Singleton for cutting tools (MarlinFirmware#14429)

Glodigit · Jun 28, 2019 · d7d8041 · d7d8041
1 parent 2fde147
commit d7d8041
Show file tree

Hide file tree

Showing 127 changed files with 2,773 additions and 2,675 deletions.
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
@@ -2121,36 +2121,38 @@
  *
  * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  */
-//#define SPINDLE_LASER_ENABLE
-#if ENABLED(SPINDLE_LASER_ENABLE)
-
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // Set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // Set to true if your controller supports setting the speed/power
+//#define SPINDLE_FEATURE
+//#define LASER_FEATURE
+#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
+  #define SPINDLE_LASER_ACTIVE_HIGH     false  // Set to "true" if the on/off function is active HIGH
+  #define SPINDLE_LASER_PWM             true   // Set to "true" if your controller supports setting the speed/power
   #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
   #define SPINDLE_LASER_POWERUP_DELAY   5000   // (ms) Delay to allow the spindle/laser to come up to speed/power
   #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // (ms) Delay to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // Set to true if your spindle controller supports changing spindle direction
-  #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // Set to true if Marlin should stop the spindle before changing rotation direction
-
-  /**
-   *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
-   *
-   *  SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
-   *    where PWM duty cycle varies from 0 to 255
-   *
-   *  set the following for your controller (ALL MUST BE SET)
-   */
 
-  #define SPEED_POWER_SLOPE    118.4
-  #define SPEED_POWER_INTERCEPT  0
-  #define SPEED_POWER_MIN     5000
-  #define SPEED_POWER_MAX    30000    // SuperPID router controller 0 - 30,000 RPM
+  #if ENABLED(SPINDLE_FEATURE)
+    //#define SPINDLE_CHANGE_DIR               // Enable if your spindle controller can change spindle direction
+    #define SPINDLE_CHANGE_DIR_STOP            // Enable if the spindle should stop before changing spin direction
+    #define SPINDLE_INVERT_DIR          false  // Set to "true" if the spin direction is reversed
 
-  //#define SPEED_POWER_SLOPE      0.3922
-  //#define SPEED_POWER_INTERCEPT  0
-  //#define SPEED_POWER_MIN       10
-  //#define SPEED_POWER_MAX      100      // 0-100%
+    /**
+     *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
+     *
+     *  SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
+     *    where PWM duty cycle varies from 0 to 255
+     *
+     *  set the following for your controller (ALL MUST BE SET)
+     */
+    #define SPEED_POWER_SLOPE    118.4
+    #define SPEED_POWER_INTERCEPT  0
+    #define SPEED_POWER_MIN     5000
+    #define SPEED_POWER_MAX    30000    // SuperPID router controller 0 - 30,000 RPM
+  #else
+    #define SPEED_POWER_SLOPE      0.3922
+    #define SPEED_POWER_INTERCEPT  0
+    #define SPEED_POWER_MIN       10
+    #define SPEED_POWER_MAX      100    // 0-100%
+  #endif
 #endif
 
 /**

diff --git a/Marlin/src/HAL/HAL_AVR/SanityCheck.h b/Marlin/src/HAL/HAL_AVR/SanityCheck.h
@@ -22,7 +22,7 @@
 #pragma once
 
 /**
- * Test AVR specific configuration values for errors at compile-time.
+ * Test AVR-specific configuration values for errors at compile-time.
  */
 
