ATtiny_Slow_PWM Library

Important Note for Arduino IDE
Why do we need this ATtiny_Slow_PWM library
- Features
- Why using ISR-based PWM is better
- Currently supported Boards
- Important Notes about ISR
Changelog
Prerequisites
Installation
- Use Arduino Library Manager
- Manual Install
- VS Code & PlatformIO
HOWTO Fix Multiple Definitions Linker Error
More useful Information
- 1. Documents
- 2. Timer TCB0-TCB1
Usage
- 1. Init Hardware Timer
- 2. Set PWM Frequency, dutycycle, attach irqCallbackStartFunc and irqCallbackStopFunc functions
Examples
- 1. ISR_8_PWMs_Array
- 2. ISR_8_PWMs_Array_Complex
- 3. ISR_8_PWMs_Array_Simple
- 4. ISR_Changing_PWM
- 5. ISR_Modify_PWM
- 6. multiFileProject. New
Example ISR_8_PWMs_Array_Complex
Debug Terminal Output Samples
- 1. ISR_8_PWMs_Array_Complex on AVR_ATtiny3217
- 2. ISR_8_PWMs_Array on AVR_ATtiny3217
- 3. ISR_8_PWMs_Array_Simple on AVR_ATtiny3217
- 4. ISR_Modify_PWM on AVR_ATtiny3217
- 5. ISR_Changing_PWM on AVR_ATtiny3217
Debug
Troubleshooting
Issues
TO DO
DONE
Contributions and Thanks
Contributing
License
Copyright

Important Note for Arduino IDE

With some Arduino IDE versions, such as v1.8.19, upload directly via USB to some boards, such as AVR_CuriosityNano3217 can't be done without unknown-to-me fix. We'll get the following error when uploading

avrdude: Version 6.3-20201216
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/home/kh/.arduino15/packages/megaTinyCore/hardware/megaavr/2.5.11/avrdude.conf"
         User configuration file is "/home/kh/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : usb
         Using Programmer              : curiosity_updi
avrdude: usbdev_open(): Found nEDBG CMSIS-DAP, serno: MCHP3333021800000998
avrdude: usbdev_open(): WARNING: failed to set configuration 1: Device or resource busy
avrdude: Found CMSIS-DAP compliant device, using EDBG protocol
avrdude: usbdev_send(): wrote -5 out of 912 bytes, err = Input/output error
avrdude: jtag3_edbg_prepare(): failed to send command to serial port

avrdude done.  Thank you.

the selected serial port 
 does not exist or your board is not connected

We can use drag-and-drop method to drag-and-drop the compiled hex file to CURIOSITY virtual drive.

If success, The LED blinks slowly for 2 sec, or rapidly for 2 sec if failure

For example, to run Change_Interval example, use Arduino IDE to compile, and get the Change_Interval.ino.hex file. For Ubuntu Linux, the file is stored in directory /tmp/arduino_build_xxxxxx

After drag-and-drop the Change_Interval.ino.hex into CURIOSITY virtual drive, the code will run immediately if successfully loaded (LED blinks slowly)

Why do we need this ATtiny_Slow_PWM library

Features

This library enables you to use ISR-based PWM channels on Arduino AVR ATtiny-based boards (ATtiny3217, etc.) using megaTinyCore, to create and output PWM any GPIO pin. Because this library doesn't use the powerful, high-speed, purely hardware-controlled PWM with many limitations, the maximum PWM frequency is currently limited at 1000Hz, which is still suitable for many real-life applications, such as LED lighting, Servo, etc. Now you can change the PWM settings on-the-fly

This library enables you to use Interrupt from Hardware Timers on AVR ATtiny-based boards to create and output PWM to any pins. It now supports 64 ISR-based synchronized PWM channels, while consuming only 1 Hardware Timer. PWM interval can be very long (uint64_t microsecs / millisecs). The most important feature is they're ISR-based PWM channels. Therefore, their executions are not blocked by bad-behaving functions or tasks. This important feature is absolutely necessary for mission-critical tasks. These hardware PWM channels, using interrupt, still work even if other functions are blocking. Moreover, they are much more precise (certainly depending on clock frequency accuracy) than other software PWM using millis() or micros(). That's necessary if you need to measure some data requiring better accuracy.

As Hardware Timers are rare, and very precious assets of any board, this library now enables you to use up to 64 ISR-based synchronized PWM channels, while consuming only 1 Hardware Timer. Timers' interval is very long (ulong millisecs).

Now with these new 64 ISR-based PWM-channels, the maximum interval is practically unlimited (limited only by uint64_t milliseconds) while the accuracy is nearly perfect compared to software PWM channels.

The most important feature is they're ISR-based PWM channels. Therefore, their executions are not blocked by bad-behaving functions / tasks, such as connecting to WiFi, Internet or Blynk services. This important feature is absolutely necessary for mission-critical tasks. You can also have many (up to 64) PWM channels to use.

This non-being-blocked important feature is absolutely necessary for mission-critical tasks.

The ISR_8_PWMs_Array_Complex example will demonstrate the nearly perfect accuracy, compared to software PWM, by printing the actual period / duty-cycle in microsecs of each of PWM-channels.

You'll see software-based SimpleTimer is blocked while system is connecting to WiFi / Internet / Blynk, as well as by blocking task in loop(), using delay() function as an example. The elapsed time then is very unaccurate

Why using ISR-based PWM is better

Imagine you have a system with a mission-critical function, measuring water level and control the sump pump or doing something much more important. You normally use a software timer to poll, or even place the function in loop(). But what if another function is blocking the loop() or setup().

So your function might not be executed, and the result would be disastrous.

You'd prefer to have your function called, no matter what happening with other functions (busy loop, bug, etc.).

The correct choice is to use a Hardware Timer with Interrupt to call your function.

These hardware PWM channels, using interrupt, still work even if other functions are blocking. Moreover, they are much more precise (certainly depending on clock frequency accuracy) than other software PWM channels using millis() or micros(). That's necessary if you need to measure some data requiring better accuracy.

Functions using normal software PWM channels, relying on loop() and calling millis(), won't work if the loop() or setup() is blocked by certain operation. For example, certain function is blocking while it's connecting to WiFi or some services.

The catch is your function is now part of an ISR (Interrupt Service Routine), and must be lean / mean, and follow certain rules. More to read on:

HOWTO Attach Interrupt

Currently supported Boards

tinyAVR boards using megaTinyCore

Curiosity Nano ATtiny3217

Important Notes about ISR

Inside the attached function, delay() won’t work and the value returned by millis() will not increment. Serial data received while in the function may be lost. You should declare as volatile any variables that you modify within the attached function.
Typically global variables are used to pass data between an ISR and the main program. To make sure variables shared between an ISR and the main program are updated correctly, declare them as volatile.

Prerequisites

Arduino IDE 1.8.19+ for Arduino.
SpenceKonde megaTinyCore core 2.6.4+ for Arduino ATtiny boards. . Follow megaTinyCore Installation.
To use with certain example
- SimpleTimer library for ISR_8_PWMs_Array_Simple and ISR_8_PWMs_Array_Complex examples.

Installation

Use Arduino Library Manager

The best and easiest way is to use Arduino Library Manager. Search for ATtiny_Slow_PWM, then select / install the latest version. You can also use this link for more detailed instructions.

Manual Install

Another way to install is to:

Navigate to ATtiny_Slow_PWM page.
Download the latest release ATtiny_Slow_PWM-main.zip.
Extract the zip file to ATtiny_Slow_PWM-main directory
Copy whole ATtiny_Slow_PWM-main folder to Arduino libraries' directory such as ~/Arduino/libraries/.

