A fork from erikrrodriguez's metro-sign (based on metro-sign) which adds button functionality.

Adds:

• Button support to hide the top banner and allow 4 trains to show
• Button support to switch between alternating groups, showing two groups, or one at a time
• New fonts

Based on:

• Forked from erikrrodriguez, who included:
  • Walking distance modifier
  • Updated to CircutPython 8
  • Incorporated scottiecarcia's off-hours and Metrohero API
  • Incorporated ScottKekoaShay's auto-swapping of stations
• Also used GJT-34's awesome Metroesque.bdf font

Washington DC Metro Train Sign

This project contains the source code to create your own Washington DC Metro sign. It was written using CircuitPython targeting the Adafruit Matrix Portal and is optimized for 64x32 RGB LED matrices.

How To

Hardware

• An Adafruit Matrix Portal - $24.99
• A 64x32 RGB LED matrix compatible with the Matrix Portal - $39.99 to $84.99
  • 64x32 RGB LED Matrix - 3mm pitch
  • 64x32 RGB LED Matrix - 4mm pitch
  • 64x32 RGB LED Matrix - 5mm pitch
  • 64x32 RGB LED Matrix - 6mm pitch
• A USB-C power supply (15w phone adapters should work fine for this code, but the panels can theoretically pull 20w if every pixel is on white)
• A USB-C cable that can connect your computer/power supply to the board
• LED diffuser film (optional)

Tools

• A small phillips head screwdriver
• A hot glue gun (optional)
• Tape (optional)

Part 1: Prepare the Board

1. Use a hot glue gun to cover the sharp screws on the right-hand side of the 64x32 LED matrix. This step is optional, but it will prevent wire chafing later on.

   

2. Lightly screw in the phillips head screws into the posts on the Matrix Portal. These only need to go down about 60% of the way.

   

3. Using the power cable provided with 64x32 matrix, slide the prong for the red power cable between the post and the screw on the port labeled 5v. Tighten down this screw all the way using your screwdriver. Repeat the same for the black power cable and the GND port.

   

4. Connect the Matrix Portal to the large connector on the left-hand side of the back of the 64x32 matrix.

   

5. Plug one of the power connectors into the right-hand side of the 64x32 matrix.

   

6. You can use masking tape (or painter's tape) to prevent the cables from flopping around.

   

Part 2: Loading the Software

1. Connect the board to your computer using a USB C cable. Double click the button on the board labeled RESET. The board should mount onto your computer as a storage volume, most likely named MATRIXBOOT.

   

2. Flash your Matrix Portal with the latest release of CircuitPython 8.

   • Download the firmware from Adafruit.
   • Drag the downloaded .uf2 file into the root of the MATRIXBOOT volume.
   • The board will automatically flash the version of CircuitPython and remount as CIRCUITPY.
   • If something goes wrong, refer to the Adafruit Documentation.

3. Decompress the lib.zip file for 8.x from this repository into the root of the CIRCUITPY volume. There should be one folder named lib, with a plethora of files underneath. You can delete lib.zip from the CIRCUITPY volume, as it's no longer needed.

   • It has been reported that this step may fail (Issue #2), most likely due to the storage on the Matrix Portal not being able to handle the decompression. If this happens, unzip the lib.zip file on your computer, and copy the lib folder to the Matrix Portal. Command line tools could also be used if the above doesn't work.

   

4. Copy all of the Python files from src in this repository into the root of the CIRCUITPY volume. Also copy the two *.bdf files into the the lib

   

5. The board should now light up with a loading screen, but we've still got some work to do. The picture below shows the board without LED diffuser film.

   

Part 3: Getting a WMATA / Metro Hero API Key

Two API's are available with public metro data. The Official WMATA API and the MetroHero API. Either will work, but I opt for the latter because I think it's train times are more accurate and because it gives estimates for trains >30 minutes away. Either will work correctly, at least until Metrohero sunsets in July 2023, RIP.

