. This shell provides access to all ModusToolbox™ software tools. You can access it by typing modus-shell in the search box in the Windows menu. In Linux and macOS, you can use any terminal application.

This tool has the following arguments:

Argument	Description	Required/optional
--board-id	Defined in the <id> field of the BSP manifest	Required
--app-id	Defined in the <id> field of the CE manifest	Required
--target-dir	Specify the directory in which the application is to be created if you prefer not to use the default current working directory	Optional
--user-app-name	Specify the name of the application if you prefer to have a name other than the example's default name	Optional

The following example will clone the "Hello World" application with the desired name "MyHelloWorld" configured for the CY8CKIT-062-WIFI-BT BSP into the specified working directory, C:/mtb_projects:

project-creator-cli --board-id CY8CKIT-062-WIFI-BT --app-id mtb-example-psoc6-hello-world --user-app-name MyHelloWorld --target-dir "C:/mtb_projects"

Note: The project-creator-cli tool uses the git clone and make getlibs commands to fetch the repository and import the required libraries. For details, see the "Project creator tools" section of the ModusToolbox™ software user guide (locally available at {ModusToolbox™ software install directory}/docs_{version}/mtb_user_guide.pdf).

In third-party IDEs

Use one of the following options:

• Use the standalone Project Creator tool:

  1. Launch Project Creator from the Windows Start menu or from {ModusToolbox™ software install directory}/tools_{version}/project-creator/project-creator.exe.

  2. In the initial Choose Board Support Package screen, select the BSP, and click Next.

  3. In the Select Application screen, select the appropriate IDE from the Target IDE drop-down menu.

  4. Click Create and follow the instructions printed in the bottom pane to import or open the exported project in the respective IDE.

• Use command-line interface (CLI):

  1. Follow the instructions from the In command-line interface (CLI) section to create the application, and then import the libraries using the make getlibs command.

  2. Export the application to a supported IDE using the make <ide> command.

  3. Follow the instructions displayed in the terminal to create or import the application as an IDE project.

For a list of supported IDEs and more details, see the "Exporting to IDEs" section of the ModusToolbox™ software user guide (locally available at {ModusToolbox™ software install directory}/docs_{version}/mtb_user_guide.pdf).

Operation

If using a PSoC™ 64 "Secure Boot" MCU kit (like CY8CKIT-064B0S2-4343W), the PSoC™ 64 device must be provisioned with keys and policies before being programmed. Follow the instructions in the "Secure Boot" SDK user guide to provision the device. If the kit is already provisioned, copy-paste the keys and policy folder to the application folder.

1. Connect the board to your PC using the provided USB cable through the KitProg3 USB connector.

2. Open a terminal program and select the KitProg3 COM port. Set the serial port parameters to 8N1 and 115200 baud.

3. Program the board using one of the following:

   Using Eclipse IDE for ModusToolbox™ software

   1. Select the application project in the Project Explorer.

   2. In the Quick Panel, scroll down, and click <Application Name> Program (KitProg3_MiniProg4).

   Using CLI

   From the terminal, execute the make program command to build and program the application using the default toolchain to the default target. The default toolchain and target are specified in the application's Makefile but you can override those values manually:

   make program TARGET=<BSP> TOOLCHAIN=<toolchain>
   

   Example:

   make program TARGET=CY8CPROTO-062-4343W TOOLCHAIN=GCC_ARM
   

4. Connect another USB cable (or reuse the same cable used to program the kit) to the USB device connector (See the kit user guide for its location). Check if the user LED turns ON after enumeration.

5. On the computer, open a terminal console and run the usbhidtool to send a few bytes. The tool requires as argument the VID, PID, number of bytes to send, and data. See the USB-HID tool documentation or use the following example:

   In Windows:

   usbhidtool.exe 0x04B4 0xE17E 4 0xDE 0xAD 0xBE 0xEF
   

   In Linux:

   ./usbhidtool 0x04B4 0xE17E 4 0xDE 0xAD 0xBE 0xEF
   

6. After writing to the device, you should see the same data written back to the terminal console.

   de ad be ef 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
   

Note: The usbhidtool always sends 64 bytes to the device, independent of how many bytes provided. Any remaining data is written with zeros.

Debugging

You can debug the example to step through the code. In the IDE, use the <Application Name> Debug (KitProg3_MiniProg4) configuration in the Quick Panel. For details, see the "Program and debug" section in the Eclipse IDE for ModusToolbox™ software user guide.

Note: (Only while debugging) On the CM4 CPU, some code in main() may execute before the debugger halts at the beginning of main(). This means that some code executes twice – once before the debugger stops execution, and again after the debugger resets the program counter to the beginning of main(). See KBA231071 to learn about this and for the workaround.