 /**
@@ -43,65 +43,15 @@
 #endif
 
 /**
- * Sanity checks for Spindle / Laser
+ * Sanity checks for Spindle / Laser PWM
  */
-#if ENABLED(SPINDLE_LASER_ENABLE)
-  #if !PIN_EXISTS(SPINDLE_LASER_ENA)
-    #error "SPINDLE_LASER_ENABLE requires SPINDLE_LASER_ENA_PIN."
-  #elif SPINDLE_DIR_CHANGE && !PIN_EXISTS(SPINDLE_DIR)
-    #error "SPINDLE_DIR_PIN not defined."
-  #elif ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
-    #if !(WITHIN(SPINDLE_LASER_PWM_PIN, 2, 13) || WITHIN(SPINDLE_LASER_PWM_PIN, 44, 46))
-      #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin."
-    #elif SPINDLE_LASER_POWERUP_DELAY < 1
-      #error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0."
-    #elif SPINDLE_LASER_POWERDOWN_DELAY < 1
-      #error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0."
-    #elif !defined(SPINDLE_LASER_PWM_INVERT)
-      #error "SPINDLE_LASER_PWM_INVERT missing."
-    #elif !defined(SPEED_POWER_SLOPE) || !defined(SPEED_POWER_INTERCEPT) || !defined(SPEED_POWER_MIN) || !defined(SPEED_POWER_MAX)
-      #error "SPINDLE_LASER_PWM equation constant(s) missing."
-    #elif SPINDLE_LASER_PWM_PIN == 4 || WITHIN(SPINDLE_LASER_PWM_PIN, 11, 13)
-      #error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by a system interrupt."
-    #elif PIN_EXISTS(X_MAX) && X_MAX_PIN == SPINDLE_LASER_PWM_PIN
-      #error "SPINDLE_LASER_PWM pin is in use by X_MAX endstop."
-    #elif PIN_EXISTS(X_MIN) && X_MIN_PIN == SPINDLE_LASER_PWM_PIN
-      #error "SPINDLE_LASER_PWM pin is in use by X_MIN endstop."
-    #elif PIN_EXISTS(Z_STEP) && Z_STEP_PIN == SPINDLE_LASER_PWM_PIN
-      #error "SPINDLE_LASER_PWM pin in use by Z_STEP."
-    #elif NUM_SERVOS > 0 && (WITHIN(SPINDLE_LASER_PWM_PIN, 2, 3) || SPINDLE_LASER_PWM_PIN == 5)
-      #error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by the servo system."
-    #elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT_PIN."
-    #elif PIN_EXISTS(E0_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E0_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E0_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E1_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E1_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E1_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E2_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E2_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E2_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E3_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E3_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E5_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E5_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E5_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by FAN_PIN."
-    #elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by FAN1_PIN."
-    #elif PIN_EXISTS(FAN2) && SPINDLE_LASER_PWM_PIN == FAN2_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by FAN2_PIN."
-    #elif PIN_EXISTS(CONTROLLERFAN) && SPINDLE_LASER_PWM_PIN == CONTROLLERFAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CONTROLLERFAN_PIN."
-    #elif PIN_EXISTS(MOTOR_CURRENT_PWM_XY) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_XY_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_XY."
-    #elif PIN_EXISTS(MOTOR_CURRENT_PWM_Z) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_Z_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_Z."
-    #elif PIN_EXISTS(MOTOR_CURRENT_PWM_E) && SPINDLE_LASER_PWM_PIN == MOTOR_CURRENT_PWM_E_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by MOTOR_CURRENT_PWM_E."
-    #endif
+#if ENABLED(SPINDLE_LASER_PWM)
+  #if SPINDLE_LASER_PWM_PIN == 4 || WITHIN(SPINDLE_LASER_PWM_PIN, 11, 13)
+    #error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by a system interrupt."
+  #elif NUM_SERVOS > 0 && (WITHIN(SPINDLE_LASER_PWM_PIN, 2, 3) || SPINDLE_LASER_PWM_PIN == 5)
+    #error "Counter/Timer for SPINDLE_LASER_PWM_PIN is used by the servo system."
   #endif
-#endif // SPINDLE_LASER_ENABLE
+#endif
 
 /**
  * The Trinamic library includes SoftwareSerial.h, leading to a compile error.

diff --git a/Marlin/src/HAL/HAL_LINUX/SanityCheck.h b/Marlin/src/HAL/HAL_LINUX/SanityCheck.h
@@ -21,50 +21,13 @@
  */
 
 /**
- * Test X86_64 configuration values for errors at compile-time.
+ * Test X86_64-specific configuration values for errors at compile-time.
  */
 
-#if ENABLED(SPINDLE_LASER_ENABLE)
-  #if !PIN_EXISTS(SPINDLE_LASER_ENA)
-    #error "SPINDLE_LASER_ENABLE requires SPINDLE_LASER_ENA_PIN."
-  #elif SPINDLE_DIR_CHANGE && !PIN_EXISTS(SPINDLE_DIR)
-    #error "SPINDLE_DIR_PIN not defined."
-  #elif ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
-    #if !PWM_PIN(SPINDLE_LASER_PWM_PIN)
-      #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin."
-    #elif !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11)
-      #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector"
-    #elif SPINDLE_LASER_POWERUP_DELAY < 1
-      #error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0."
-    #elif SPINDLE_LASER_POWERDOWN_DELAY < 1
-      #error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0."
-    #elif !defined(SPINDLE_LASER_PWM_INVERT)
-      #error "SPINDLE_LASER_PWM_INVERT missing."
-    #elif !defined(SPEED_POWER_SLOPE) || !defined(SPEED_POWER_INTERCEPT) || !defined(SPEED_POWER_MIN) || !defined(SPEED_POWER_MAX)
-      #error "SPINDLE_LASER_PWM equation constant(s) missing."
-    #elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT_PIN."
-    #elif PIN_EXISTS(E0_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E0_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E0_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E1_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E1_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E1_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E2_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E2_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E2_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E3_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E3_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
-    #elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN1_PIN."
-    #elif PIN_EXISTS(FAN2) && SPINDLE_LASER_PWM_PIN == FAN2_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN2_PIN."
-    #elif PIN_EXISTS(CONTROLLERFAN) && SPINDLE_LASER_PWM_PIN == CONTROLLERFAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CONTROLLERFAN_PIN."
-    #endif
-  #endif
-#endif // SPINDLE_LASER_ENABLE
+// Emulating RAMPS
+#if ENABLED(SPINDLE_LASER_PWM) && !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11)
+  #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector"
+#endif
 