VS Code & PlatformIO

Install VS Code
Install PlatformIO
Install ATtiny_Slow_PWM library by using Library Manager. Search for ATtiny_Slow_PWM in Platform.io Author's Libraries
Use included platformio.ini file from examples to ensure that all dependent libraries will installed automatically. Please visit documentation for the other options and examples at Project Configuration File

HOWTO Fix `Multiple Definitions` Linker Error

The current library implementation, using xyz-Impl.h instead of standard xyz.cpp, possibly creates certain Multiple Definitions Linker error in certain use cases.

You can include this .hpp file

// Can be included as many times as necessary, without `Multiple Definitions` Linker Error
#include "ATtiny_Slow_PWM.hpp"          //https://github.com/khoih-prog/ATtiny_Slow_PWM

in many files. But be sure to use the following .h file in just 1 .h, .cpp or .ino file, which must not be included in any other file, to avoid Multiple Definitions Linker Error

// To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error
#include "ATtiny_Slow_PWM.h"            //https://github.com/khoih-prog/ATtiny_Slow_PWM

Check the new multiFileProject example for a HOWTO demo.

Have a look at the discussion in Different behaviour using the src_cpp or src_h lib #80

More useful Information

1. Documents

2. Timer TCB0-TCB1

TCB0-TCB1 are 16-bit timers

The ATtiny boards, such as ATtiny3217, ATtiny1617, will have only maximum 2 TCB timers, (TCB0-TCB1).

The ATtiny boards, such as ATtiny817, will have only maximum 1 TCB timer, (TCB0).

The number of TCB timers will be automatically configured by the library.

The following is the partial list of number of TCBs for each ATtiny board/chip

TCB0-TCB1, TCA, TCD

ATtiny3217, ATtiny1617, ATtiny3216, ATtiny1616, ATtiny1614

TCB0, TCA, TCD

ATtinyx12, ATtinyx14, ATtinyx16, ATtinyx17, such as ATtiny817, ATtiny417, ATtiny816, etc.

TCB0, TCA, no TCD

ATtinyx02, ATtinyx04, ATtinyx06, ATtinyx07, such as ATtiny1607, ATtiny807, ATtiny1606, etc.

Usage

Before using any Timer, you have to make sure the Timer has not been used by any other purpose.

1. Init Hardware Timer

// Select USING_FULL_CLOCK      == true for  20/16MHz to Timer TCBx => shorter timer, but better accuracy
// Select USING_HALF_CLOCK      == true for  10/ 8MHz to Timer TCBx => shorter timer, but better accuracy
// Select USING_250KHZ          == true for 250KHz to Timer TCBx => longer timer,  but worse  accuracy
// Not select for default 250KHz to Timer TCBx => longer timer,  but worse accuracy
#define USING_FULL_CLOCK      true
#define USING_HALF_CLOCK      false
#define USING_250KHZ          false         // Not supported now

// Try to use RTC, TCA0 or TCD0 for millis()
#define USE_TIMER_0           true          // Check if used by millis(), Servo or tone()
#define USE_TIMER_1           false         // Check if used by millis(), Servo or tone()

#if USE_TIMER_0
  #define CurrentTimer   ITimer0
#elif USE_TIMER_1
  #define CurrentTimer   ITimer1
#else
  #error You must select one Timer  
#endif

// To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error
#include "ATtiny_Slow_PWM.h"

// Init AT_TINY_SLOW_PWM, each can service max 64 different ISR-based PWM channels
AT_TINY_SLOW_PWM_ISR ISR_PWM;

2. Set PWM Frequency, dutycycle, attach irqCallbackStartFunc and irqCallbackStopFunc functions

void irqCallbackStartFunc()
{

}

void irqCallbackStopFunc()
{

}

void setup()
{
  ....
  
  // You can use this with PWM_Freq in Hz
  ISR_PWM.setPWM(PWM_Pin, PWM_Freq, PWM_DutyCycle, irqCallbackStartFunc, irqCallbackStopFunc);
                   
  ....                 
}

Examples:

Example ISR_8_PWMs_Array_Complex

ATtiny_Slow_PWM/examples/ISR_8_PWMs_Array_Complex/ISR_8_PWMs_Array_Complex.ino

Lines 16 to 481 in 137d892

    
           // Important Note: To use drag-and-drop into CURIOSITY virtual drive if you can program via Arduino IDE 
        
           // For example, check https://ww1.microchip.com/downloads/en/DeviceDoc/40002193A.pdf 
        
           #if !( defined(MEGATINYCORE) ) 
        
             #error This is designed only for MEGATINYCORE megaAVR board! Please check your Tools->Board setting 
        
           #endif 
        
           // These define's must be placed at the beginning before #include "ATtiny_Slow_PWM.h" 
        
           // _PWM_LOGLEVEL_ from 0 to 4 
        
           // Don't define _PWM_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system. 
        
           #define _PWM_LOGLEVEL_      0 
        
           // Be careful when using MAX_NUMBER_CHANNELS > 16. Max pemissible MAX_NUMBER_CHANNELS is 64 
        
           #define MAX_NUMBER_CHANNELS        16 
        
           // Select USING_FULL_CLOCK      == true for  20/16MHz to Timer TCBx => shorter timer, but better accuracy 
        
           // Select USING_HALF_CLOCK      == true for  10/ 8MHz to Timer TCBx => shorter timer, but better accuracy 
        
           // Select USING_250KHZ          == true for 250KHz to Timer TCBx => longer timer,  but worse  accuracy 
        
           // Not select for default 250KHz to Timer TCBx => longer timer,  but worse accuracy 
        
           #define USING_FULL_CLOCK      true 
        
           #define USING_HALF_CLOCK      false 
        
           #define USING_250KHZ          false         // Not supported now 
        
           // Try to use RTC, TCA0 or TCD0 for millis() 
        
           #define USE_TIMER_0           true          // Check if used by millis(), Servo or tone() 
        
           #define USE_TIMER_1           false         // Check if used by millis(), Servo or tone() 
        
           #if USE_TIMER_0 
        
             #define CurrentTimer   ITimer0 
        
           #elif USE_TIMER_1 
        
             #define CurrentTimer   ITimer1 
        
           #else 
        
             #error You must select one Timer   
        
           #endif 
        
           #define USING_MICROS_RESOLUTION       true  //false  
        
           // To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error 
        
           #include "ATtiny_Slow_PWM.h" 
        
           #include <SimpleTimer.h>              // https://github.com/jfturcot/SimpleTimer 
        
           #define LED_OFF             HIGH 
        
           #define LED_ON              LOW 
        
           #ifdef LED_BUILTIN 
        
             #undef LED_BUILTIN 
        
             // To modify according to your board 
        
             // For Curiosity Nano ATtiny3217 => PIN_PA3 
        
             #if defined(ARDUINO_AVR_CuriosityNano3217)  
        
               #define LED_BUILTIN   PIN_PA3 
        
             #else 
        
               // standard Arduino pin 13 
        
               #define LED_BUILTIN   PIN_PA3 
        
             #endif 
        
           #endif 
        
           #define USING_HW_TIMER_INTERVAL_MS        false   //true 
        
           // Don't change these numbers to make higher Timer freq. System can hang 
        
           #define HW_TIMER_INTERVAL_MS        0.0333f 
        
           #define HW_TIMER_INTERVAL_FREQ      30000L 
        
           volatile uint32_t startMicros = 0; 
        
           // Init AT_TINY_SLOW_PWM, each can service max 64 different ISR-based PWM channels 
        
           AT_TINY_SLOW_PWM_ISR ISR_PWM; 
        
