Skip to content

A Pico W Bluetooth LE MIDI adapter for any class compliant USB MIDI device

License

Notifications You must be signed in to change notification settings

rppicomidi/ble-midi2usbhost

Repository files navigation

ble-midi2usbhost

A Pico W Bluetooth LE MIDI to USB Host adapter for any class compliant USB MIDI device

This project uses the native Raspberry Pi Pico W USB port as a USB MIDI host port and it uses the Bluetooth LE capability of the Pico W's CYW43 WiFi/Bluetooth module to create a Bluetooth LE MIDI GATT Server. You can power the Raspberry Pi Pico W board with any 5V USB C power supply. If you choose to use a 5V phone charger battery pack, make sure that the attached USB MIDI device is bus powered and uses enough power to keep the phone charger battery pack from shutting off automatically.

Because some BLE-MIDI controller apps use a fixed, 0-value timestamp for every message, this code does not attempt to synchronize timestamps to the clock.

This is both a hardware and software project. Please test carefully any hardware you build before you connect your expensive MIDI device to this project. Also be aware that the only current limiting or short circuit protection this project provides for its USB host port comes from the external 5V power source.

If you have problems or need help, please file issues in the Issues tab on the project home page. If you have specific Bluetooth issues and can attach an air trace, that can help a lot. If you find a bug and have a fix for it, pull requests are welcome.

Known Issues

26-Jul-2023:

iPad GarageBand

The iPad GarageBand app Advanced Settings shows the ble-midi2usbhost Pico W Bluetooth successfully connected, but MIDI data does not play GarageBand virtual instruments.

  • Workaround: Use a different iPad BLE-MIDI app like MIDI Wrench or Synth One to connect to the ble-midi2usbhost Pico W Bluetooth first. After that, GarageBand virtual instruments will recognize BLE-MIDI messages.

In my mind, this is an issue with the GarageBand App. GarageBand on my Mac Mini running Monterey works fine. So too do all other BLE-MIDI apps I have tested on my iPad. If this is wrong, please file an issue in this project.

iPad Bluetooth Disconnect Does Not Fully Disconnect

If the Pico W pairs, then disconnects, with an iPad app, you have to fully exit the app and wait a few seconds before you can connect again, or you have to shut off iPad Bluetooth for about a second, then turn it on. It seems the iPad only disconnects from the GATT layer but does not fully disconnect from the Pico W Bluetooth.

By contrast, on my Mac Mini running Monterey, disconnect fully disconnects, so reconnecting is reliable.

Android Bluetooth Reconnection unreliable

If the Pico W Bluetooth pairs, then disconnects, from the Android App TouchDAW, reconnection does not work correctly. Sometimes you have to reboot the phone to get it to connect again. I am not sure if the issue is with ble-midi2usbhost, my cheap phone, TouchDAW, or some combination of these.

Active Sensing is Disabled

If the MIDI keyboard or other device connected via the ble-midi2usbhost USB Host port sends the Active Sensing message, ble-midi2usbhost filters it out. This is done on purpose. In the future, Active Sensing will be supported locally. We don't need to waste Bluetooth bandwidth on this message.

Can't Pair with Linux

Most Linux distributions use the BlueZ Bluetooth stack. By default, BLE-MIDI is disabled. Enabling requires rebuilding the BlueZ stack with the --enable-midi option. You can find old instructions for doing this on the Internet. I have not tried this.

Can't Pair with Windows

I believe BLE-MIDI is not supported in Windows unless the device has its own device driver installed or you are using software like Cubase that supports WinRT MIDI. I have not tried this.

Hardware

The photo shows a Pico W with a microUSB to USB A adapter connected to an Arturia Keylab Essential 88 USB MIDI keyboard. The Pico W is also wired to a USB C breakout board connected to a USB C to USB A cable that is connected to a 5000mAh phone charger battery. The keyboard is bus powered, so the system draws enough power to prevent the phone charger battery from shutting down automatically. An iPad running AudioKit Synth One is connected to the Pico W via BLE-MIDI.

