Mellow fly super8

config/mcu_definitions/main/Mellow_Fly_Super8_v1.x.cfg

@@ -0,0 +1,50 @@
+[board_pins mcu_manufacturer]
+aliases:
+    MCU_DRIVE0_STEP=PE2    , MCU_DRIVE0_DIR=PC5    , MCU_DRIVE0_EN=PF11   , MCU_DRIVE0_UART=PC4    ,
+    MCU_DRIVE1_STEP=PE3    , MCU_DRIVE1_DIR=PF13   , MCU_DRIVE1_EN=PF14   , MCU_DRIVE1_UART=PF12   ,
+    MCU_DRIVE2_STEP=PE4    , MCU_DRIVE2_DIR=PG0    , MCU_DRIVE2_EN=PG1    , MCU_DRIVE2_UART=PF15   ,
+    MCU_DRIVE3_STEP=PE14   , MCU_DRIVE3_DIR=PE8    , MCU_DRIVE3_EN=PE9    , MCU_DRIVE3_UART=PE7    ,
+    MCU_DRIVE4_STEP=PE15   , MCU_DRIVE4_DIR=PE11   , MCU_DRIVE4_EN=PF2    , MCU_DRIVE4_UART=PE10   ,
+    MCU_DRIVE5_STEP=PE1    , MCU_DRIVE5_DIR=PF0    , MCU_DRIVE5_EN=PC15   , MCU_DRIVE5_UART=PF1    ,
+    MCU_DRIVE6_STEP=PE0    , MCU_DRIVE6_DIR=PG3    , MCU_DRIVE6_EN=PG4    , MCU_DRIVE6_UART=PG2    ,
+    MCU_DRIVE7_STEP=PE6    , MCU_DRIVE7_DIR=PG6    , MCU_DRIVE7_EN=PG7    , MCU_DRIVE7_UART=PG5    ,
+    MCU_TMC_MOSI=PB5       , MCU_TMC_MISO=PB4      , MCU_TMC_SCK=PB3      ,
+
+    MCU_IO0=PG12  , MCU_IO1=PG11  , MCU_IO2=PG10 , MCU_IO3=PG9  , MCU_IO4=PD7  , MCU_IO5=PD6  , MCU_IO6=PA8  ,
+    MCU_IN7=PF8   ,
+    MCU_HV_IN=PF3 ,
+    MCU_ADC_0=PF4  , MCU_ADC_1=PF5  , MCU_ADC_2=PF9 , MCU_ADC_3=PF10  , MCU_ADC_4=PC0  , MCU_ADC_5=PC1  ,
+
+    MCU_HEAT0=PB0 , MCU_HEAT1=PB1 , MCU_HEAT2=PC7 , MCU_HEAT3=PF7 , MCU_HEAT4=PF6 ,
+
+    MCU_BED=PE5 ,
+
+    # BLTOUCH
+    MCU_SERVO=PC6  , # Pin 3
+    MCU_PROBE=PC3  , # Pin 5
+
+    # ACCELEROMETER
+    MCU_ACCELEROMETER_1=<5V> , MCU_ACCELEROMETER_2=<GND> , MCU_ACCELEROMETER_3=PD0 , MCU_ACCELEROMETER_4=PD1 , MCU_ACCELEROMETER_5=PD3 , MCU_ACCELEROMETER_6=PD4 , MCU_ACCELEROMETER_7=PD5 ,
+
+    # ST-LINK
+    MCU_STLINK_1=<RST> , MCU_STLINK_2=PA14 , MCU_STLINK_3=PA13 , MCU_STLINK_4=<GND> , MCU_STLINK_5=<3.3V> , MCU_STLINK_6=<5V> ,
+
+    # SCREEN
+    MCU_SCREEN_1=PA10 , MCU_SCREEN_2=PA9 , MCU_SCREEN_3=<GND> , MCU_SCREEN_4=<5V> ,
+
+    MCU_FAN0=PA0  , MCU_FAN1=PA1  , MCU_FAN2=PA2  , MCU_FAN3=PA3  , MCU_FAN4=PA15 ,
+    MCU_FAN5=PB11 , MCU_FAN6=PB10 , MCU_FAN7=PD12 , MCU_FAN8=PD14 , MCU_FAN9=PD15 ,
+
+    # EXP1 header
+    EXP1_1=PE12  , EXP1_2=PE13  ,
+    EXP1_3=PB2   , EXP1_4=PG8   ,
+    EXP1_5=PC14  , EXP1_6=PC13  ,  # Slot in the socket on this side
+    EXP1_7=PG14  , EXP1_8=PG13  ,
+    EXP1_9=<GND> , EXP1_10=<5V> ,
+
+    # EXP2 header
+    EXP2_1=PA6   , EXP2_2=PA5   ,
+    EXP2_3=PB7   , EXP2_4=PA4   ,
+    EXP2_5=PB6   , EXP2_6=PA7   ,  # Slot in the socket on this side
+    EXP2_7=PG15  , EXP2_8=<RST> ,
+    EXP2_9=<GND> , EXP2_10=<5V> ,

