forked from skristiansson/linux
-
Notifications
You must be signed in to change notification settings - Fork 14
/
Copy pathKconfig
2569 lines (2105 loc) · 78 KB
/
Kconfig
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
# SPDX-License-Identifier: GPL-2.0-only
#
# Hardware monitoring chip drivers configuration
#
menuconfig HWMON
tristate "Hardware Monitoring support"
depends on HAS_IOMEM
default y
help
Hardware monitoring devices let you monitor the hardware health
of a system. Most modern motherboards include such a device. It
can include temperature sensors, voltage sensors, fan speed
sensors and various additional features such as the ability to
control the speed of the fans. If you want this support you
should say Y here and also to the specific driver(s) for your
sensors chip(s) below.
To find out which specific driver(s) you need, use the
sensors-detect script from the lm_sensors package. Read
<file:Documentation/hwmon/userspace-tools.rst> for details.
This support can also be built as a module. If so, the module
will be called hwmon.
if HWMON
config HWMON_VID
tristate
config HWMON_DEBUG_CHIP
bool "Hardware Monitoring Chip debugging messages"
help
Say Y here if you want the I2C chip drivers to produce a bunch of
debug messages to the system log. Select this if you are having
a problem with I2C support and want to see more of what is going
on.
comment "Native drivers"
config SENSORS_ABITUGURU
tristate "Abit uGuru (rev 1 & 2)"
depends on (X86 && DMI) || COMPILE_TEST && HAS_IOPORT
help
If you say yes here you get support for the sensor part of the first
and second revision of the Abit uGuru chip. The voltage and frequency
control parts of the Abit uGuru are not supported. The Abit uGuru
chip can be found on Abit uGuru featuring motherboards (most modern
Abit motherboards from before end 2005). For more info and a list
of which motherboards have which revision see
Documentation/hwmon/abituguru.rst
This driver can also be built as a module. If so, the module
will be called abituguru.
config SENSORS_ABITUGURU3
tristate "Abit uGuru (rev 3)"
depends on (X86 && DMI) || COMPILE_TEST && HAS_IOPORT
help
If you say yes here you get support for the sensor part of the
third revision of the Abit uGuru chip. Only reading the sensors
and their settings is supported. The third revision of the Abit
uGuru chip can be found on recent Abit motherboards (since end
2005). For more info and a list of which motherboards have which
revision see Documentation/hwmon/abituguru3.rst
This driver can also be built as a module. If so, the module
will be called abituguru3.
config SENSORS_SMPRO
tristate "Ampere's Altra SMpro hardware monitoring driver"
depends on MFD_SMPRO
help
If you say yes here you get support for the thermal, voltage,
current and power sensors of Ampere's Altra processor family SoC
with SMpro co-processor.
config SENSORS_AD7314
tristate "Analog Devices AD7314 and compatibles"
depends on SPI
help
If you say yes here you get support for the Analog Devices
AD7314, ADT7301 and ADT7302 temperature sensors.
This driver can also be built as a module. If so, the module
will be called ad7314.
config SENSORS_AD7414
tristate "Analog Devices AD7414"
depends on I2C
help
If you say yes here you get support for the Analog Devices
AD7414 temperature monitoring chip.
This driver can also be built as a module. If so, the module
will be called ad7414.
config SENSORS_AD7418
tristate "Analog Devices AD7416, AD7417 and AD7418"
depends on I2C
help
If you say yes here you get support for the Analog Devices
AD7416, AD7417 and AD7418 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called ad7418.
config SENSORS_ADM1021
tristate "Analog Devices ADM1021 and compatibles"
depends on I2C
depends on SENSORS_LM90=n
help
If you say yes here you get support for Analog Devices ADM1021
and ADM1023 sensor chips and clones: Maxim MAX1617 and MAX1617A,
Genesys Logic GL523SM, National Semiconductor LM84 and TI THMC10.
This driver can also be built as a module. If so, the module
will be called adm1021.
config SENSORS_ADM1025
tristate "Analog Devices ADM1025 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1025
and Philips NE1619 sensor chips.
This driver can also be built as a module. If so, the module
will be called adm1025.
config SENSORS_ADM1026
tristate "Analog Devices ADM1026 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM1026
sensor chip.
This driver can also be built as a module. If so, the module
will be called adm1026.
config SENSORS_ADM1029
tristate "Analog Devices ADM1029"
depends on I2C
help
If you say yes here you get support for Analog Devices ADM1029
sensor chip.