Bill of Materials

I do not get money from hardware vendors. The links to hardware vendors are for illustration and are not endorsements.

  1. A Pico W board see the Raspberry Pi website for more info
  2. A USB C breakout board (e.g. Adafruit 4090)
  3. A microUSB OTG to USA A adapter (e.g. Adafruit 1099)
  4. Wire and solder
  5. 5V USB C power supply (e.g., a battery or AC cell phone charger) and USB C charging cable
  6. 3-pin 0.1" spacing square pin header for connecting the picoprobe debug pins and ground (optional)
  7. 2-pin 0.1" spacing square pin header for connecting the picoprobe ground pins (optional)
  8. A Pico board board programmed as a picoprobe and populated with headers for wiring to the Pico W board (optional)
  9. 5 Jumper wires for connecting the picoprobe to the Pico W (optional)
  10. A microUSB cable to connect the picoprobe to your debug host computer

Wiring

  1. Solder a wire between pin 40 (VBUS pin) of the Pico W and the VBUS pin of the USB C breakout board
  2. Solder a wire between pin 38 (GND pin) of the Pico W and the GND pin of the USB C breakout board
  3. Plug a USB C power cable to the USB C breakout board (but do not activate the 5V power yet).
  4. If you are using a second Pico board programmed picoprobe for debug and serial port
    1. Solder the 2-pin header to pins 1 and 2 of the Pico W board
    2. Solder the 3-pin header to the 3 debug pins of the Pico W board
    3. Attach the microUSB cable to the picoprobe, but do not attach it to the host computer yet.
    4. Use jumper wires to connect the picoprobe to the Pico W board per the instructions in Appendix A of the Getting Started with Raspberry Pi Pico document

Software

The following instructions assume that your Pico SDK code is stored in ${PICO_SDK_PATH} and that your project source tree will be in ${PICO_PROJ}/ble-midi2usbhost. You will likely need to update your version of the TinyUSB library that ships with the Pico SDK. See below.

Getting the project source code

cd ${PICO_PROJ}
git clone https://github.com/rppicomidi/ble-midi2usbhost.git
cd ble-midi2usbhost
git submodule update --recursive --init
mkdir build

When you are done with these steps, your source tree should look like this (library directories, but not files, are shown for brevity).

ble-midi2usbhost/
    |
    +--lib
    |   |
    |   +--pico-w-ble-midi-lib/
    |   |
    |   +--ring-buffer-lib/
    |   |
    |   +--usb_midi_host
    |
    +--ble-midi2usbhost.c
    |
    +--ble-midi2usbhost.gatt
    |
    +--ble-midi2usbhost.jpg
    |
    +--btstack_config.h
    |
    +--CMakeLists.txt
    |
    +--LICENSE
    |
    +--pico_sdk_import.cmake
    |
    +--README.md
    |
    +--tusb_config.h

Installing a tinyusb library that supports the usb_midi_host application library

The Pico SDK uses the main repository for tinyusb as a git submodule. Pico SDK 1.5.1 configured to use version 0.15.0 of TinyUSB. That version does not support application host drivers. You need a version of TinyUSB from 15-Aug-2023 or later. To make sure you have that, follow these instructions

  1. If you have not already done so, follow the instructions for installing the Raspberry Pi Pico SDK in Chapter 2 of the Getting started with Raspberry Pi Pico document. In particular, make sure PICO_SDK_PATH is set to the directory where you installed the pico-sdk and you have installed all of the git submodules.
  2. Set the working directory to the tinyusb library
cd ${PICO_SDK_PATH}/lib/tinyusb
  1. Check out the master branch and pull the latest code.
git checkout master
git pull

Build the Project

Make sure you have defined the following environment variables before either of these steps

export PICO_SDK_PATH=[insert the path to your Pico SDK here]
export PICO_BOARD=pico_w

To build from the command line, type these commands

cd ${PICO_PROJ}/ble-midi2usbhost/build
cmake -DCMAKE_BUILD_TYPE=Debug ..
make

This builds the debug version. If you want the release version, omit -DCMAKE_BUILD_TYPE=Debug. I have done all testing using the debug version.