           ////////////////////////////////////////////////////// 
        
           void TimerHandler() 
        
           { 
        
             ISR_PWM.run(); 
        
           } 
        
           ///////////////////////////////////////////////// 
        
           #define PIN_D0      0 
        
           #define PIN_D1      1 
        
           #define PIN_D2      2 
        
           #define PIN_D3      3 
        
           #define PIN_D4      4 
        
           #define PIN_D5      5 
        
           #define PIN_D6      6 
        
           // You can assign pins here. Be careful to select good pin to use or crash, e.g pin 6-11 
        
           uint32_t PWM_Pin[] = 
        
           { 
        
             LED_BUILTIN, PIN_D0, PIN_D1,  PIN_D2,  PIN_D3,  PIN_D4,  PIN_D5,  PIN_D6 
        
           }; 
        
           #define NUMBER_ISR_PWMS         ( sizeof(PWM_Pin) / sizeof(uint32_t) ) 
        
           typedef void (*irqCallback)  (); 
        
           ////////////////////////////////////////////////////// 
        
           #define USE_COMPLEX_STRUCT      true 
        
           ////////////////////////////////////////////////////// 
        
           #if USE_COMPLEX_STRUCT 
        
           typedef struct 
        
           { 
        
             uint32_t      PWM_Pin; 
        
             irqCallback   irqCallbackStartFunc; 
        
             irqCallback   irqCallbackStopFunc; 
        
             uint32_t      PWM_Freq; 
        
             uint32_t      PWM_DutyCycle; 
        
             uint32_t      deltaMicrosStart; 
        
             uint32_t      previousMicrosStart; 
        
             uint32_t      deltaMicrosStop; 
        
             uint32_t      previousMicrosStop; 
        
           } ISR_PWM_Data; 
        
           // In AVRDx, avoid doing something fancy in ISR, for example Serial.print() 
        
           // The pure simple Serial.prints here are just for demonstration and testing. Must be eliminate in working environment 
        
           // Or you can get this run-time error / crash 
        
           void doingSomethingStart(int index); 
        
           void doingSomethingStop(int index); 
        
           #else   // #if USE_COMPLEX_STRUCT 
        
           volatile unsigned long deltaMicrosStart    [] = { 0, 0, 0, 0, 0, 0, 0, 0 }; 
        
           volatile unsigned long previousMicrosStart [] = { 0, 0, 0, 0, 0, 0, 0, 0 }; 
        
           volatile unsigned long deltaMicrosStop     [] = { 0, 0, 0, 0, 0, 0, 0, 0 }; 
        
           volatile unsigned long previousMicrosStop  [] = { 0, 0, 0, 0, 0, 0, 0, 0 }; 
        
           // You can assign any interval for any timer here, in Microseconds 
        
           uint32_t PWM_Period[] = 
        
           { 
        
             1000L,   500L,   333L,   250L,   200L,   166L,   142L,   125L 
        
           }; 
        
           // You can assign any interval for any timer here, in Hz 
        
           float PWM_Freq[] = 
        
           { 
        
             1.0f,  2.0f,  3.0f,  4.0f,  5.0f,  6.0f,  7.0f,  8.0f, 
        
           }; 
        
           // You can assign any interval for any timer here, in Microseconds 
        
           float PWM_DutyCycle[] = 
        
           { 
        
             5.0, 10.0, 20.0, 30.0, 40.0, 45.0, 50.0, 55.0 
        
           }; 
        
           void doingSomethingStart(int index) 
        
           { 
        
             unsigned long currentMicros  = micros(); 
        
             deltaMicrosStart[index]    = currentMicros - previousMicrosStart[index]; 
        
             previousMicrosStart[index] = currentMicros; 
        
           } 
        
           void doingSomethingStop(int index) 
        
           { 
        
             unsigned long currentMicros  = micros(); 
        
             // Count from start to stop PWM pulse 
        
             deltaMicrosStop[index]    = currentMicros - previousMicrosStart[index]; 
        
             previousMicrosStop[index] = currentMicros; 
        
           } 
        
           #endif    // #if USE_COMPLEX_STRUCT 
        
           //////////////////////////////////// 
        
           // Shared 
        
           //////////////////////////////////// 
        
           void doingSomethingStart0() 
        
           { 
        
             doingSomethingStart(0); 
        
           } 
        
           void doingSomethingStart1() 
        
           { 
        
             doingSomethingStart(1); 
        
           } 
        
           void doingSomethingStart2() 
        
           { 
        
             doingSomethingStart(2); 
        
           } 
        
           void doingSomethingStart3() 
        
           { 
        
             doingSomethingStart(3); 
        
           } 
        
           void doingSomethingStart4() 
        
           { 
        
             doingSomethingStart(4); 
        
           } 
        
           void doingSomethingStart5() 
        
           { 
        
             doingSomethingStart(5); 
        
           } 
        
           void doingSomethingStart6() 
        
           { 
        
             doingSomethingStart(6); 
        
           } 
        
           void doingSomethingStart7() 
        
           { 
        
             doingSomethingStart(7); 
        
           } 
        
           ////////////////////////////////////////////////////// 
        
           void doingSomethingStop0() 
        
           { 
        
             doingSomethingStop(0); 
        
           } 
        
           void doingSomethingStop1() 
        
           { 
        
             doingSomethingStop(1); 
        
           } 
        
           void doingSomethingStop2() 
        
           { 
        
             doingSomethingStop(2); 
        
           } 
        
           void doingSomethingStop3() 
        
           { 
        
             doingSomethingStop(3); 
        
           } 
        
           void doingSomethingStop4() 
        
           { 
        
             doingSomethingStop(4); 
        
           } 
        
           void doingSomethingStop5() 
        
           { 
        
             doingSomethingStop(5); 
        
           } 
        
           void doingSomethingStop6() 
        
           { 
        
             doingSomethingStop(6); 
        
           } 
        
           void doingSomethingStop7() 
        
           { 
        
             doingSomethingStop(7); 
        
           } 
        
           ////////////////////////////////////////////////////// 
        
           #if USE_COMPLEX_STRUCT 
        
           ISR_PWM_Data curISR_PWM_Data[] = 
        
           { 
        
             // pin, irqCallbackStartFunc, irqCallbackStopFunc, PWM_Freq, PWM_DutyCycle, deltaMicrosStart, previousMicrosStart, deltaMicrosStop, previousMicrosStop 
        
             { LED_BUILTIN,  doingSomethingStart0,    doingSomethingStop0,    1,   5, 0, 0, 0, 0 }, 
        
             { PIN_D0,       doingSomethingStart1,    doingSomethingStop1,    2,  10, 0, 0, 0, 0 }, 
        
             { PIN_D1,       doingSomethingStart2,    doingSomethingStop2,    3,  20, 0, 0, 0, 0 }, 
        
             { PIN_D2,       doingSomethingStart3,    doingSomethingStop3,    4,  30, 0, 0, 0, 0 }, 
        
             { PIN_D3,       doingSomethingStart4,    doingSomethingStop4,    5,  40, 0, 0, 0, 0 }, 
        
             { PIN_D4,       doingSomethingStart5,    doingSomethingStop5,    6,  45, 0, 0, 0, 0 }, 
        
             { PIN_D5,       doingSomethingStart6,    doingSomethingStop6,    7,  50, 0, 0, 0, 0 }, 
        
             { PIN_D6,       doingSomethingStart7,    doingSomethingStop7,    8,  55, 0, 0, 0, 0 }, 
        
           }; 
        
           void doingSomethingStart(int index) 
        