Very rare chip, please let us know you use it.
This driver can also be built as a module. If so, the module
will be called adm1029.
config SENSORS_ADM1031
tristate "Analog Devices ADM1031 and compatibles"
depends on I2C
help
If you say yes here you get support for Analog Devices ADM1031
and ADM1030 sensor chips.
This driver can also be built as a module. If so, the module
will be called adm1031.
config SENSORS_ADM1177
tristate "Analog Devices ADM1177 and compatibles"
depends on I2C
help
If you say yes here you get support for Analog Devices ADM1177
sensor chips.
This driver can also be built as a module. If so, the module
will be called adm1177.
config SENSORS_ADM9240
tristate "Analog Devices ADM9240 and compatibles"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Analog Devices ADM9240,
Dallas DS1780, National Semiconductor LM81 sensor chips.
This driver can also be built as a module. If so, the module
will be called adm9240.
config SENSORS_ADT7X10
tristate
select REGMAP
help
This module contains common code shared by the ADT7310/ADT7320 and
ADT7410/ADT7420 temperature monitoring chip drivers.
If built as a module, the module will be called adt7x10.
config SENSORS_ADT7310
tristate "Analog Devices ADT7310/ADT7320"
depends on SPI_MASTER
select SENSORS_ADT7X10
help
If you say yes here you get support for the Analog Devices
ADT7310 and ADT7320 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7310.
config SENSORS_ADT7410
tristate "Analog Devices ADT7410/ADT7420"
depends on I2C
select SENSORS_ADT7X10
help
If you say yes here you get support for the Analog Devices
ADT7410 and ADT7420 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7410.
config SENSORS_ADT7411
tristate "Analog Devices ADT7411"
depends on I2C
help
If you say yes here you get support for the Analog Devices
ADT7411 voltage and temperature monitoring chip.
This driver can also be built as a module. If so, the module
will be called adt7411.
config SENSORS_ADT7462
tristate "Analog Devices ADT7462"
depends on I2C
help
If you say yes here you get support for the Analog Devices
ADT7462 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7462.
config SENSORS_ADT7470
tristate "Analog Devices ADT7470"
depends on I2C
help
If you say yes here you get support for the Analog Devices
ADT7470 temperature monitoring chips.
This driver can also be built as a module. If so, the module
will be called adt7470.
config SENSORS_ADT7475
tristate "Analog Devices ADT7473, ADT7475, ADT7476 and ADT7490"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Analog Devices
ADT7473, ADT7475, ADT7476 and ADT7490 hardware monitoring
chips.
This driver can also be built as a module. If so, the module
will be called adt7475.
config SENSORS_AHT10
tristate "Aosong AHT10, AHT20"
depends on I2C
select CRC8
help
If you say yes here, you get support for the Aosong AHT10 and AHT20
temperature and humidity sensors
This driver can also be built as a module. If so, the module
will be called aht10.
config SENSORS_AQUACOMPUTER_D5NEXT
tristate "Aquacomputer D5 Next, Octo, Quadro, Farbwerk, Farbwerk 360, High Flow Next"
depends on USB_HID
select CRC16
help
If you say yes here you get support for sensors and fans of
the Aquacomputer D5 Next watercooling pump, Octo and Quadro fan
controllers, Farbwerk and Farbwerk 360 RGB controllers, High Flow
Next sensor, where available.
This driver can also be built as a module. If so, the module
will be called aquacomputer_d5next.
config SENSORS_AS370
tristate "Synaptics AS370 SoC hardware monitoring driver"
help
If you say yes here you get support for the PVT sensors of
the Synaptics AS370 SoC
This driver can also be built as a module. If so, the module
will be called as370-hwmon.
config SENSORS_ASC7621
tristate "Andigilog aSC7621"
depends on I2C
help
If you say yes here you get support for the aSC7621
family of SMBus sensors chip found on most Intel X38, X48, X58,
945, 965 and 975 desktop boards. Currently supported chips:
aSC7621
aSC7621a
This driver can also be built as a module. If so, the module
will be called asc7621.
config SENSORS_ASUS_ROG_RYUJIN
tristate "ASUS ROG RYUJIN II 360 hardware monitoring driver"
depends on HID
help
If you say yes here you get support for the fans and sensors of
the ASUS ROG RYUJIN II 360 AIO CPU liquid cooler.
