+AdcParam<a class="cmnd" id="adcparam"></a>|[ADC](ADC) analog input tuning parameters<br>`<sensor>, <param1>, <param2>, <param3>, <param4>`<BR>`<sensor>` values:<br>  `2` = Temperature [Steinhart-Hart thermistor equation](https://en.wikipedia.org/wiki/Steinhart%E2%80%93Hart_equation) parameters:</li><ul>`<param1>` = NTC Voltage bridge resistor in Ohms *(default = `32000`)*<br>`<param2>` = NTC Resistance in Ohms *(default = `10000`)*<BR>`<param3>` = NTC Beta Coefficient *(default = `3350`)*</li></ul><br>  `3` = Light [Lux equation](https://www.allaboutcircuits.com/projects/design-a-luxmeter-using-a-light-dependent-resistor/) parameters:</li><ul>`<param1>` = LDR Voltage bridge resistor in Ohms *(default = `10000`)*<BR>`<param2>` = LDR Lux Scalar *(default = `12518931`)*<BR>`<param3>` = LDR Lux Exponent *(default = `-1.4050`)*</li></ul><br>  `6` = ADC linear range remapping parameters:</li><ul>`<param1>` = input range low value `adcLow` *(default = `0`)*<BR>`<param2>` = input range high value `adcHigh` *(default = `1023`)*<BR>`<param3>` = output range low value `rangeLow` *(default = `0`)*<BR>`<param4>` = output range high value `rangeHigh` *(default = `100`)*<BR>The range remapping perform the following calculation on the ADC value *[0..1023]*:<BR>`Range = ((adcHigh - ADC) / (adcHigh - adcLow)) * (rangeLow - rangeHigh) + rangeHigh`<br>*The calculation is performed in double resolution floating point but all 4 parameters as well as the range output are unsigned 16 bit integers. The calculation result must not exceed [0..65535].*<BR>Example to convert the ADC value on a D1-mini into millivolts (using the default resistor bridge of 220k/100k):<BR>`AdcParam 6, 0, 1023, 0, 3200`</li></ul><br>  `7` = CT POWER parameter adjustments:</li><ul>`<param1>` = ANALOG_CT_FLAGS (default 0 for a non-invasive current sensor). When value is `>0` its sets the `adcLow` value as base for the measurement via OpAmp differential amplifier.<BR>`<param2>` = ANALOG_CT_MULTIPLIER ( 2146 = Default settings for a (AC) 20A/1V Current Transformer.) multiplier\*100000 to convert raw ADC peak to peak range 0..1023 to RMS current in Amps. Value of 100000 corresponds to 1<BR>`<param3>` = ANALOG_CT_VOLTAGE (default 2300) to convert current in Amps to apparent power in Watts using voltage in Volts*10. Value of 2200 corresponds to AC220V. For DC its Volt/1000. Eg. 12VDC = 0.012.<BR> `AdcParam 7,406,3282,0.012`</li></ul><BR>  `9` = ANALOG_PH parameter adjustments:</li><ul>`<param1>` = ANALOG_PH_CALSOLUTION_LOW_PH (default 4.0).<BR>`<param2>` = ANALOG_PH_CALSOLUTION_LOW_ANALOG_VALUE ( default 282 )<BR>`<param3>` = ANALOG_PH_CALSOLUTION_HIGH_PH (default 9.18).<BR>`<param4>` = ANALOG_PH_CALSOLUTION_HIGH_ANALOG_VALUE (default 435).<BR><BR>To calibrate the probe, two reference solutions with known pH are required. Calibration procedure: <ol><li>Put probe in solution with lower pH value. pH value of the solution is ANALOG_PH_CALSOLUTION_LOW_PH.</li><li>Wait until analog value / RAW value stabilizes (~3 minutes)</li><li>The analog reading is ANALOG_PH_CALSOLUTION_LOW_ANALOG_VALUE</li><li>Clean probe and put in solution with higher pH value. pH value of the solution is ANALOG_PH_CALSOLUTION_HIGH_PH.</li><li>Wait until analog value / RAW value stabilizes (~3 minutes)</li><li>The analog reading is ANALOG_PH_CALSOLUTION_HIGH_ANALOG_VALUE</li></ol>Analog readings can be read by either changing the analog port configuration to "Analog Input" while calibrating, or by enabling debug logs in the console and having a look at the `RAW Value`reading instead.<BR>
0 commit comments