           { 
        
             unsigned long currentMicros  = micros(); 
        
             curISR_PWM_Data[index].deltaMicrosStart    = currentMicros - curISR_PWM_Data[index].previousMicrosStart; 
        
             curISR_PWM_Data[index].previousMicrosStart = currentMicros; 
        
           } 
        
           void doingSomethingStop(int index) 
        
           { 
        
             unsigned long currentMicros  = micros(); 
        
             //curISR_PWM_Data[index].deltaMicrosStop     = currentMicros - curISR_PWM_Data[index].previousMicrosStop; 
        
             // Count from start to stop PWM pulse 
        
             curISR_PWM_Data[index].deltaMicrosStop     = currentMicros - curISR_PWM_Data[index].previousMicrosStart; 
        
             curISR_PWM_Data[index].previousMicrosStop  = currentMicros; 
        
           } 
        
           #else   // #if USE_COMPLEX_STRUCT 
        
           irqCallback irqCallbackStartFunc[] = 
        
           { 
        
             doingSomethingStart0,  doingSomethingStart1,  doingSomethingStart2,  doingSomethingStart3, 
        
             doingSomethingStart4,  doingSomethingStart5,  doingSomethingStart6,  doingSomethingStart7 
        
           }; 
        
           irqCallback irqCallbackStopFunc[] = 
        
           { 
        
             doingSomethingStop0,  doingSomethingStop1,  doingSomethingStop2,  doingSomethingStop3, 
        
             doingSomethingStop4,  doingSomethingStop5,  doingSomethingStop6,  doingSomethingStop7 
        
           }; 
        
           #endif    // #if USE_COMPLEX_STRUCT 
        
           ////////////////////////////////////////////////////// 
        
           #define SIMPLE_TIMER_MS        2000L 
        
           // Init SimpleTimer 
        
           SimpleTimer simpleTimer; 
        
           // Here is software Timer, you can do somewhat fancy stuffs without many issues. 
        
           // But always avoid 
        
           // 1. Long delay() it just doing nothing and pain-without-gain wasting CPU power.Plan and design your code / strategy ahead 
        
           // 2. Very long "do", "while", "for" loops without predetermined exit time. 
        
           void simpleTimerDoingSomething2s() 
        
           { 
        
             static unsigned long previousMicrosStart = startMicros; 
        
             unsigned long currMicros = micros(); 
        
             Serial.print(F("SimpleTimer (us): ")); Serial.print(SIMPLE_TIMER_MS); 
        
             Serial.print(F(", us : ")); Serial.print(currMicros); 
        
             Serial.print(F(", Dus : ")); Serial.println(currMicros - previousMicrosStart); 
        
             for (uint16_t i = 0; i < NUMBER_ISR_PWMS; i++) 
        
             { 
        
           #if USE_COMPLEX_STRUCT 
        
               Serial.print(F("PWM Channel : ")); Serial.print(i); 
        
               Serial.print(F(", prog Period (ms): ")); 
        
               Serial.print(1000.f / curISR_PWM_Data[i].PWM_Freq); 
        
               Serial.print(F(", actual : ")); Serial.print((uint32_t) curISR_PWM_Data[i].deltaMicrosStart); 
        
               Serial.print(F(", prog DutyCycle : ")); 
        
               Serial.print(curISR_PWM_Data[i].PWM_DutyCycle); 
        
               Serial.print(F(", actual : ")); Serial.println((float) curISR_PWM_Data[i].deltaMicrosStop * 100.0f / curISR_PWM_Data[i].deltaMicrosStart); 
        
               //Serial.print(F(", actual deltaMicrosStop : ")); Serial.println(curISR_PWM_Data[i].deltaMicrosStop); 
        
               //Serial.print(F(", actual deltaMicrosStart : ")); Serial.println(curISR_PWM_Data[i].deltaMicrosStart); 
        
           #else 
        
               Serial.print(F("PWM Channel : ")); Serial.print(i); 
        
               Serial.print(1000 / PWM_Freq[i]); 
        
               Serial.print(F(", prog. Period (us): ")); Serial.print(PWM_Period[i]); 
        
               Serial.print(F(", actual : ")); Serial.print(deltaMicrosStart[i]); 
        
               Serial.print(F(", prog DutyCycle : ")); 
        
               Serial.print(PWM_DutyCycle[i]); 
        
               Serial.print(F(", actual : ")); Serial.println( (float) deltaMicrosStop[i] * 100.0f / deltaMicrosStart[i]); 
        
               //Serial.print(F(", actual deltaMicrosStop : ")); Serial.println(deltaMicrosStop[i]); 
        
               //Serial.print(F(", actual deltaMicrosStart : ")); Serial.println(deltaMicrosStart[i]); 
        
           #endif 
        
             } 
        
             previousMicrosStart = currMicros; 
        
           } 
        
           void setup() 
        
           { 
        
             Serial.begin(115200); 
        
             while (!Serial && millis() < 5000); 
        
             Serial.print(F("\nStarting ISR_8_PWMs_Array_Complex on ")); Serial.println(BOARD_NAME); 
        
             Serial.println(AT_TINY_SLOW_PWM_VERSION); 
        
             Serial.print(F("CPU Frequency = ")); Serial.print(F_CPU / 1000000); Serial.println(F(" MHz")); 
        
             Serial.print(F("Max number PWM channels = ")); Serial.println(MAX_NUMBER_CHANNELS); 
        
             Serial.print(F("TCB Clock Frequency = "));  
        
           #if USING_FULL_CLOCK   
        
             Serial.println(F("Full clock (20/16MHz, etc) for highest accuracy")); 
        
           #elif USING_HALF_CLOCK   
        
             Serial.println(F("Half clock (10/8MHz, etc.) for high accuracy")); 
        
           #else 
        
             Serial.println(F("250KHz for lower accuracy but longer time")); 
        
           #endif 
        
           #if USING_HW_TIMER_INTERVAL_MS 
        
             CurrentTimer.init(); 
        
             if (CurrentTimer.attachInterruptInterval(HW_TIMER_INTERVAL_MS, TimerHandler)) 
        
             { 
        
               Serial.print(F("Starting ITimer OK, micros() = ")); Serial.println(micros()); 
        
             } 
        
             else 
        
               Serial.println(F("Can't set ITimer. Select another freq. or timer")); 
        
           #else 
        
             CurrentTimer.init(); 
        
             if (CurrentTimer.attachInterrupt(HW_TIMER_INTERVAL_FREQ, TimerHandler)) 
        
             { 
        
               Serial.print(F("Starting ITimer OK, micros() = ")); Serial.println(micros()); 
        
             } 
        
             else 
        
               Serial.println(F("Can't set ITimer. Select another freq. or timer")); 
        
           #endif    // USING_HW_TIMER_INTERVAL_MS 
        
             startMicros = micros(); 
        
             // Just to demonstrate, don't use too many ISR Timers if not absolutely necessary 
        
             // You can use up to 16 timer for each ISR_PWM 
        
             for (uint16_t i = 0; i < NUMBER_ISR_PWMS; i++) 
        
             { 
        
           #if USE_COMPLEX_STRUCT 
        
               curISR_PWM_Data[i].previousMicrosStart = startMicros; 
        
               //ISR_PWM.setInterval(curISR_PWM_Data[i].PWM_Period, curISR_PWM_Data[i].irqCallbackStartFunc); 
        
               //void setPWM(uint32_t pin, float frequency, float dutycycle 
        
               // , timer_callback_p StartCallback = nullptr, timer_callback_p StopCallback = nullptr) 
        