This driver can also be built as a module. If so, the module
will be called asus_rog_ryujin.
config SENSORS_AXI_FAN_CONTROL
tristate "Analog Devices FAN Control HDL Core driver"
help
If you say yes here you get support for the Analog Devices
AXI HDL FAN monitoring core.
This driver can also be built as a module. If so, the module
will be called axi-fan-control
config SENSORS_K8TEMP
tristate "AMD Athlon64/FX or Opteron temperature sensor"
depends on X86 && PCI
help
If you say yes here you get support for the temperature
sensor(s) inside your CPU. Supported is whole AMD K8
microarchitecture. Please note that you will need at least
lm-sensors 2.10.1 for proper userspace support.
This driver can also be built as a module. If so, the module
will be called k8temp.
config SENSORS_K10TEMP
tristate "AMD Family 10h+ temperature sensor"
depends on X86 && PCI && AMD_NB
help
If you say yes here you get support for the temperature
sensor(s) inside your CPU. Supported are later revisions of
the AMD Family 10h and all revisions of the AMD Family 11h,
12h (Llano), 14h (Brazos), 15h (Bulldozer/Trinity/Kaveri/Carrizo)
and 16h (Kabini/Mullins) microarchitectures.
This driver can also be built as a module. If so, the module
will be called k10temp.
config SENSORS_FAM15H_POWER
tristate "AMD Family 15h processor power"
depends on X86 && PCI && CPU_SUP_AMD
help
If you say yes here you get support for processor power
information of your AMD family 15h CPU.
This driver can also be built as a module. If so, the module
will be called fam15h_power.
config SENSORS_APPLESMC
tristate "Apple SMC (Motion sensor, light sensor, keyboard backlight)"
depends on INPUT && X86
select NEW_LEDS
select LEDS_CLASS
help
This driver provides support for the Apple System Management
Controller, which provides an accelerometer (Apple Sudden Motion
Sensor), light sensors, temperature sensors, keyboard backlight
control and fan control.
Only Intel-based Apple's computers are supported (MacBook Pro,
MacBook, MacMini).
Data from the different sensors, keyboard backlight control and fan
control are accessible via sysfs.
This driver also provides an absolute input class device, allowing
the laptop to act as a pinball machine-esque joystick.
Say Y here if you have an applicable laptop and want to experience
the awesome power of applesmc.
config SENSORS_ARM_SCMI
tristate "ARM SCMI Sensors"
depends on ARM_SCMI_PROTOCOL
depends on THERMAL || !THERMAL_OF
help
This driver provides support for temperature, voltage, current
and power sensors available on SCMI based platforms. The actual
number and type of sensors exported depend on the platform.
This driver can also be built as a module. If so, the module
will be called scmi-hwmon.
config SENSORS_ARM_SCPI
tristate "ARM SCPI Sensors"
depends on ARM_SCPI_PROTOCOL
depends on THERMAL || !THERMAL_OF
help
This driver provides support for temperature, voltage, current
and power sensors available on ARM Ltd's SCP based platforms. The
actual number and type of sensors exported depend on the platform.
config SENSORS_ASB100
tristate "Asus ASB100 Bach"
depends on (X86 || COMPILE_TEST) && I2C
select HWMON_VID
help
If you say yes here you get support for the ASB100 Bach sensor
chip found on some Asus mainboards.
This driver can also be built as a module. If so, the module
will be called asb100.
config SENSORS_ASPEED
tristate "ASPEED AST2400/AST2500 PWM and Fan tach driver"
depends on ARCH_ASPEED || COMPILE_TEST
depends on THERMAL || THERMAL=n
select REGMAP
help
This driver provides support for ASPEED AST2400/AST2500 PWM
and Fan Tacho controllers.
This driver can also be built as a module. If so, the module
will be called aspeed_pwm_tacho.
config SENSORS_ASPEED_G6
tristate "ASPEED g6 PWM and Fan tach driver"
depends on ARCH_ASPEED || COMPILE_TEST
depends on PWM
help
This driver provides support for ASPEED G6 PWM and Fan Tach
controllers.
This driver can also be built as a module. If so, the module
will be called aspeed_pwm_tacho.
config SENSORS_ATXP1
tristate "Attansic ATXP1 VID controller"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for the Attansic ATXP1 VID
controller.
