Configure a Linux VPN client using the command line.
You need the following:
- VPN Server Address
- Pre Shared Key
- Username
- Password
Install the following packages:
sudo apt-get update
sudo apt-get -y install strongswan xl2tpd
yum -y install epel-release
yum --enablerepo=epel -y install strongswan xl2tpd
yum -y install strongswan xl2tpd
Edit ipsec.conf:
sudo nano /etc/ipsec.conf
Replace the file content with the following (replace n.n.n.n with your VPN Server Address):
config setup
conn %default
ikelifetime=60m
keylife=20m
rekeymargin=3m
keyingtries=1
keyexchange=ikev1
authby=secret
ike=aes128-sha1-modp1024,3des-sha1-modp1024!
esp=aes128-sha1-modp1024,3des-sha1-modp1024!
conn L2TP-PSK
keyexchange=ikev1
left=%defaultroute
auto=add
authby=secret
type=transport
leftprotoport=17/1701
rightprotoport=17/1701
# set this to the ip address of your vpn server
right=n.n.n.n
Edit ipsec.secrets:
sudo nano /etc/ipsec.secrets
Replace the file content with the following (replace your_pre_shared_key with your PSK value):
: PSK "your_pre_shared_key"
Additionaly, run the following only if you are using CentOS/RHEL or Fedora:
mv /etc/strongswan/ipsec.conf /etc/strongswan/ipsec.conf.old 2>/dev/null
mv /etc/strongswan/ipsec.secrets /etc/strongswan/ipsec.secrets.old 2>/dev/null
ln -s /etc/ipsec.conf /etc/strongswan/ipsec.conf
ln -s /etc/ipsec.secrets /etc/strongswan/ipsec.secrets
Edit xl2tpd.conf:
sudo nano /etc/xl2tpd/xl2tpd.conf
Append the following to the file (replace n.n.n.n with your VPN Server Address):
[lac myVPN]
; set this to the ip address of your vpn server
lns = n.n.n.n
ppp debug = yes
pppoptfile = /etc/ppp/options.l2tpd.client
length bit = yes
Edit /etc/ppp/options.l2tpd.client:
sudo nano /etc/ppp/options.l2tpd.client
Replace the file content with the following (replace your_user_name and your_password with your VPN credentials):
ipcp-accept-local
ipcp-accept-remote
refuse-eap
require-mschap-v2
noccp
noauth
logfile /var/log/xl2tpd.log
idle 1800
mtu 1410
mru 1410
defaultroute
usepeerdns
debug
connect-delay 5000
name your_user_name
password your_password
Run the following command each time you want to start the ipsec and l2tp connection:
sudo mkdir -p /var/run/xl2tpd
sudo touch /var/run/xl2tpd/l2tp-control
sudo service strongswan restart
sudo service xl2tpd restart
sudo service ipsec restart
sleep 8
sudo ipsec up L2TP-PSK
sleep 8
sudo bash -c 'echo "c myVPN" > /var/run/xl2tpd/l2tp-control'
sleep 8
ifconfig
sudo mkdir -p /var/run/xl2tpd
sudo touch /var/run/xl2tpd/l2tp-control
sudo service strongswan restart
sudo service xl2tpd restart
sleep 8
sudo strongswan up L2TP-PSK
sleep 8
sudo bash -c 'echo "c myVPN" > /var/run/xl2tpd/l2tp-control'
sleep 8
ifconfig
Check the output. You should now see a new interface ppp0. Interface ppp0 is needed to continue to the next step.
Routing traffic to an IP address in your internal network. Replace x.x.x.x with the addres you wish to communicate with through the tunnel device:
sudo ip route add x.x.x.x via $(ip address show dev ppp0 | grep -Po '(?<=peer )(\b([0-9]{1,3}\.){3}[0-9]{1,3}\b)') dev ppp0
If you did run the route command on an EC2 instance and got the error "unable to resolve host <ip-x-x-x-x>: Resource temporarily unavailable", do the following and then rerun the commands from the Connect and Router sections.
Copy the hostname, from the error message, which will contain the private IP address in the form ip-x-x-x-x. For instance ip-172-31-26-197
Open the hosts file
sudo nano /etc/hosts
Add a new entry within the hosts file to include the hostname:
172.31.29.26 ip-172-31-29-26
The VPN connection is now complete. Verify that your traffic is being routed properly. Repalce x.x.x.x with the addres you wish to communicate with through the tunnel device:
ping x.x.x.x
To disconnect run the following:
sudo bash -c 'echo "d myVPN" > /var/run/xl2tpd/l2tp-control'
ipsec down L2TP-PSK
sudo bash -c 'echo "d myVPN" > /var/run/xl2tpd/l2tp-control'
sudo strongswan down L2TP-PSK
Check the logs:
dmesg | less /var/log/xl2tpd.log