               // You can use this with PWM_Freq in Hz 
        
               ISR_PWM.setPWM(curISR_PWM_Data[i].PWM_Pin, curISR_PWM_Data[i].PWM_Freq, curISR_PWM_Data[i].PWM_DutyCycle, 
        
                              curISR_PWM_Data[i].irqCallbackStartFunc, curISR_PWM_Data[i].irqCallbackStopFunc); 
        
           #else 
        
               previousMicrosStart[i] = micros(); 
        
               // You can use this with PWM_Freq in Hz 
        
               ISR_PWM.setPWM(PWM_Pin[i], PWM_Freq[i], PWM_DutyCycle[i], irqCallbackStartFunc[i], irqCallbackStopFunc[i]); 
        
           #endif 
        
             } 
        
             // You need this timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary. 
        
             simpleTimer.setInterval(SIMPLE_TIMER_MS, simpleTimerDoingSomething2s); 
        
           } 
        
           #define BLOCKING_TIME_MS      10000L 
        
           void loop() 
        
           { 
        
             // This unadvised blocking task is used to demonstrate the blocking effects onto the execution and accuracy to Software timer 
        
             // You see the time elapse of ISR_PWM still accurate, whereas very unaccurate for Software Timer 
        
             // The time elapse for 2000ms software timer now becomes 3000ms (BLOCKING_TIME_MS) 
        
             // While that of ISR_PWM is still prefect. 
        
             delay(BLOCKING_TIME_MS); 
        
             // You need this Software timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary 
        
             // You don't need to and never call ISR_PWM.run() here in the loop(). It's already handled by ISR timer. 
        
             simpleTimer.run(); 
        
           }

Debug Terminal Output Samples

1. ISR_8_PWMs_Array_Complex on AVR_ATtiny3217

The following is the sample terminal output when running example ISR_8_PWMs_Array_Complex Curiosity Nano AVR_ATtiny3217 to demonstrate how to use multiple PWM channels with complex callback functions, the accuracy of ISR Hardware PWM-channels, especially when system is very busy. The ISR PWM-channels is running exactly according to corresponding programmed periods and duty-cycles

Starting ISR_8_PWMs_Array_Complex on AVR_ATtiny3217
ATtiny_Slow_PWM v1.0.0
CPU Frequency = 20 MHz
Max number PWM channels = 16
TCB Clock Frequency = Full clock (20/16MHz, etc) for highest accuracy
Starting ITimer OK, micros() = 15569
[PWM] Frequency =  1.00
[PWM] Frequency =  2.00
[PWM] Frequency =  3.00
[PWM] Frequency =  4.00
[PWM] Frequency =  5.00
[PWM] Frequency =  6.00
[PWM] Frequency =  7.00
[PWM] Frequency =  8.00
SimpleTimer (us): 2000, us : 7889400, Dus : 7868891
PWM Channel : 0, prog Period (ms): 1000.00, actual : 1000065, prog DutyCycle : 5, actual : 5.00
PWM Channel : 1, prog Period (ms): 500.00, actual : 500018, prog DutyCycle : 10, actual : 9.99
PWM Channel : 2, prog Period (ms): 333.33, actual : 333369, prog DutyCycle : 20, actual : 19.99
PWM Channel : 3, prog Period (ms): 250.00, actual : 249361, prog DutyCycle : 30, actual : 30.06
PWM Channel : 4, prog Period (ms): 200.00, actual : 199999, prog DutyCycle : 40, actual : 39.97
PWM Channel : 5, prog Period (ms): 166.67, actual : 166717, prog DutyCycle : 45, actual : 44.95
PWM Channel : 6, prog Period (ms): 142.86, actual : 142904, prog DutyCycle : 50, actual : 49.94
PWM Channel : 7, prog Period (ms): 125.00, actual : 125031, prog DutyCycle : 55, actual : 54.95
SimpleTimer (us): 2000, us : 15209668, Dus : 7320268
PWM Channel : 0, prog Period (ms): 1000.00, actual : 1000067, prog DutyCycle : 5, actual : 5.00
PWM Channel : 1, prog Period (ms): 500.00, actual : 500047, prog DutyCycle : 10, actual : 9.99
PWM Channel : 2, prog Period (ms): 333.33, actual : 333331, prog DutyCycle : 20, actual : 19.99
PWM Channel : 3, prog Period (ms): 250.00, actual : 175834, prog DutyCycle : 30, actual : 42.64
PWM Channel : 4, prog Period (ms): 200.00, actual : 200075, prog DutyCycle : 40, actual : 39.96
PWM Channel : 5, prog Period (ms): 166.67, actual : 166723, prog DutyCycle : 45, actual : 44.97
PWM Channel : 6, prog Period (ms): 142.86, actual : 142909, prog DutyCycle : 50, actual : 49.96
PWM Channel : 7, prog Period (ms): 125.00, actual : 125073, prog DutyCycle : 55, actual : 54.96
SimpleTimer (us): 2000, us : 22983887, Dus : 7774219
PWM Channel : 0, prog Period (ms): 1000.00, actual : 1000031, prog DutyCycle : 5, actual : 5.00
PWM Channel : 1, prog Period (ms): 500.00, actual : 500018, prog DutyCycle : 10, actual : 9.99
PWM Channel : 2, prog Period (ms): 333.33, actual : 333332, prog DutyCycle : 20, actual : 19.99
PWM Channel : 3, prog Period (ms): 250.00, actual : 250023, prog DutyCycle : 30, actual : 29.99
PWM Channel : 4, prog Period (ms): 200.00, actual : 200032, prog DutyCycle : 40, actual : 39.97
PWM Channel : 5, prog Period (ms): 166.67, actual : 166716, prog DutyCycle : 45, actual : 44.95
PWM Channel : 6, prog Period (ms): 142.86, actual : 142865, prog DutyCycle : 50, actual : 49.98
PWM Channel : 7, prog Period (ms): 125.00, actual : 125062, prog DutyCycle : 55, actual : 54.98
...

2. ISR_8_PWMs_Array on AVR_ATtiny3217

The following is the sample terminal output when running example ISR_8_PWMs_Array on AVR_ATtiny3217 to demonstrate how to use multiple PWM channels with simple callback functions.

Starting ISR_8_PWMs_Array on AVR_ATtiny3217
ATtiny_Slow_PWM v1.0.0
CPU Frequency = 20 MHz
Max number PWM channels = 16
TCB Clock Frequency = Full clock (20/16MHz, etc) for highest accuracy
Starting ITimer OK, micros() = 14778
[PWM] Frequency =  1.00
[PWM] Frequency =  2.00
[PWM] Frequency =  3.00
[PWM] Frequency =  4.00
[PWM] Frequency =  5.00
[PWM] Frequency =  6.00
[PWM] Frequency =  7.00
[PWM] Frequency =  8.00

3. ISR_8_PWMs_Array_Simple on AVR_ATtiny3217

The following is the sample terminal output when running example ISR_8_PWMs_Array_Simple on AVR_ATtiny3217 to demonstrate how to use multiple PWM channels.