If your board have such a chip, you are able to control your CPU
core and other voltages.
This driver can also be built as a module. If so, the module
will be called atxp1.
config SENSORS_BT1_PVT
tristate "Baikal-T1 Process, Voltage, Temperature sensor driver"
depends on MIPS_BAIKAL_T1 || COMPILE_TEST
select POLYNOMIAL
help
If you say yes here you get support for Baikal-T1 PVT sensor
embedded into the SoC.
This driver can also be built as a module. If so, the module will be
called bt1-pvt.
config SENSORS_BT1_PVT_ALARMS
bool "Enable Baikal-T1 PVT sensor alarms"
depends on SENSORS_BT1_PVT
help
Baikal-T1 PVT IP-block provides threshold registers for each
supported sensor. But the corresponding interrupts might be
generated by the thresholds comparator only in synchronization with
a data conversion. Additionally there is only one sensor data can
be converted at a time. All of these makes the interface impossible
to be used for the hwmon alarms implementation without periodic
switch between the PVT sensors. By default the data conversion is
performed on demand from the user-space. If this config is enabled
the data conversion will be periodically performed and the data will be
saved in the internal driver cache.
config SENSORS_CHIPCAP2
tristate "Amphenol ChipCap 2 relative humidity and temperature sensor"
depends on I2C
help
Say yes here to build support for the Amphenol ChipCap 2
relative humidity and temperature sensor.
To compile this driver as a module, choose M here: the module
will be called chipcap2.
config SENSORS_CORSAIR_CPRO
tristate "Corsair Commander Pro controller"
depends on HID
help
If you say yes here you get support for the Corsair Commander Pro
controller.
This driver can also be built as a module. If so, the module
will be called corsair-cpro.
config SENSORS_CORSAIR_PSU
tristate "Corsair PSU HID controller"
depends on HID
help
If you say yes here you get support for Corsair PSUs with a HID
interface.
Currently this driver supports the (RM/HX)550i, (RM/HX)650i,
(RM/HX)750i, (RM/HX)850i, (RM/HX)1000i and HX1200i power supplies
by Corsair.
This driver can also be built as a module. If so, the module
will be called corsair-psu.
config SENSORS_DRIVETEMP
tristate "Hard disk drives with temperature sensors"
depends on SCSI && ATA
help
If you say yes you get support for the temperature sensor on
hard disk drives.
This driver can also be built as a module. If so, the module
will be called drivetemp.
config SENSORS_DS620
tristate "Dallas Semiconductor DS620"
depends on I2C
help
If you say yes here you get support for Dallas Semiconductor
DS620 sensor chip.
This driver can also be built as a module. If so, the module
will be called ds620.
config SENSORS_DS1621
tristate "Dallas Semiconductor DS1621 and compatibles"
depends on I2C
help
If you say yes here you get support for Dallas Semiconductor/Maxim
Integrated DS1621 sensor chips and compatible models including:
- Dallas Semiconductor DS1625
- Maxim Integrated DS1631
- Maxim Integrated DS1721
- Maxim Integrated DS1731
This driver can also be built as a module. If so, the module
will be called ds1621.
config SENSORS_DELL_SMM
tristate "Dell laptop SMM BIOS hwmon driver"
depends on ACPI_WMI
depends on X86
imply THERMAL
help
This hwmon driver adds support for reporting temperature of different
sensors and controls the fans on Dell laptops via System Management
Mode provided by Dell BIOS.
When option I8K is also enabled this driver provides legacy /proc/i8k
userspace interface for i8kutils package.
config I8K
bool "Legacy /proc/i8k interface of Dell laptop SMM BIOS hwmon driver"
depends on SENSORS_DELL_SMM
depends on PROC_FS
help
This option enables the legacy /proc/i8k userspace interface of the
dell-smm-hwmon driver. The character file /proc/i8k exposes the BIOS
version, temperatures and allows control of fan speeds of some Dell
laptops. Sometimes it also reports power and hotkey status.
This interface is required to run programs from the i8kutils package.
Say Y if you intend to run userspace programs that use this interface.
Say N otherwise.
config SENSORS_DA9052_ADC
tristate "Dialog DA9052/DA9053 ADC"
depends on PMIC_DA9052
help
Say y here to support the ADC found on Dialog Semiconductor
DA9052-BC and DA9053-AA/Bx PMICs.
