Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/k…

…ernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (54 commits)
  Revert "pata_sis: Implement MWDMA for the UDMA 133 capable chips"
  libata: Clarify ata_set_lba_range_entries function
  libata: Report zeroed read after TRIM and max discard size
  pata_hpt3x2n: fix overclocked MWDMA0 timing
  pata_it8213: MWDMA0 is unsupported
  [libata] MWDMA0 is unsupported on PIIX-like PATA controllers
  pata_via: clear UDMA transfer mode bit for PIO and MWDMA
  pata_sis: Power Management fix
  pata_rz1000: Power Management fix
  pata_radisys: fix UDMA handling
  pata_ns87415: Power Management fix
  pata_marvell: fix marvell_pre_reset() documentation
  pata_legacy: add pointers to QDI65x0 documentation
  pata_legacy: fix access to control register for QDI6580
  pata_legacy: fix QDI6580DP support
  pata_it8213: fix it8213_pre_reset() documentation
  pata_it8213: fix wrong MWDMA timings being programmed
  pata_it8213: fix PIO2 underclocking
  pata_it8213: fix wrong PIO timings being programmed
  pata_it8213: fix UDMA handling
  ...

drivers/ata/Kconfig

@@ -3,7 +3,7 @@
 #
 
 menuconfig ATA
-	tristate "Serial ATA (prod) and Parallel ATA (experimental) drivers"
+	tristate "Serial ATA and Parallel ATA drivers"
 	depends on HAS_IOMEM
 	depends on BLOCK
 	depends on !(M32R || M68K) || BROKEN
@@ -374,17 +374,17 @@ config PATA_HPT366
 	  If unsure, say N.
 
 config PATA_HPT37X
-	tristate "HPT 370/370A/371/372/374/302 PATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "HPT 370/370A/371/372/374/302 PATA support"
+	depends on PCI
 	help
 	  This option enables support for the majority of the later HPT
 	  PATA controllers via the new ATA layer.
 
 	  If unsure, say N.
 
 config PATA_HPT3X2N
-	tristate "HPT 372N/302N PATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "HPT 372N/302N PATA support"
+	depends on PCI
 	help
 	  This option enables support for the N variant HPT PATA
 	  controllers via the new ATA layer
@@ -401,7 +401,7 @@ config PATA_HPT3X3
 	  If unsure, say N.
 
 config PATA_HPT3X3_DMA
-	bool "HPT 343/363 DMA support (Experimental)"
+	bool "HPT 343/363 DMA support"
 	depends on PATA_HPT3X3
 	help
 	  This option enables DMA support for the HPT343/363
@@ -510,8 +510,8 @@ config PATA_NETCELL
 	  If unsure, say N.
 
 config PATA_NINJA32
-	tristate "Ninja32/Delkin Cardbus ATA support (Experimental)"
-	depends on PCI && EXPERIMENTAL
+	tristate "Ninja32/Delkin Cardbus ATA support"
+	depends on PCI
 	help
 	  This option enables support for the Ninja32, Delkin and
 	  possibly other brands of Cardbus ATA adapter
@@ -573,6 +573,14 @@ config PATA_PCMCIA
 
 	  If unsure, say N.
 
+config PATA_PDC2027X
+	tristate "Promise PATA 2027x support"
+	depends on PCI
+	help
+	  This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
+
+	  If unsure, say N.
+
 config PATA_PDC_OLD
 	tristate "Older Promise PATA controller support"
 	depends on PCI
@@ -643,14 +651,6 @@ config PATA_SERVERWORKS
 
 	  If unsure, say N.
 
-config PATA_PDC2027X
-	tristate "Promise PATA 2027x support"
-	depends on PCI
-	help
-	  This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
-
-	  If unsure, say N.
-
 config PATA_SIL680
 	tristate "CMD / Silicon Image 680 PATA support"
 	depends on PCI
@@ -667,6 +667,15 @@ config PATA_SIS
 
 	  If unsure, say N.
 