The build generates the file ${PICO_PROJ}/ble-midi2usbhost/build/ble-midi2usbhost.uf2, which you may then load to the Pico W board by mounting the Pico W as a USB Mass Storage device and dragging the file to it, or you may use the picoprobe to flash code.

Using VisualStudio Code and a picoprobe

This is the workflow I normally use. This project already contains a .vscode directory that should work fine for you.

  1. Set up the environment variables and an instance of openocd as described in the Getting started with Raspberry Pi Pico document.
  2. Start visual studio code in a way that imports the environment variables. From the command line, after you set up the environment, type
code
  1. Click File->Open Folder... and then select the folder where you installed this project.
  2. Choose the tool chain and build as described in Chapter 7 of the Getting started with Raspberry Pi Pico document. Then load the code by running it as described in the same chapter.

Troubleshooting

If your project works for some USB MIDI devices and not others, one thing to check is the size of buffer to hold USB descriptors and other data used for USB enumeration. Look in the file tusb_config.h for

#define CFG_TUH_ENUMERATION_BUFSIZE 512

Very complex MIDI devices or USB Audio+MIDI devices like DSP guitar pedals or MIDI workstation keyboards may have large USB configuration descriptors. This project assumes 512 bytes is enough, but it may not be for your device.

To check if the descriptor size is the issue, use your development computer to dump the USB descriptor for your device and then add up the wTotalLength field values for each configuration in the descriptor.

For Linux and MacOS Homebrew, the command is lsusb -d [vid]:[pid] -v For Windows, it is simplest to install a program like Thesycon USB Descriptor Dumper.

For example, this is the important information from lsusb -d 0944:0117 -v from a Korg nanoKONTROL2:

  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x0053
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              100mA

This is the important information from the Thesycon USB Descriptor Dumper for a Valeton NUX MG-400

0x01	bNumConfigurations

Device Qualifier Descriptor is not available. Error code: 0x0000001F


-------------------------
Configuration Descriptor:
-------------------------
0x09	bLength
0x02	bDescriptorType
0x0158	wTotalLength   (344 bytes)
0x04	bNumInterfaces
0x01	bConfigurationValue
0x00	iConfiguration
0xC0	bmAttributes   (Self-powered Device)
0x00	bMaxPower      (0 mA)

You can see that if CFG_TUH_ENUMERATION_BUFSIZE were 256 instead of 512, the Korg nanoKONTROL2 would have no trouble enumerating but the Valeton NUX MG-400 would fail because TinyUSB couldn't load the whole configuration descriptor to memory.

Tweaking the Pairing Model

This project as written uses "Just Works" pairing with bonding for maximum ease of use. If you want to add more authentication features, I put the hooks in the SM callback handler, but you will need to add more hardware for a display (IO_CAPABILITY_DISPLAY_ONLY), a display and yes/no buttons (IO_CAPABILITY_DISPLAY_YES_NO), or a keyboard (IO_CAPABILITY_KEYBOARD_ONLY). If you want to add IO_CAPABILITY_KEYBOARD_ONLY I/O capability without dedicating a keyboard to the device, you could add USB HID keyboard support to the USB Host configuration and modify the software to handle HID reports. You would plug a USB HID keyboard to the USB Host port of the ble-midi2usbhost hardware during pairing. Then you would unplug the HID keyboard and plug in your MIDI device during normal operation.

If you want to disable legacy pairing in the name of more security, add the line

sm_set_secure_connections_only_mode(true);

before any other sm_ function calls.

If you want to use a packet sniffer to get an air trace of the BLE-MIDI stream, it is simpler if you use legacy pairing. To do that, in ble-midi2usbhost.c, change the line

sm_set_authentication_requirements(SM_AUTHREQ_SECURE_CONNECTION | SM_AUTHREQ_BONDING);

to

sm_set_authentication_requirements(SM_AUTHREQ_BONDING);

.

Releases

No releases published

Packages

No packages published