This driver can also be built as module. If so, the module
will be called da9052-hwmon.
config SENSORS_DA9055
tristate "Dialog Semiconductor DA9055 ADC"
depends on MFD_DA9055
help
If you say yes here you get support for ADC on the Dialog
Semiconductor DA9055 PMIC.
This driver can also be built as a module. If so, the module
will be called da9055-hwmon.
config SENSORS_I5K_AMB
tristate "FB-DIMM AMB temperature sensor on Intel 5000 series chipsets"
depends on PCI
help
If you say yes here you get support for FB-DIMM AMB temperature
monitoring chips on systems with the Intel 5000 series chipset.
This driver can also be built as a module. If so, the module
will be called i5k_amb.
config SENSORS_SPARX5
tristate "Sparx5 SoC temperature sensor"
depends on ARCH_SPARX5 || COMPILE_TEST
help
If you say yes here you get support for temperature monitoring
with the Microchip Sparx5 SoC.
This driver can also be built as a module. If so, the module
will be called sparx5-temp.
config SENSORS_F71805F
tristate "Fintek F71805F/FG, F71806F/FG and F71872F/FG"
depends on HAS_IOPORT
depends on !PPC
help
If you say yes here you get support for hardware monitoring
features of the Fintek F71805F/FG, F71806F/FG and F71872F/FG
Super-I/O chips.
This driver can also be built as a module. If so, the module
will be called f71805f.
config SENSORS_F71882FG
tristate "Fintek F71882FG and compatibles"
depends on HAS_IOPORT
depends on !PPC
help
If you say yes here you get support for hardware monitoring
features of many Fintek Super-I/O (LPC) chips. The currently
supported chips are:
F71808E/A
F71858FG
F71862FG
F71863FG
F71869F/E/A
F71882FG
F71883FG
F71889FG/ED/A
F8000
F81801U
F81865F
This driver can also be built as a module. If so, the module
will be called f71882fg.
config SENSORS_F75375S
tristate "Fintek F75375S/SP, F75373 and F75387"
depends on I2C
help
If you say yes here you get support for hardware monitoring
features of the Fintek F75375S/SP, F75373 and F75387
This driver can also be built as a module. If so, the module
will be called f75375s.
config SENSORS_GSC
tristate "Gateworks System Controller ADC"
depends on MFD_GATEWORKS_GSC
help
Support for the Gateworks System Controller A/D converters.
To compile this driver as a module, choose M here:
the module will be called gsc-hwmon.
config SENSORS_MC13783_ADC
tristate "Freescale MC13783/MC13892 ADC"
depends on MFD_MC13XXX
help
Support for the A/D converter on MC13783 and MC13892 PMIC.
config SENSORS_FSCHMD
tristate "Fujitsu Siemens Computers sensor chips"
depends on (X86 || COMPILE_TEST) && I2C
help
If you say yes here you get support for the following Fujitsu
Siemens Computers (FSC) sensor chips: Poseidon, Scylla, Hermes,
Heimdall, Heracles, Hades and Syleus including support for the
integrated watchdog.
This is a merged driver for FSC sensor chips replacing the fscpos,
fscscy and fscher drivers and adding support for several other FSC
sensor chips.
This driver can also be built as a module. If so, the module
will be called fschmd.
config SENSORS_FTSTEUTATES
tristate "Fujitsu Technology Solutions sensor chip Teutates"
depends on I2C && WATCHDOG
select WATCHDOG_CORE
help
If you say yes here you get support for the Fujitsu Technology
Solutions (FTS) sensor chip "Teutates" including support for
the integrated watchdog.
This driver can also be built as a module. If so, the module
will be called ftsteutates.
config SENSORS_GIGABYTE_WATERFORCE
tristate "Gigabyte Waterforce X240/X280/X360 AIO CPU coolers"
depends on USB_HID
help
If you say yes here you get support for hardware monitoring for the
Gigabyte Waterforce X240/X280/X360 all-in-one CPU liquid coolers.
This driver can also be built as a module. If so, the module
will be called gigabyte_waterforce.
config SENSORS_GL518SM
tristate "Genesys Logic GL518SM"
depends on I2C
help
If you say yes here you get support for Genesys Logic GL518SM
sensor chips.