+config PATA_TOSHIBA
+	tristate "Toshiba Piccolo support (Experimental)"
+	depends on PCI && EXPERIMENTAL
+	help
+	  Support for the Toshiba Piccolo controllers. Currently only the
+	  primary channel is supported by this driver.
+
+	  If unsure, say N.
+
 config PATA_VIA
 	tristate "VIA PATA support"
 	depends on PCI

drivers/ata/Makefile

@@ -63,6 +63,7 @@ obj-$(CONFIG_PATA_RZ1000)	+= pata_rz1000.o
 obj-$(CONFIG_PATA_SC1200)	+= pata_sc1200.o
 obj-$(CONFIG_PATA_SERVERWORKS)	+= pata_serverworks.o
 obj-$(CONFIG_PATA_SIL680)	+= pata_sil680.o
+obj-$(CONFIG_PATA_TOSHIBA)	+= pata_piccolo.o
 obj-$(CONFIG_PATA_VIA)		+= pata_via.o
 obj-$(CONFIG_PATA_WINBOND)	+= pata_sl82c105.o
 obj-$(CONFIG_PATA_WINBOND_VLB)	+= pata_winbond.o

drivers/ata/ahci.c

@@ -113,6 +113,7 @@ enum {
 	board_ahci_mcp65	= 6,
 	board_ahci_nopmp	= 7,
 	board_ahci_yesncq	= 8,
+	board_ahci_nosntf	= 9,
 
 	/* global controller registers */
 	HOST_CAP		= 0x00, /* host capabilities */
@@ -235,6 +236,7 @@ enum {
 	AHCI_HFLAG_NO_SUSPEND		= (1 << 10), /* don't suspend */
 	AHCI_HFLAG_SRST_TOUT_IS_OFFLINE	= (1 << 11), /* treat SRST timeout as
 							link offline */
+	AHCI_HFLAG_NO_SNTF		= (1 << 12), /* no sntf */
 
 	/* ap->flags bits */
 
@@ -508,14 +510,22 @@ static const struct ata_port_info ahci_port_info[] = {
 		.udma_mask	= ATA_UDMA6,
 		.port_ops	= &ahci_ops,
 	},
-	/* board_ahci_yesncq */
+	[board_ahci_yesncq] =
 	{
 		AHCI_HFLAGS	(AHCI_HFLAG_YES_NCQ),
 		.flags		= AHCI_FLAG_COMMON,
 		.pio_mask	= ATA_PIO4,
 		.udma_mask	= ATA_UDMA6,
 		.port_ops	= &ahci_ops,
 	},
+	[board_ahci_nosntf] =
+	{
+		AHCI_HFLAGS	(AHCI_HFLAG_NO_SNTF),
+		.flags		= AHCI_FLAG_COMMON,
+		.pio_mask	= ATA_PIO4,
+		.udma_mask	= ATA_UDMA6,
+		.port_ops	= &ahci_ops,
+	},
 };
 
 static const struct pci_device_id ahci_pci_tbl[] = {
@@ -531,7 +541,7 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, 0x2683), board_ahci }, /* ESB2 */
 	{ PCI_VDEVICE(INTEL, 0x27c6), board_ahci }, /* ICH7-M DH */
 	{ PCI_VDEVICE(INTEL, 0x2821), board_ahci }, /* ICH8 */
-	{ PCI_VDEVICE(INTEL, 0x2822), board_ahci }, /* ICH8 */
+	{ PCI_VDEVICE(INTEL, 0x2822), board_ahci_nosntf }, /* ICH8 */
 	{ PCI_VDEVICE(INTEL, 0x2824), board_ahci }, /* ICH8 */
 	{ PCI_VDEVICE(INTEL, 0x2829), board_ahci }, /* ICH8M */
 	{ PCI_VDEVICE(INTEL, 0x282a), board_ahci }, /* ICH8M */
@@ -849,6 +859,12 @@ static void ahci_save_initial_config(struct pci_dev *pdev,
 		cap &= ~HOST_CAP_PMP;
 	}
 
+	if ((cap & HOST_CAP_SNTF) && (hpriv->flags & AHCI_HFLAG_NO_SNTF)) {
+		dev_printk(KERN_INFO, &pdev->dev,
+			   "controller can't do SNTF, turning off CAP_SNTF\n");
+		cap &= ~HOST_CAP_SNTF;
+	}
+
 	if (pdev->vendor == PCI_VENDOR_ID_JMICRON && pdev->device == 0x2361 &&
 	    port_map != 1) {
 		dev_printk(KERN_INFO, &pdev->dev,
@@ -2988,6 +3004,14 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 	if (pdev->vendor == PCI_VENDOR_ID_MARVELL && !marvell_enable)
 		return -ENODEV;
 