 #if ENABLED(FAST_PWM_FAN)
   #error "FAST_PWM_FAN is not yet implemented for this platform."

diff --git a/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h b/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h
@@ -21,50 +21,12 @@
  */
 
 /**
- * Test Re-ARM specific configuration values for errors at compile-time.
+ * Test LPC176x-specific configuration values for errors at compile-time.
  */
 
-#if ENABLED(SPINDLE_LASER_ENABLE)
-  #if !PIN_EXISTS(SPINDLE_LASER_ENA)
-    #error "SPINDLE_LASER_ENABLE requires SPINDLE_LASER_ENA_PIN."
-  #elif SPINDLE_DIR_CHANGE && !PIN_EXISTS(SPINDLE_DIR)
-    #error "SPINDLE_DIR_PIN not defined."
-  #elif ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
-    #if !PWM_PIN(SPINDLE_LASER_PWM_PIN)
-      #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin."
-    #elif !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11)
-      #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector"
-    #elif SPINDLE_LASER_POWERUP_DELAY < 1
-      #error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0."
-    #elif SPINDLE_LASER_POWERDOWN_DELAY < 1
-      #error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0."
-    #elif !defined(SPINDLE_LASER_PWM_INVERT)
-      #error "SPINDLE_LASER_PWM_INVERT missing."
-    #elif !defined(SPEED_POWER_SLOPE) || !defined(SPEED_POWER_INTERCEPT) || !defined(SPEED_POWER_MIN) || !defined(SPEED_POWER_MAX)
-      #error "SPINDLE_LASER_PWM equation constant(s) missing."
-    #elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT_PIN."
-    #elif PIN_EXISTS(E0_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E0_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E0_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E1_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E1_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E1_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E2_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E2_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E2_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E3_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E3_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
-    #elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN1_PIN."
-    #elif PIN_EXISTS(FAN2) && SPINDLE_LASER_PWM_PIN == FAN2_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN2_PIN."
-    #elif PIN_EXISTS(CONTROLLERFAN) && SPINDLE_LASER_PWM_PIN == CONTROLLERFAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CONTROLLERFAN_PIN."
-    #endif
-  #endif
-#endif // SPINDLE_LASER_ENABLE
+//#if ENABLED(SPINDLE_LASER_PWM) && !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11)
+//  #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector"
+//#endif
 
 #if IS_RE_ARM_BOARD && ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && HAS_DRIVER(TMC2130) && DISABLED(TMC_USE_SW_SPI)
   #error "Re-ARM with REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER and TMC2130 require TMC_USE_SW_SPI"

diff --git a/Marlin/src/HAL/HAL_STM32/SanityCheck.h b/Marlin/src/HAL/HAL_STM32/SanityCheck.h
@@ -22,49 +22,11 @@
 #pragma once
 