This driver can also be built as a module. If so, the module
will be called gl518sm.
config SENSORS_GL520SM
tristate "Genesys Logic GL520SM"
depends on I2C
select HWMON_VID
help
If you say yes here you get support for Genesys Logic GL520SM
sensor chips.
This driver can also be built as a module. If so, the module
will be called gl520sm.
config SENSORS_G760A
tristate "GMT G760A"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G760A fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g760a.
config SENSORS_G762
tristate "GMT G762 and G763"
depends on I2C
help
If you say yes here you get support for Global Mixed-mode
Technology Inc G762 and G763 fan speed PWM controller chips.
This driver can also be built as a module. If so, the module
will be called g762.
config SENSORS_GPIO_FAN
tristate "GPIO fan"
depends on OF_GPIO
depends on GPIOLIB || COMPILE_TEST
depends on THERMAL || THERMAL=n
help
If you say yes here you get support for fans connected to GPIO lines.
This driver can also be built as a module. If so, the module
will be called gpio-fan.
config SENSORS_GXP_FAN_CTRL
tristate "HPE GXP fan controller"
depends on ARCH_HPE_GXP || COMPILE_TEST
help
If you say yes here you get support for GXP fan control functionality.
The GXP controls fan function via the CPLD through the use of PWM
registers. This driver reports status and pwm setting of the fans.
config SENSORS_HIH6130
tristate "Honeywell Humidicon HIH-6130 humidity/temperature sensor"
depends on I2C
help
If you say yes here you get support for Honeywell Humidicon
HIH-6130 and HIH-6131 Humidicon humidity sensors.
This driver can also be built as a module. If so, the module
will be called hih6130.
config SENSORS_HS3001
tristate "Renesas HS3001 humidity and temperature sensors"
depends on I2C
help
If you say yes here you get support for the Renesas HS3001,
to HS3004 humidity and temperature sensors.
This driver can also be built as a module. If so, the module
will be called hs3001.
config SENSORS_IBMAEM
tristate "IBM Active Energy Manager temperature/power sensors and control"
select IPMI_SI
depends on IPMI_HANDLER
help
If you say yes here you get support for the temperature and
power sensors and capping hardware in various IBM System X
servers that support Active Energy Manager. This includes
the x3350, x3550, x3650, x3655, x3755, x3850 M2, x3950 M2,
and certain HC10/HS2x/LS2x/QS2x blades.
This driver can also be built as a module. If so, the module
will be called ibmaem.
config SENSORS_IBMPEX
tristate "IBM PowerExecutive temperature/power sensors"
select IPMI_SI
depends on IPMI_HANDLER
help
If you say yes here you get support for the temperature and
power sensors in various IBM System X servers that support
PowerExecutive. So far this includes the x3350, x3550, x3650,
x3655, and x3755; the x3800, x3850, and x3950 models that have
PCI Express; and some of the HS2x, LS2x, and QS2x blades.
This driver can also be built as a module. If so, the module
will be called ibmpex.
config SENSORS_IBMPOWERNV
tristate "IBM POWERNV platform sensors"
depends on PPC_POWERNV
default y
help
If you say yes here you get support for the temperature/fan/power
sensors on your PowerNV platform.
This driver can also be built as a module. If so, the module
will be called ibmpowernv.
config SENSORS_IIO_HWMON
tristate "Hwmon driver that uses channels specified via iio maps"
depends on IIO
help
This is a platform driver that in combination with a suitable
map allows IIO devices to provide basic hwmon functionality
for those channels specified in the map. This map can be provided
either via platform data or the device tree bindings.
config SENSORS_I5500
tristate "Intel 5500/5520/X58 temperature sensor"
depends on X86 && PCI
help
If you say yes here you get support for the temperature
sensor inside the Intel 5500, 5520 and X58 chipsets.
This driver can also be built as a module. If so, the module
will be called i5500_temp.
config SENSORS_CORETEMP
tristate "Intel Core/Core2/Atom temperature sensor"
depends on X86
help
If you say yes here you get support for the temperature
sensor inside your CPU. Most of the family 6 CPUs
are supported. Check Documentation/hwmon/coretemp.rst for details.
config SENSORS_IT87
tristate "ITE IT87xx and compatibles"
depends on HAS_IOPORT
depends on !PPC
select HWMON_VID
help
If you say yes here you get support for ITE IT8705F, IT8712F, IT8716F,
IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8732F, IT8758E,
IT8771E, IT8772E, IT8781F, IT8782F, IT8783E/F, IT8786E, IT8790E,
IT8603E, IT8620E, IT8623E, and IT8628E sensor chips, and the SiS950
clone.