Starting ISR_8_PWMs_Array_Simple on AVR_ATtiny3217
ATtiny_Slow_PWM v1.0.0
CPU Frequency = 20 MHz
Max number PWM channels = 16
TCB Clock Frequency = Full clock (20/16MHz, etc) for highest accuracy
Starting ITimer OK, micros() = 15609
[PWM] Frequency =  1.00
[PWM] Frequency =  2.00
[PWM] Frequency =  3.00
[PWM] Frequency =  4.00
[PWM] Frequency =  5.00
[PWM] Frequency =  6.00
[PWM] Frequency =  7.00
[PWM] Frequency =  8.00

4. ISR_Modify_PWM on AVR_ATtiny3217

The following is the sample terminal output when running example ISR_Modify_PWM on AVR_ATtiny3217 to demonstrate how to modify PWM settings on-the-fly without deleting the PWM channel

Starting ISR_Modify_PWM on AVR_ATtiny3217
ATtiny_Slow_PWM v1.0.0
CPU Frequency = 20 MHz
Max number PWM channels = 16
TCB Clock Frequency = Full clock (20/16MHz, etc) for highest accuracy
Starting ITimer OK, micros() = 14755
Using PWM Freq = 2.00, PWM DutyCycle = 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00
Modify Freq => 1.00, DC => 5.55
Modify Freq => 2.00, DC => 10.00

5. ISR_Changing_PWM on AVR_ATtiny3217

The following is the sample terminal output when running example ISR_Changing_PWM on AVR_ATtiny3217 to demonstrate how to modify PWM settings on-the-fly by deleting the PWM channel and reinit the PWM channel

Starting ISR_Changing_PWM on AVR_ATtiny3217
ATtiny_Slow_PWM v1.0.0
CPU Frequency = 20 MHz
Max number PWM channels = 16
TCB Clock Frequency = Full clock (20/16MHz, etc) for highest accuracy
Starting ITimer OK, micros() = 14769
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00
PWM Freq = 1.00, DC = 50.00
PWM Freq = 2.00, DC = 90.00

Debug

Debug is enabled by default on Serial.

You can also change the debugging level _PWM_LOGLEVEL_ from 0 to 4

// Don't define _PWM_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system.
#define _PWM_LOGLEVEL_     0

Troubleshooting

If you get compilation errors, more often than not, you may need to install a newer version of the core for Arduino boards.

Sometimes, the library will only work if you update the board core to the latest version because I am using newly added functions.

Issues

Submit issues to: ATtiny_Slow_PWM issues

TO DO

Search for bug and improvement
Add support to AVR ATtiny-based boards (ATtiny3217, etc.) using megaTinyCore

DONE

Basic hardware multi-channel PWM for AVR ATtiny-based boards (ATtiny3217, etc.) using megaTinyCore
Add Table of Contents
Add functions to modify PWM settings on-the-fly
Fix multiple-definitions linker error
Optimize library code by using reference-passing instead of value-passing
Improve accuracy by using float, instead of uint32_t for dutycycle
DutyCycle to be optionally updated at the end current PWM period instead of immediately.
Display informational warning only when _PWM_LOGLEVEL_ > 3
Make MAX_NUMBER_CHANNELS configurable to max 64 PWM channels
Remove debug codes possibly causing hang

Contributions and Thanks

Many thanks for everyone for bug reporting, new feature suggesting, testing and contributing to the development of this library. Especially to these people who have directly or indirectly contributed to this Dx_TimerInterrupt library

Thanks to good work of Spence Konde (aka Dr. Azzy) for the megaTinyCore
Thanks to LaurentR59 to request

the enhancement Support for DX CORE CPU and MightyCORE CPU possible? #8 leading to this new library

_{⭐️⭐️ Spence Konde}

_LaurentR59

Contributing

If you want to contribute to this project:

Report bugs and errors
Ask for enhancements
Create issues and pull requests
Tell other people about this library

License

The library is licensed under MIT

Name		Name	Last commit message	Last commit date
Latest commit History 20 Commits
.github		.github
examples		examples
pics		pics
platformio		platformio
src		src
utils		utils
.codespellrc		.codespellrc
.gitignore		.gitignore
CONTRIBUTING.md		CONTRIBUTING.md
LICENSE		LICENSE
README.md		README.md
changelog.md		changelog.md
keywords.txt		keywords.txt
library.json		library.json
library.properties		library.properties

	// Important Note: To use drag-and-drop into CURIOSITY virtual drive if you can program via Arduino IDE
	// For example, check https://ww1.microchip.com/downloads/en/DeviceDoc/40002193A.pdf

	#if !( defined(MEGATINYCORE) )
	#error This is designed only for MEGATINYCORE megaAVR board! Please check your Tools->Board setting
	#endif

	// These define's must be placed at the beginning before #include "ATtiny_Slow_PWM.h"
	// _PWM_LOGLEVEL_ from 0 to 4
	// Don't define _PWM_LOGLEVEL_ > 0. Only for special ISR debugging only. Can hang the system.
	#define _PWM_LOGLEVEL_ 0

	// Be careful when using MAX_NUMBER_CHANNELS > 16. Max pemissible MAX_NUMBER_CHANNELS is 64
	#define MAX_NUMBER_CHANNELS 16

	// Select USING_FULL_CLOCK == true for 20/16MHz to Timer TCBx => shorter timer, but better accuracy
	// Select USING_HALF_CLOCK == true for 10/ 8MHz to Timer TCBx => shorter timer, but better accuracy
	// Select USING_250KHZ == true for 250KHz to Timer TCBx => longer timer, but worse accuracy
	// Not select for default 250KHz to Timer TCBx => longer timer, but worse accuracy
	#define USING_FULL_CLOCK true
	#define USING_HALF_CLOCK false
	#define USING_250KHZ false // Not supported now

	// Try to use RTC, TCA0 or TCD0 for millis()
	#define USE_TIMER_0 true // Check if used by millis(), Servo or tone()
	#define USE_TIMER_1 false // Check if used by millis(), Servo or tone()

	#if USE_TIMER_0
	#define CurrentTimer ITimer0
	#elif USE_TIMER_1
	#define CurrentTimer ITimer1
	#else
	#error You must select one Timer
	#endif

	#define USING_MICROS_RESOLUTION true //false

	// To be included only in main(), .ino with setup() to avoid `Multiple Definitions` Linker Error
	#include "ATtiny_Slow_PWM.h"

	#include <SimpleTimer.h> // https://github.com/jfturcot/SimpleTimer

	#define LED_OFF HIGH
	#define LED_ON LOW

	#ifdef LED_BUILTIN
	#undef LED_BUILTIN

	// To modify according to your board
	// For Curiosity Nano ATtiny3217 => PIN_PA3
	#if defined(ARDUINO_AVR_CuriosityNano3217)
	#define LED_BUILTIN PIN_PA3
	#else
	// standard Arduino pin 13
	#define LED_BUILTIN PIN_PA3
	#endif
	#endif

	#define USING_HW_TIMER_INTERVAL_MS false //true

	// Don't change these numbers to make higher Timer freq. System can hang
	#define HW_TIMER_INTERVAL_MS 0.0333f
	#define HW_TIMER_INTERVAL_FREQ 30000L

	volatile uint32_t startMicros = 0;

	// Init AT_TINY_SLOW_PWM, each can service max 64 different ISR-based PWM channels
	AT_TINY_SLOW_PWM_ISR ISR_PWM;

	//////////////////////////////////////////////////////

	void TimerHandler()
	{
	ISR_PWM.run();
	}

	/////////////////////////////////////////////////

	#define PIN_D0 0
	#define PIN_D1 1
	#define PIN_D2 2
	#define PIN_D3 3
	#define PIN_D4 4
	#define PIN_D5 5
	#define PIN_D6 6

	// You can assign pins here. Be careful to select good pin to use or crash, e.g pin 6-11
	uint32_t PWM_Pin[] =
	{
	LED_BUILTIN, PIN_D0, PIN_D1, PIN_D2, PIN_D3, PIN_D4, PIN_D5, PIN_D6
	};

	#define NUMBER_ISR_PWMS ( sizeof(PWM_Pin) / sizeof(uint32_t) )

	typedef void (*irqCallback) ();