user_templates/mcu_defaults/main/Mellow_Fly_Super8_v1.x.cfg

@@ -0,0 +1,55 @@
+
+#------------------------------------------#
+#### CUSTOM TEMPLATE MCU definition ########
+#------------------------------------------#
+
+# This template file is a pre-filled file with Klippain pins alias conventions
+# that can be used if your MCU board is not yet officially supported. Just fill
+# in your MCU pins and you will be good to go :)
+
+[mcu]
+##--------------------------------------------------------------------
+serial: /dev/serial/by-id/change-me-to-the-correct-mcu-path
+# canbus_uuid: change-me-to-the-correct-canbus-id
+##--------------------------------------------------------------------
+
+[include config/mcu_definitions/main/Mellow_Fly_Super8_v1.x.cfg] # Do not remove this line
+[board_pins fly_Super8_mcu]
+mcu: mcu
+aliases:
+    X_STEP=MCU_DRIVE0_STEP   , X_DIR=MCU_DRIVE0_DIR   , X_ENABLE=MCU_DRIVE0_EN   , X_TMCUART=MCU_DRIVE0_UART   ,
+    Y_STEP=MCU_DRIVE1_STEP   , Y_DIR=MCU_DRIVE1_DIR   , Y_ENABLE=MCU_DRIVE1_EN   , Y_TMCUART=MCU_DRIVE1_UART   ,
+
+    Z_STEP=MCU_DRIVE3_STEP   , Z_DIR=MCU_DRIVE3_DIR   , Z_ENABLE=MCU_DRIVE3_EN   , Z_TMCUART=MCU_DRIVE3_UART   ,
+    Z1_STEP=MCU_DRIVE4_STEP  , Z1_DIR=MCU_DRIVE4_DIR  , Z1_ENABLE=MCU_DRIVE4_EN  , Z1_TMCUART=MCU_DRIVE4_UART  ,
+    Z2_STEP=MCU_DRIVE5_STEP  , Z2_DIR=MCU_DRIVE5_DIR  , Z2_ENABLE=MCU_DRIVE5_EN  , Z2_TMCUART=MCU_DRIVE5_UART  ,
+    Z3_STEP=MCU_DRIVE6_STEP  , Z3_DIR=MCU_DRIVE6_DIR  , Z3_ENABLE=MCU_DRIVE6_EN  , Z3_TMCUART=MCU_DRIVE6_UART  ,
+
+    E_STEP=MCU_DRIVE2_STEP   , E_DIR=MCU_DRIVE2_DIR   , E_ENABLE=MCU_DRIVE2_EN   , E_TMCUART=MCU_DRIVE2_UART   ,
+
+    DRIVER_SPI_MOSI=MCU_TMC_MOSI , # Used in case of SPI drivers such as TMC2240 or TMC5160
+    DRIVER_SPI_MISO=MCU_TMC_MISO , # Used in case of SPI drivers such as TMC2240 or TMC5160
+    DRIVER_SPI_SCK=MCU_TMC_SCK  , # Used in case of SPI drivers such as TMC2240 or TMC5160
+
+    X_STOP=MCU_IO0 , Y_STOP=MCU_IO1 , Z_STOP=MCU_IO3 ,
+    PROBE_INPUT=MCU_HV_IN  ,
+    RUNOUT_SENSOR=MCU_IO4 ,
+
+    E_HEATER=MCU_HEAT0   , E_TEMPERATURE=MCU_ADC_0   ,
+    BED_HEATER=MCU_BED   , BED_TEMPERATURE=MCU_ADC_5 ,
+
+    PART_FAN=MCU_FAN0 , E_FAN=MCU_FAN1 ,
+    CONTROLLER_FAN=MCU_FAN2        ,
+    EXHAUST_FAN=MCU_FAN3           ,
+    FILTER_FAN=MCU_FAN4            ,
+    HOST_CONTROLLER_FAN=MCU_FAN5   ,
+
+    CHAMBER_TEMPERATURE=MCU_ADC_1 ,
+    ELECTRICAL_CABINET_TEMPERATURE=MCU_ADC_2 ,
+
+    LIGHT_OUTPUT=MCU_HEAT1    ,
+#    LIGHT_NEOPIXEL=  ,
+#    STATUS_NEOPIXEL= ,
+
+    SERVO_PIN=MCU_SERVO ,
+