This driver can also be built as a module. If so, the module
will be called it87.
config SENSORS_JC42
tristate "JEDEC JC42.4 compliant memory module temperature sensors"
depends on I2C
select REGMAP_I2C
help
If you say yes here, you get support for JEDEC JC42.4 compliant
temperature sensors, which are used on many DDR3 memory modules for
mobile devices and servers. Support will include, but not be limited
to, ADT7408, AT30TS00, CAT34TS02, CAT6095, MAX6604, MCP9804, MCP9805,
MCP9808, MCP98242, MCP98243, MCP98244, MCP9843, SE97, SE98,
STTS424(E), STTS2002, STTS3000, TSE2002, TSE2004, TS3000, and TS3001.
This driver can also be built as a module. If so, the module
will be called jc42.
config SENSORS_POWERZ
tristate "ChargerLAB POWER-Z USB-C tester"
depends on USB
help
If you say yes here you get support for ChargerLAB POWER-Z series of
USB-C charging testers.
This driver can also be built as a module. If so, the module
will be called powerz.
config SENSORS_POWR1220
tristate "Lattice POWR1220 Power Monitoring"
depends on I2C
help
If you say yes here you get access to the hardware monitoring
functions of the Lattice POWR1220 isp Power Supply Monitoring,
Sequencing and Margining Controller.
This driver can also be built as a module. If so, the module
will be called powr1220.
config SENSORS_LAN966X
tristate "Microchip LAN966x Hardware Monitoring"
depends on SOC_LAN966 || COMPILE_TEST
select REGMAP
select POLYNOMIAL
help
If you say yes here you get support for temperature monitoring
on the Microchip LAN966x SoC.
This driver can also be built as a module. If so, the module
will be called lan966x-hwmon.
config SENSORS_LENOVO_EC
tristate "Sensor reader for Lenovo ThinkStations"
depends on X86
help
If you say yes here you get support for LENOVO
EC Sensor data on newer ThinkStation systems
This driver can also be built as a module. If so, the module
will be called lenovo_ec_sensors.
config SENSORS_LINEAGE
tristate "Lineage Compact Power Line Power Entry Module"
depends on I2C
help
If you say yes here you get support for the Lineage Compact Power Line
series of DC/DC and AC/DC converters such as CP1800, CP2000AC,
CP2000DC, CP2725, and others.
This driver can also be built as a module. If so, the module
will be called lineage-pem.
config SENSORS_LOCHNAGAR
tristate "Lochnagar Hardware Monitor"
depends on MFD_LOCHNAGAR
help
If you say yes here you get support for Lochnagar 2 temperature,
voltage and current sensors abilities.
This driver can also be built as a module. If so, the module
will be called lochnagar-hwmon.
config SENSORS_LTC2945
tristate "Linear Technology LTC2945"
depends on I2C
select REGMAP_I2C
help
If you say yes here you get support for Linear Technology LTC2945
I2C System Monitor.
This driver can also be built as a module. If so, the module will
be called ltc2945.
config SENSORS_LTC2947
tristate
config SENSORS_LTC2947_I2C
tristate "Analog Devices LTC2947 High Precision Power and Energy Monitor over I2C"
depends on I2C
select REGMAP_I2C
select SENSORS_LTC2947
help
If you say yes here you get support for Linear Technology LTC2947
I2C High Precision Power and Energy Monitor
This driver can also be built as a module. If so, the module will
be called ltc2947-i2c.
config SENSORS_LTC2947_SPI
tristate "Analog Devices LTC2947 High Precision Power and Energy Monitor over SPI"
depends on SPI_MASTER
select REGMAP_SPI
select SENSORS_LTC2947
help
If you say yes here you get support for Linear Technology LTC2947
SPI High Precision Power and Energy Monitor
This driver can also be built as a module. If so, the module will
be called ltc2947-spi.
config SENSORS_LTC2990
tristate "Linear Technology LTC2990"
depends on I2C
help
If you say yes here you get support for Linear Technology LTC2990
I2C System Monitor. The LTC2990 supports a combination of voltage,
current and temperature monitoring.
This driver can also be built as a module. If so, the module will
be called ltc2990.
config SENSORS_LTC2991