Part 3.a: Getting a WMATA API Key

1. Create a WMATA developer account on WMATA's Developer Website.
2. After your account is created, add the Default Tier subscription to your account on this page.
3. After doing this, you will be redirected to your profile.
4. Under the Subscriptions section on your profile, select the show button beside the Primary Key. This is the key that allows the board to communicate with WMATA.

Part 3.b: Getting a Metro Hero Key

1. Send an polite email to contact@dcmetrohero.com asking for an API Key. MetroHero's Developer Website.
2. Wait patiently for their reply with your API key.

Part 4: (Optional) Obtain adafruit IO Key for Off Hours.

If you'd like to configure your board to turn the display off for certain hours of the day, you'll need to set up a free account with Adafruit to make requests for the local time. You may skip this if you are not interested in this feature.

1. Follow steps 1-3 outlined here.
2. Make note of your username and your Adafruit IO key.

Part 5: Configuring the Board

1. Open the secrets.py file located in the root of the CIRCUITPY volume.
   1. Fill in your WiFi ssid and password.
   2. Set either the wmata_api_key or metro_hero_api_key to the API key you got from Part 3.
2. Open the config.py file located in the root of the CIRCUITPY volumse.
   1. If using MetroHero, update the source_api field to MetroHero.
   2. Select your stations and lines from the Metro Station Codes table, and set the metro_station_codes value to the corresponding value in the table.
   3. For train_groups_1, the values need to be either '1' or '2' or '3'. This determines which platform's arrival times will be displayed. These typically fall in line with the values provided in the Train Group table, although single tracking and other events can cause these to change. The ordering must match the ordering used in metro_station_codes.
   4. Set the walking_times values to the time it takes you to get to these stations. This will make your sign ignore trains arriving in less than this much time.
3. (Optional) Under the Off Hours Configuration section:
   1. Set aio_username to the username you created with Adafruit in Part 4.
   2. Set aio_key to the api key associated with your Adafruit account.
   3. Set the display_on_time and display_off_time variables to the time of day you would like the sign to be turned off and on. Note that they must be of the format "HH:MM" and use a 24 hour clock.
4. After you save these files, your board should refresh and connect to WMATA.

Part 6: Using the Board

Powering on

1. The board will automatically run the metro code on every power-up, by plugging in any USB-C cable.

Using the buttons

1. You can change between showing three of four lines of trains (with and without the heading text) by pressing the 'UP' button on the board. This is shown below

2. You can also change which train groups to show by pressing the 'DOWN' button the board. The modes will cycle as follows:

Mode	Shows
Both groups	Both train groups at once (merged, sorted by earliest)
Alt. groups	Alternate between groups every few seconds
Group 1	Shows only the first group set in config.py
Group 2	Shows only the second group set in config.py

After you press the DOWN button, wait for the text to show to confirm the change

Troubleshooting

If something goes wrong, take a peek at the Adafruit Documentation. Additionally, you can connect to the board using a serial connection to gain access to its logging.