+	/* Promise's PDC42819 is a SAS/SATA controller that has an AHCI mode.
+	 * At the moment, we can only use the AHCI mode. Let the users know
+	 * that for SAS drives they're out of luck.
+	 */
+	if (pdev->vendor == PCI_VENDOR_ID_PROMISE)
+		dev_printk(KERN_INFO, &pdev->dev, "PDC42819 "
+			   "can only drive SATA devices with this driver\n");
+
 	/* acquire resources */
 	rc = pcim_enable_device(pdev);
 	if (rc)

drivers/ata/ata_generic.c

@@ -168,9 +168,12 @@ static struct pci_device_id ata_generic[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_VIA,    PCI_DEVICE_ID_VIA_82C561), },
 	{ PCI_DEVICE(PCI_VENDOR_ID_OPTI,   PCI_DEVICE_ID_OPTI_82C558), },
 	{ PCI_DEVICE(PCI_VENDOR_ID_CENATEK,PCI_DEVICE_ID_CENATEK_IDE), },
-	{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO), },
+#if !defined(CONFIG_PATA_TOSHIBA) && !defined(CONFIG_PATA_TOSHIBA_MODULE)
 	{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1), },
 	{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2),  },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_3),  },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_5),  },
+#endif	
 	/* Must come last. If you add entries adjust this table appropriately */
 	{ PCI_ANY_ID,		PCI_ANY_ID,			   PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 1},
 	{ 0, },

drivers/ata/ata_piix.c

@@ -869,10 +869,10 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in
 				(timings[pio][1] << 8);
 		}
 
-		if (ap->udma_mask) {
+		if (ap->udma_mask)
 			udma_enable &= ~(1 << devid);
-			pci_write_config_word(dev, master_port, master_data);
-		}
+
+		pci_write_config_word(dev, master_port, master_data);
 	}
 	/* Don't scribble on 0x48 if the controller does not support UDMA */
 	if (ap->udma_mask)

drivers/ata/libata-acpi.c

@@ -807,12 +807,11 @@ static int ata_acpi_exec_tfs(struct ata_device *dev, int *nr_executed)
  * EH context.
  *
  * RETURNS:
- * 0 on success, -errno on failure.
+ * 0 on success, -ENOENT if _SDD doesn't exist, -errno on failure.
  */
 static int ata_acpi_push_id(struct ata_device *dev)
 {
 	struct ata_port *ap = dev->link->ap;
-	int err;
 	acpi_status status;
 	struct acpi_object_list input;
 	union acpi_object in_params[1];
@@ -835,12 +834,16 @@ static int ata_acpi_push_id(struct ata_device *dev)
 	status = acpi_evaluate_object(dev->acpi_handle, "_SDD", &input, NULL);
 	swap_buf_le16(dev->id, ATA_ID_WORDS);
 
-	err = ACPI_FAILURE(status) ? -EIO : 0;
-	if (err < 0)
+	if (status == AE_NOT_FOUND)
+		return -ENOENT;
+
+	if (ACPI_FAILURE(status)) {
 		ata_dev_printk(dev, KERN_WARNING,
 			       "ACPI _SDD failed (AE 0x%x)\n", status);
+		return -EIO;
+	}
 
-	return err;
+	return 0;
 }
 
 /**
@@ -971,7 +974,7 @@ int ata_acpi_on_devcfg(struct ata_device *dev)
 	/* do _SDD if SATA */
 	if (acpi_sata) {
 		rc = ata_acpi_push_id(dev);
-		if (rc)
+		if (rc && rc != -ENOENT)
 			goto acpi_err;
 	}
 

drivers/ata/libata-core.c

@@ -6616,6 +6616,13 @@ static int __init ata_init(void)
 {
 	ata_parse_force_param();
 
+	/*
+	 * FIXME: In UP case, there is only one workqueue thread and if you
+	 * have more than one PIO device, latency is bloody awful, with
+	 * occasional multi-second "hiccups" as one PIO device waits for
+	 * another.  It's an ugly wart that users DO occasionally complain
+	 * about; luckily most users have at most one PIO polled device.
+	 */
 	ata_wq = create_workqueue("ata");
 	if (!ata_wq)
 		goto free_force_tbl;

drivers/ata/libata-eh.c

@@ -110,6 +110,13 @@ static const unsigned long ata_eh_identify_timeouts[] = {
 	ULONG_MAX,
 };
 