Design and implementation

In the main firmware routine, the USB Device block is configured to use the HID Device class. After enumeration, the device turns ON the user LED and continuously checks for data to read. If data is available, the application copies the available data to a local buffer, and then writes the same data back to the USB host. The read and write USB functions used in this example are blocking. The user LED briefly turns OFF when receiving/sending data. The device goes to sleep when no data is available.

To see the generic 64-byte HID descriptor, use the usbdev-configurator tool located at <ModusToolbox_install_dir>/tools_<version>/usbdev-configurator. In the tool, open the design.cyusbdev file located under the /COMPONENT_CUSTOM_DESIGN_MODUS/TARGET_<BSP> folder.

Resources and settings

Table 1. Application resources

Resource	Alias/object	Purpose
USBDEV (PDL)	CYBSP_USBDEV	USB device configured with HID 64-byte generic descriptor
GPIO (HAL)	CYBSP_USER_LED	Indicates when transmitting data

Related resources

Resources	Links
Application notes	AN228571 – Getting started with PSoC™ 6 MCU on ModusToolbox™ software AN215656 – PSoC™ 6 MCU: Dual-CPU system design
Code examples on GitHub	mtb-example-psoc6-* – PSoC™ 6 MCU examples
Device documentation	PSoC™ 6 MCU datasheets PSoC™ 6 technical reference manuals
Development kits	Visit www.cypress.com/microcontrollers-mcus-kits and use the options in the Select your kit section to filter kits by Product family or Features.
Libraries on GitHub	mtb-pdl-cat1 – PSoC™ 6 peripheral driver library (PDL) and docs mtb-hal-cat1 – Hardware abstraction layer (HAL) Library and docs retarget-io – Retarget-IO - A utility library to retarget the standard input/output (STDIO) messages to a UART port
Middleware on GitHub	capsense – CAPSENSE™ library and documents psoc6-middleware – Links to all PSoC™ 6 MCU middleware
Tools	Eclipse IDE for ModusToolbox™ software – ModusToolbox™ software is a collection of easy-to-use software and tools enabling rapid development with Infineon® MCUs, covering applications from embedded sense and control to wireless and cloud-connected systems using AIROC™ Wi-Fi and Bluetooth® connectivity devices.

Other resources

Cypress provides a wealth of data at www.cypress.com to help you select the right device, and quickly and effectively integrate it into your design.

For PSoC™ 6 MCU devices, see How to design with PSoC™ 6 MCU - KBA223067 in the Cypress community.

Document history

Document title: CE229111 - PSoC™ 6 MCU: USB HID generic application

Version	Description of change
1.0.0	New code example
1.1.0	Updated to support ModusToolbox™ software v2.1 Added support to new kits
2.0.0	Major update to support ModusToolbox™ software v2.2, added support for new kits This version is not backward compatible with ModusToolbox software v2.1
2.1.0	Updated to support ModusToolbox™ software v2.3 Added support for CY8CEVAL-062S2, CY8CEVAL-062S2-LAI-4373M2

---------------------------------------------------------

© Cypress Semiconductor Corporation, 2020-2021. This document is the property of Cypress Semiconductor Corporation, an Infineon Technologies company, and its affiliates ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress’s patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress shall have no liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. CYPRESS DOES NOT REPRESENT, WARRANT, OR GUARANTEE THAT CYPRESS PRODUCTS, OR SYSTEMS CREATED USING CYPRESS PRODUCTS, WILL BE FREE FROM CORRUPTION, ATTACK, VIRUSES, INTERFERENCE, HACKING, DATA LOSS OR THEFT, OR OTHER SECURITY INTRUSION (collectively, "Security Breach"). Cypress disclaims any liability relating to any Security Breach, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any Security Breach. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. "High-Risk Device" means any device or system whose failure could cause personal injury, death, or property damage. Examples of High-Risk Devices are weapons, nuclear installations, surgical implants, and other medical devices. "Critical Component" means any component of a High-Risk Device whose failure to perform can be reasonably expected to cause, directly or indirectly, the failure of the High-Risk Device, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from any use of a Cypress product as a Critical Component in a High-Risk Device. You shall indemnify and hold Cypress, including its affiliates, and its directors, officers, employees, agents, distributors, and assigns harmless from and against all claims, costs, damages, and expenses, arising out of any claim, including claims for product liability, personal injury or death, or property damage arising from any use of a Cypress product as a Critical Component in a High-Risk Device. Cypress products are not intended or authorized for use as a Critical Component in any High-Risk Device except to the limited extent that (i) Cypress’s published data sheet for the product explicitly states Cypress has qualified the product for use in a specific High-Risk Device, or (ii) Cypress has given you advance written authorization to use the product as a Critical Component in the specific High-Risk Device and you have signed a separate indemnification agreement.
Cypress, the Cypress logo, and combinations thereof, WICED, ModusToolbox, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress or a subsidiary of Cypress in the United States or in other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.