Appendix

DC Metro Station Codes

Name	Lines	Code
Addison Road-Seat Pleasant	BL, SV	G03
Anacostia	GR	F06
Archives-Navy Memorial-Penn Quarter	GR, YL	F02
Arlington Cemetery	BL	C06
Ballston-MU	OR, SV	K04
Benning Road	BL, SV	G01
Bethesda	RD	A09
Braddock Road	BL, YL	C12
Branch Ave	GR	F11
Brookland-CUA	RD	B05
Capitol Heights	BL, SV	G02
Capitol South	BL, OR, SV	D05
Cheverly	OR	D11
Clarendon	OR, SV	K02
Cleveland Park	RD	A05
College Park-U of Md	GR	E09
Columbia Heights	GR, YL	E04
Congress Heights	GR	F07
Court House	OR, SV	K01
Crystal City	BL, YL	C09
Deanwood	OR	D10
Dunn Loring-Merrifield	OR	K07
Dupont Circle	RD	A03
East Falls Church	OR, SV	K05
Eastern Market	BL, OR, SV	D06
Eisenhower Avenue	YL	C14
Farragut North	RD	A02
Farragut West	BL, OR, SV	C03
Federal Center SW	BL, OR, SV	D04
Federal Triangle	BL, OR, SV	D01
Foggy Bottom-GWU	BL, OR, SV	C04
Forest Glen	RD	B09
Fort Totten	RD	B06
Fort Totten	GR, YL	E06
Franconia-Springfield	BL	J03
Friendship Heights	RD	A08
Gallery Pl-Chinatown	RD	B01
Gallery Pl-Chinatown	GR, YL	F01
Georgia Ave-Petworth	GR, YL	E05
Glenmont	RD	B11
Greenbelt	GR	E10
Greensboro	SV	N03
Grosvenor-Strathmore	RD	A11
Huntington	YL	C15
Judiciary Square	RD	B02
King St-Old Town	BL, YL	C13
L'Enfant Plaza	BL, OR, SV	D03
L'Enfant Plaza	GR, YL	F03
Landover	OR	D12
Largo Town Center	BL, SV	G05
McLean	SV	N01
McPherson Square	BL, OR, SV	C02
Medical Center	RD	A10
Metro Center	RD	A01
Metro Center	BL, OR, SV	C01
Minnesota Ave	OR	D09
Morgan Boulevard	BL, SV	G04
Mt Vernon Sq 7th St-Convention Center	GR, YL	E01
Navy Yard-Ballpark	GR	F05
Naylor Road	GR	F09
New Carrollton	OR	D13
NoMa-Gallaudet U	RD	B35
Pentagon	BL, YL	C07
Pentagon City	BL, YL	C08
Potomac Ave	BL, OR, SV	D07
Prince George's Plaza	GR	E08
Rhode Island Ave-Brentwood	RD	B04
Rockville	RD	A14
Ronald Reagan Washington National Airport	BL, YL	C10
Rosslyn	BL, OR, SV	C05
Shady Grove	RD	A15
Shaw-Howard U	GR, YL	E02
Silver Spring	RD	B08
Smithsonian	BL, OR, SV	D02
Southern Avenue	GR	F08
Spring Hill	SV	N04
Stadium-Armory	BL, OR, SV	D08
Suitland	GR	F10
Takoma	RD	B07
Tenleytown-AU	RD	A07
Twinbrook	RD	A13
Tysons Corner	SV	N02
U Street/African-Amer Civil War Memorial/Cardozo	GR, YL	E03
Union Station	RD	B03
Van Dorn Street	BL	J02
Van Ness-UDC	RD	A06
Vienna/Fairfax-GMU	OR	K08
Virginia Square-GMU	OR, SV	K03
Waterfront	GR	F04
West Falls Church-VT/UVA	OR	K06
West Hyattsville	GR	E07
Wheaton	RD	B10
White Flint	RD	A12
Wiehle-Reston East	SV	N06
Woodley Park-Zoo/Adams Morgan	RD	A04

DC Metro Silver Line Phase II Stations

A special thanks to u/SandBoxJohn for these.

Name	Lines	Code
Reston Town Center	SV	N07
Herndon	SV	N08
Innovation Center	SV	N09
Dulles Airport	SV	N10
Loudoun Gateway	SV	N11
Ashburn	SV	N12

Train Group Explanations

A special thanks to u/SandBoxJohn for these.

Line	Train Group	Destination
RD	"1"	Glenmont
RD	"2"	Shady Grove
BL, OR, SV	"1"	New Carrollton, Largo Town Center
BL, OR, SV	"2"	Vienna, Franconia-Springfield, Wiehle-Reston East
GR, YL	"1"	Greenbelt
GR, YL	"2"	Huntington, Branch Avenue
N/A	"3"	Center Platform at National Airport, West Falls Church