 /**
- * Test Re-ARM specific configuration values for errors at compile-time.
+ * Test STM32-specific configuration values for errors at compile-time.
  */
-#if ENABLED(SPINDLE_LASER_ENABLE)
-  #if !PIN_EXISTS(SPINDLE_LASER_ENA)
-    #error "SPINDLE_LASER_ENABLE requires SPINDLE_LASER_ENA_PIN."
-  #elif SPINDLE_DIR_CHANGE && !PIN_EXISTS(SPINDLE_DIR)
-    #error "SPINDLE_DIR_PIN not defined."
-  #elif ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
-    #if !PWM_PIN(SPINDLE_LASER_PWM_PIN)
-      #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin."
-    #elif !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11)
-      #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector"
-    #elif SPINDLE_LASER_POWERUP_DELAY < 1
-      #error "SPINDLE_LASER_POWERUP_DELAY must be greater than 0."
-    #elif SPINDLE_LASER_POWERDOWN_DELAY < 1
-      #error "SPINDLE_LASER_POWERDOWN_DELAY must be greater than 0."
-    #elif !defined(SPINDLE_LASER_PWM_INVERT)
-      #error "SPINDLE_LASER_PWM_INVERT missing."
-    #elif !defined(SPEED_POWER_SLOPE) || !defined(SPEED_POWER_INTERCEPT) || !defined(SPEED_POWER_MIN) || !defined(SPEED_POWER_MAX)
-      #error "SPINDLE_LASER_PWM equation constant(s) missing."
-    #elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT_PIN."
-    #elif PIN_EXISTS(E0_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E0_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E0_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E1_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E1_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E1_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E2_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E2_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E2_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E3_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E3_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
-    #elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN1_PIN."
-    #elif PIN_EXISTS(FAN2) && SPINDLE_LASER_PWM_PIN == FAN2_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN2_PIN."
-    #elif PIN_EXISTS(CONTROLLERFAN) && SPINDLE_LASER_PWM_PIN == CONTROLLERFAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CONTROLLERFAN_PIN."
-    #endif
-  #endif
-#endif // SPINDLE_LASER_ENABLE
+//#if ENABLED(SPINDLE_LASER_PWM) && !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11)
+//  #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector"
+//#endif
 
 #if ENABLED(EMERGENCY_PARSER)
   #error "EMERGENCY_PARSER is not yet implemented for STM32. Disable EMERGENCY_PARSER to continue."

diff --git a/Marlin/src/HAL/HAL_STM32F1/SanityCheck.h b/Marlin/src/HAL/HAL_STM32F1/SanityCheck.h
@@ -21,52 +21,9 @@
  */
 
 /**
- * HAL for stm32duino.com based on Libmaple and compatible (STM32F1)
+ * Test STM32F1-specific configuration values for errors at compile-time.
  */
 
-/**
- * Test Re-ARM specific configuration values for errors at compile-time.
- */
-#if ENABLED(SPINDLE_LASER_ENABLE)
-  #if !PIN_EXISTS(SPINDLE_LASER_ENA)
-    #error "SPINDLE_LASER_ENABLE requires SPINDLE_LASER_ENA_PIN."
-  #elif SPINDLE_DIR_CHANGE && !PIN_EXISTS(SPINDLE_DIR)
-    #error "SPINDLE_DIR_PIN not defined."
-  #elif ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
-    #if !PWM_PIN(SPINDLE_LASER_PWM_PIN)
-      #error "SPINDLE_LASER_PWM_PIN not assigned to a PWM pin."
-    #elif SPINDLE_LASER_POWERUP_DELAY < 0
-      #error "SPINDLE_LASER_POWERUP_DELAY must be positive"
-    #elif SPINDLE_LASER_POWERDOWN_DELAY < 0
-      #error "SPINDLE_LASER_POWERDOWN_DELAY must be positive"
-    #elif !defined(SPINDLE_LASER_PWM_INVERT)
-      #error "SPINDLE_LASER_PWM_INVERT missing."
-    #elif !defined(SPEED_POWER_SLOPE) || !defined(SPEED_POWER_INTERCEPT) || !defined(SPEED_POWER_MIN) || !defined(SPEED_POWER_MAX)
-      #error "SPINDLE_LASER_PWM equation constant(s) missing."
-    #elif PIN_EXISTS(CASE_LIGHT) && SPINDLE_LASER_PWM_PIN == CASE_LIGHT_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CASE_LIGHT_PIN."
-    #elif PIN_EXISTS(E0_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E0_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E0_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E1_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E1_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E1_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E2_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E2_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E2_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E3_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E3_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E3_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(E4_AUTO_FAN) && SPINDLE_LASER_PWM_PIN == E4_AUTO_FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by E4_AUTO_FAN_PIN."
-    #elif PIN_EXISTS(FAN) && SPINDLE_LASER_PWM_PIN == FAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN_PIN."
-    #elif PIN_EXISTS(FAN1) && SPINDLE_LASER_PWM_PIN == FAN1_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN1_PIN."
-    #elif PIN_EXISTS(FAN2) && SPINDLE_LASER_PWM_PIN == FAN2_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used FAN2_PIN."
-    #elif PIN_EXISTS(CONTROLLERFAN) && SPINDLE_LASER_PWM_PIN == CONTROLLERFAN_PIN
-      #error "SPINDLE_LASER_PWM_PIN is used by CONTROLLERFAN_PIN."
-    #endif
-  #endif
-#endif // SPINDLE_LASER_ENABLE
-
 #if ENABLED(EMERGENCY_PARSER)
   #error "EMERGENCY_PARSER is not yet implemented for STM32F1. Disable EMERGENCY_PARSER to continue."
 #endif