	//////////////////////////////////////////////////////

	#define USE_COMPLEX_STRUCT true

	//////////////////////////////////////////////////////

	#if USE_COMPLEX_STRUCT

	typedef struct
	{
	uint32_t PWM_Pin;
	irqCallback irqCallbackStartFunc;
	irqCallback irqCallbackStopFunc;

	uint32_t PWM_Freq;

	uint32_t PWM_DutyCycle;

	uint32_t deltaMicrosStart;
	uint32_t previousMicrosStart;

	uint32_t deltaMicrosStop;
	uint32_t previousMicrosStop;

	} ISR_PWM_Data;

	// In AVRDx, avoid doing something fancy in ISR, for example Serial.print()
	// The pure simple Serial.prints here are just for demonstration and testing. Must be eliminate in working environment
	// Or you can get this run-time error / crash

	void doingSomethingStart(int index);

	void doingSomethingStop(int index);

	#else // #if USE_COMPLEX_STRUCT

	volatile unsigned long deltaMicrosStart [] = { 0, 0, 0, 0, 0, 0, 0, 0 };
	volatile unsigned long previousMicrosStart [] = { 0, 0, 0, 0, 0, 0, 0, 0 };

	volatile unsigned long deltaMicrosStop [] = { 0, 0, 0, 0, 0, 0, 0, 0 };
	volatile unsigned long previousMicrosStop [] = { 0, 0, 0, 0, 0, 0, 0, 0 };


	// You can assign any interval for any timer here, in Microseconds
	uint32_t PWM_Period[] =
	{
	1000L, 500L, 333L, 250L, 200L, 166L, 142L, 125L
	};

	// You can assign any interval for any timer here, in Hz
	float PWM_Freq[] =
	{
	1.0f, 2.0f, 3.0f, 4.0f, 5.0f, 6.0f, 7.0f, 8.0f,
	};

	// You can assign any interval for any timer here, in Microseconds
	float PWM_DutyCycle[] =
	{
	5.0, 10.0, 20.0, 30.0, 40.0, 45.0, 50.0, 55.0
	};

	void doingSomethingStart(int index)
	{
	unsigned long currentMicros = micros();

	deltaMicrosStart[index] = currentMicros - previousMicrosStart[index];
	previousMicrosStart[index] = currentMicros;
	}

	void doingSomethingStop(int index)
	{
	unsigned long currentMicros = micros();

	// Count from start to stop PWM pulse
	deltaMicrosStop[index] = currentMicros - previousMicrosStart[index];
	previousMicrosStop[index] = currentMicros;
	}

	#endif // #if USE_COMPLEX_STRUCT

	////////////////////////////////////
	// Shared
	////////////////////////////////////

	void doingSomethingStart0()
	{
	doingSomethingStart(0);
	}

	void doingSomethingStart1()
	{
	doingSomethingStart(1);
	}

	void doingSomethingStart2()
	{
	doingSomethingStart(2);
	}

	void doingSomethingStart3()
	{
	doingSomethingStart(3);
	}

	void doingSomethingStart4()
	{
	doingSomethingStart(4);
	}

	void doingSomethingStart5()
	{
	doingSomethingStart(5);
	}

	void doingSomethingStart6()
	{
	doingSomethingStart(6);
	}

	void doingSomethingStart7()
	{
	doingSomethingStart(7);
	}


	//////////////////////////////////////////////////////

	void doingSomethingStop0()
	{
	doingSomethingStop(0);
	}

	void doingSomethingStop1()
	{
	doingSomethingStop(1);
	}

	void doingSomethingStop2()
	{
	doingSomethingStop(2);
	}

	void doingSomethingStop3()
	{
	doingSomethingStop(3);
	}

	void doingSomethingStop4()
	{
	doingSomethingStop(4);
	}

	void doingSomethingStop5()
	{
	doingSomethingStop(5);
	}

	void doingSomethingStop6()
	{
	doingSomethingStop(6);
	}

	void doingSomethingStop7()
	{
	doingSomethingStop(7);
	}


	//////////////////////////////////////////////////////

	#if USE_COMPLEX_STRUCT

	ISR_PWM_Data curISR_PWM_Data[] =
	{
	// pin, irqCallbackStartFunc, irqCallbackStopFunc, PWM_Freq, PWM_DutyCycle, deltaMicrosStart, previousMicrosStart, deltaMicrosStop, previousMicrosStop
	{ LED_BUILTIN, doingSomethingStart0, doingSomethingStop0, 1, 5, 0, 0, 0, 0 },
	{ PIN_D0, doingSomethingStart1, doingSomethingStop1, 2, 10, 0, 0, 0, 0 },
	{ PIN_D1, doingSomethingStart2, doingSomethingStop2, 3, 20, 0, 0, 0, 0 },
	{ PIN_D2, doingSomethingStart3, doingSomethingStop3, 4, 30, 0, 0, 0, 0 },
	{ PIN_D3, doingSomethingStart4, doingSomethingStop4, 5, 40, 0, 0, 0, 0 },
	{ PIN_D4, doingSomethingStart5, doingSomethingStop5, 6, 45, 0, 0, 0, 0 },
	{ PIN_D5, doingSomethingStart6, doingSomethingStop6, 7, 50, 0, 0, 0, 0 },
	{ PIN_D6, doingSomethingStart7, doingSomethingStop7, 8, 55, 0, 0, 0, 0 },
	};


	void doingSomethingStart(int index)
	{
	unsigned long currentMicros = micros();

	curISR_PWM_Data[index].deltaMicrosStart = currentMicros - curISR_PWM_Data[index].previousMicrosStart;
	curISR_PWM_Data[index].previousMicrosStart = currentMicros;
	}

	void doingSomethingStop(int index)
	{
	unsigned long currentMicros = micros();

	//curISR_PWM_Data[index].deltaMicrosStop = currentMicros - curISR_PWM_Data[index].previousMicrosStop;
	// Count from start to stop PWM pulse
	curISR_PWM_Data[index].deltaMicrosStop = currentMicros - curISR_PWM_Data[index].previousMicrosStart;
	curISR_PWM_Data[index].previousMicrosStop = currentMicros;
	}

	#else // #if USE_COMPLEX_STRUCT

	irqCallback irqCallbackStartFunc[] =
	{
	doingSomethingStart0, doingSomethingStart1, doingSomethingStart2, doingSomethingStart3,
	doingSomethingStart4, doingSomethingStart5, doingSomethingStart6, doingSomethingStart7
	};

	irqCallback irqCallbackStopFunc[] =
	{
	doingSomethingStop0, doingSomethingStop1, doingSomethingStop2, doingSomethingStop3,
	doingSomethingStop4, doingSomethingStop5, doingSomethingStop6, doingSomethingStop7
	};

	#endif // #if USE_COMPLEX_STRUCT

	//////////////////////////////////////////////////////

	#define SIMPLE_TIMER_MS 2000L

	// Init SimpleTimer
	SimpleTimer simpleTimer;

	// Here is software Timer, you can do somewhat fancy stuffs without many issues.
	// But always avoid
	// 1. Long delay() it just doing nothing and pain-without-gain wasting CPU power.Plan and design your code / strategy ahead
	// 2. Very long "do", "while", "for" loops without predetermined exit time.
	void simpleTimerDoingSomething2s()
	{
	static unsigned long previousMicrosStart = startMicros;

	unsigned long currMicros = micros();