+static const unsigned long ata_eh_flush_timeouts[] = {
+	15000,	/* be generous with flush */
+	15000,  /* ditto */
+	30000,	/* and even more generous */
+	ULONG_MAX,
+};
+
 static const unsigned long ata_eh_other_timeouts[] = {
 	 5000,	/* same rationale as identify timeout */
 	10000,	/* ditto */
@@ -147,6 +154,8 @@ ata_eh_cmd_timeout_table[ATA_EH_CMD_TIMEOUT_TABLE_SIZE] = {
 	  .timeouts = ata_eh_other_timeouts, },
 	{ .commands = CMDS(ATA_CMD_INIT_DEV_PARAMS),
 	  .timeouts = ata_eh_other_timeouts, },
+	{ .commands = CMDS(ATA_CMD_FLUSH, ATA_CMD_FLUSH_EXT),
+	  .timeouts = ata_eh_flush_timeouts },
 };
 #undef CMDS
 
@@ -3112,6 +3121,82 @@ static int atapi_eh_clear_ua(struct ata_device *dev)
 	return 0;
 }
 
+/**
+ *	ata_eh_maybe_retry_flush - Retry FLUSH if necessary
+ *	@dev: ATA device which may need FLUSH retry
+ *
+ *	If @dev failed FLUSH, it needs to be reported upper layer
+ *	immediately as it means that @dev failed to remap and already
+ *	lost at least a sector and further FLUSH retrials won't make
+ *	any difference to the lost sector.  However, if FLUSH failed
+ *	for other reasons, for example transmission error, FLUSH needs
+ *	to be retried.
+ *
+ *	This function determines whether FLUSH failure retry is
+ *	necessary and performs it if so.
+ *
+ *	RETURNS:
+ *	0 if EH can continue, -errno if EH needs to be repeated.
+ */
+static int ata_eh_maybe_retry_flush(struct ata_device *dev)
+{
+	struct ata_link *link = dev->link;
+	struct ata_port *ap = link->ap;
+	struct ata_queued_cmd *qc;
+	struct ata_taskfile tf;
+	unsigned int err_mask;
+	int rc = 0;
+
+	/* did flush fail for this device? */
+	if (!ata_tag_valid(link->active_tag))
+		return 0;
+
+	qc = __ata_qc_from_tag(ap, link->active_tag);
+	if (qc->dev != dev || (qc->tf.command != ATA_CMD_FLUSH_EXT &&
+			       qc->tf.command != ATA_CMD_FLUSH))
+		return 0;
+
+	/* if the device failed it, it should be reported to upper layers */
+	if (qc->err_mask & AC_ERR_DEV)
+		return 0;
+
+	/* flush failed for some other reason, give it another shot */
+	ata_tf_init(dev, &tf);
+
+	tf.command = qc->tf.command;
+	tf.flags |= ATA_TFLAG_DEVICE;
+	tf.protocol = ATA_PROT_NODATA;
+
+	ata_dev_printk(dev, KERN_WARNING, "retrying FLUSH 0x%x Emask 0x%x\n",
+		       tf.command, qc->err_mask);
+
+	err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
+	if (!err_mask) {
+		/*
+		 * FLUSH is complete but there's no way to
+		 * successfully complete a failed command from EH.
+		 * Making sure retry is allowed at least once and
+		 * retrying it should do the trick - whatever was in
+		 * the cache is already on the platter and this won't
+		 * cause infinite loop.
+		 */
+		qc->scsicmd->allowed = max(qc->scsicmd->allowed, 1);
+	} else {
+		ata_dev_printk(dev, KERN_WARNING, "FLUSH failed Emask 0x%x\n",
+			       err_mask);
+		rc = -EIO;
+
+		/* if device failed it, report it to upper layers */
+		if (err_mask & AC_ERR_DEV) {
+			qc->err_mask |= AC_ERR_DEV;
+			qc->result_tf = tf;
+			if (!(ap->pflags & ATA_PFLAG_FROZEN))
+				rc = 0;
+		}
+	}
+	return rc;
+}
+
 static int ata_link_nr_enabled(struct ata_link *link)
 {
 	struct ata_device *dev;
@@ -3455,6 +3540,15 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
 			}
 		}
 
+		/* retry flush if necessary */
+		ata_for_each_dev(dev, link, ALL) {
+			if (dev->class != ATA_DEV_ATA)
+				continue;
+			rc = ata_eh_maybe_retry_flush(dev);
+			if (rc)
+				goto dev_fail;
+		}
+
 		/* configure link power saving */
 		if (ehc->i.action & ATA_EH_LPM)
 			ata_for_each_dev(dev, link, ALL)