	Serial.print(F("SimpleTimer (us): ")); Serial.print(SIMPLE_TIMER_MS);
	Serial.print(F(", us : ")); Serial.print(currMicros);
	Serial.print(F(", Dus : ")); Serial.println(currMicros - previousMicrosStart);

	for (uint16_t i = 0; i < NUMBER_ISR_PWMS; i++)
	{
	#if USE_COMPLEX_STRUCT
	Serial.print(F("PWM Channel : ")); Serial.print(i);
	Serial.print(F(", prog Period (ms): "));

	Serial.print(1000.f / curISR_PWM_Data[i].PWM_Freq);

	Serial.print(F(", actual : ")); Serial.print((uint32_t) curISR_PWM_Data[i].deltaMicrosStart);

	Serial.print(F(", prog DutyCycle : "));

	Serial.print(curISR_PWM_Data[i].PWM_DutyCycle);

	Serial.print(F(", actual : ")); Serial.println((float) curISR_PWM_Data[i].deltaMicrosStop * 100.0f / curISR_PWM_Data[i].deltaMicrosStart);
	//Serial.print(F(", actual deltaMicrosStop : ")); Serial.println(curISR_PWM_Data[i].deltaMicrosStop);
	//Serial.print(F(", actual deltaMicrosStart : ")); Serial.println(curISR_PWM_Data[i].deltaMicrosStart);

	#else

	Serial.print(F("PWM Channel : ")); Serial.print(i);

	Serial.print(1000 / PWM_Freq[i]);

	Serial.print(F(", prog. Period (us): ")); Serial.print(PWM_Period[i]);
	Serial.print(F(", actual : ")); Serial.print(deltaMicrosStart[i]);

	Serial.print(F(", prog DutyCycle : "));

	Serial.print(PWM_DutyCycle[i]);

	Serial.print(F(", actual : ")); Serial.println( (float) deltaMicrosStop[i] * 100.0f / deltaMicrosStart[i]);
	//Serial.print(F(", actual deltaMicrosStop : ")); Serial.println(deltaMicrosStop[i]);
	//Serial.print(F(", actual deltaMicrosStart : ")); Serial.println(deltaMicrosStart[i]);
	#endif
	}

	previousMicrosStart = currMicros;
	}

	void setup()
	{
	Serial.begin(115200);
	while (!Serial && millis() < 5000);

	Serial.print(F("\nStarting ISR_8_PWMs_Array_Complex on ")); Serial.println(BOARD_NAME);
	Serial.println(AT_TINY_SLOW_PWM_VERSION);
	Serial.print(F("CPU Frequency = ")); Serial.print(F_CPU / 1000000); Serial.println(F(" MHz"));
	Serial.print(F("Max number PWM channels = ")); Serial.println(MAX_NUMBER_CHANNELS);

	Serial.print(F("TCB Clock Frequency = "));

	#if USING_FULL_CLOCK
	Serial.println(F("Full clock (20/16MHz, etc) for highest accuracy"));
	#elif USING_HALF_CLOCK
	Serial.println(F("Half clock (10/8MHz, etc.) for high accuracy"));
	#else
	Serial.println(F("250KHz for lower accuracy but longer time"));
	#endif

	#if USING_HW_TIMER_INTERVAL_MS

	CurrentTimer.init();

	if (CurrentTimer.attachInterruptInterval(HW_TIMER_INTERVAL_MS, TimerHandler))
	{
	Serial.print(F("Starting ITimer OK, micros() = ")); Serial.println(micros());
	}
	else
	Serial.println(F("Can't set ITimer. Select another freq. or timer"));

	#else

	CurrentTimer.init();

	if (CurrentTimer.attachInterrupt(HW_TIMER_INTERVAL_FREQ, TimerHandler))
	{
	Serial.print(F("Starting ITimer OK, micros() = ")); Serial.println(micros());
	}
	else
	Serial.println(F("Can't set ITimer. Select another freq. or timer"));

	#endif // USING_HW_TIMER_INTERVAL_MS

	startMicros = micros();

	// Just to demonstrate, don't use too many ISR Timers if not absolutely necessary
	// You can use up to 16 timer for each ISR_PWM

	for (uint16_t i = 0; i < NUMBER_ISR_PWMS; i++)
	{
	#if USE_COMPLEX_STRUCT
	curISR_PWM_Data[i].previousMicrosStart = startMicros;
	//ISR_PWM.setInterval(curISR_PWM_Data[i].PWM_Period, curISR_PWM_Data[i].irqCallbackStartFunc);

	//void setPWM(uint32_t pin, float frequency, float dutycycle
	// , timer_callback_p StartCallback = nullptr, timer_callback_p StopCallback = nullptr)

	// You can use this with PWM_Freq in Hz
	ISR_PWM.setPWM(curISR_PWM_Data[i].PWM_Pin, curISR_PWM_Data[i].PWM_Freq, curISR_PWM_Data[i].PWM_DutyCycle,
	curISR_PWM_Data[i].irqCallbackStartFunc, curISR_PWM_Data[i].irqCallbackStopFunc);

	#else
	previousMicrosStart[i] = micros();

	// You can use this with PWM_Freq in Hz
	ISR_PWM.setPWM(PWM_Pin[i], PWM_Freq[i], PWM_DutyCycle[i], irqCallbackStartFunc[i], irqCallbackStopFunc[i]);

	#endif
	}

	// You need this timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary.
	simpleTimer.setInterval(SIMPLE_TIMER_MS, simpleTimerDoingSomething2s);
	}

	#define BLOCKING_TIME_MS 10000L

	void loop()
	{
	// This unadvised blocking task is used to demonstrate the blocking effects onto the execution and accuracy to Software timer
	// You see the time elapse of ISR_PWM still accurate, whereas very unaccurate for Software Timer
	// The time elapse for 2000ms software timer now becomes 3000ms (BLOCKING_TIME_MS)
	// While that of ISR_PWM is still prefect.
	delay(BLOCKING_TIME_MS);

	// You need this Software timer for non-critical tasks. Avoid abusing ISR if not absolutely necessary
	// You don't need to and never call ISR_PWM.run() here in the loop(). It's already handled by ISR timer.
	simpleTimer.run();
	}

License

khoih-prog/ATtiny_Slow_PWM

Folders and files

Latest commit

History

Repository files navigation

ATtiny_Slow_PWM Library

Table of Contents

Important Note for Arduino IDE

Why do we need this ATtiny_Slow_PWM library

Features

Why using ISR-based PWM is better

Currently supported Boards

Curiosity Nano ATtiny3217

Important Notes about ISR

Prerequisites

Installation

Use Arduino Library Manager

Manual Install

VS Code & PlatformIO

HOWTO Fix Multiple Definitions Linker Error

More useful Information

1. Documents

2. Timer TCB0-TCB1

TCB0-TCB1, TCA, TCD

TCB0, TCA, TCD

TCB0, TCA, no TCD

Usage

1. Init Hardware Timer

2. Set PWM Frequency, dutycycle, attach irqCallbackStartFunc and irqCallbackStopFunc functions

Examples:

Example ISR_8_PWMs_Array_Complex

Debug Terminal Output Samples

1. ISR_8_PWMs_Array_Complex on AVR_ATtiny3217

2. ISR_8_PWMs_Array on AVR_ATtiny3217

3. ISR_8_PWMs_Array_Simple on AVR_ATtiny3217

4. ISR_Modify_PWM on AVR_ATtiny3217

5. ISR_Changing_PWM on AVR_ATtiny3217

Debug

Troubleshooting

Issues

TO DO

DONE

Contributions and Thanks

Contributing

License

Copyright

About

Topics

Resources

License

Stars

Watchers

Forks

Releases 1

Packages 0

Languages

HOWTO Fix `Multiple Definitions` Linker Error

Packages