-
Notifications
You must be signed in to change notification settings - Fork 11
/
my_machine.h
97 lines (84 loc) · 4.49 KB
/
my_machine.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
/*
my_machine.h - configuration for Atmel SAM3X8E ARM processor
Part of grblHAL
Copyright (c) 2020-2024 Terje Io
grblHAL is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
grblHAL is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with grblHAL. If not, see <http://www.gnu.org/licenses/>.
*/
// NOTE: Only one board may be enabled!
// If none is enabled pin mappings from generic_map.h will be used
// NOTE: Only one board may be enabled!
//#define BOARD_TINYG2_DUE
//#define BOARD_RAMPS_16
//#define BOARD_RAMPS_SMART
//#define BOARD_MEGA256
//#define BOARD_PROTONEER
//#define BOARD_CMCGRATH
//#define BOARD_RADDS_16 // NOTE: untested!!
//#define BOARD_MY_MACHINE // Add my_machine_map.h before enabling this!
// Configuration
// Uncomment to enable.
//#define USB_SERIAL_CDC 1 // Use native USB port for communication.
//#define BLUETOOTH_ENABLE 2 // Set to 2 for HC-05 module. Requires and claims one auxillary input pin.
// Spindle selection:
// Up to four specific spindle drivers can be instantiated at a time
// depending on N_SPINDLE and N_SYS_SPINDLE definitions in grbl/config.h.
// If none are specified the default PWM spindle is instantiated.
// Spindle definitions can be found in grbl/spindle_control.h.
// More here https://github.com/grblHAL/Plugins_spindle
//#define SPINDLE0_ENABLE SPINDLE_HUANYANG1
//#define SPINDLE1_ENABLE SPINDLE_PWM0
//#define SPINDLE2_ENABLE SPINDLE_NONE
//#define SPINDLE2_ENABLE SPINDLE_NONE
// **********************
//#define MODBUS_ENABLE 1 // Set to 1 for auto direction, 2 for direction signal on auxillary output pin.
//#define PLASMA_ENABLE 1 // Plasma/THC plugin.
//#define OPENPNP_ENABLE 1 // OpenPNP plugin. To be completed.
//#define MPG_ENABLE 1 // Enable MPG interface. Requires a serial stream and means to switch between normal and MPG mode.
// 1: Mode switching is by handshake pin.
// 2: Mode switching is by the CMD_MPG_MODE_TOGGLE (0x8B) command character.
//#define KEYPAD_ENABLE 1 // 1: uses a I2C keypad for input.
// 2: uses a serial stream for input. If MPG_ENABLE is set > 0 the serial stream is shared with the MPG.
//#define LASER_COOLANT_ENABLE 1 // Laser coolant plugin. To be completed.
//#define LB_CLUSTERS_ENABLE 1 // LaserBurn cluster support.
//#define EEPROM_ENABLE 16 // I2C EEPROM/FRAM support. Set to 16 for 2K, 32 for 4K, 64 for 8K, 128 for 16K and 256 for 16K capacity.
//#define EEPROM_IS_FRAM 1 // Uncomment when EEPROM is enabled and chip is FRAM, this to remove write delay.
//#define MCP3221_ENABLE 0x4D // Enable MCP3221 I2C ADC input with address 0x4D (0b01001101).
// Optional control signals:
// These will be assigned to aux input pins. Use the $pins command to check which pins are assigned.
// NOTE: If not enough pins are available assignment will silently fail.
//#define PROBE_ENABLE 0 // Default enabled, remove comment to disable probe input.
//#define SAFETY_DOOR_ENABLE 1
//#define MOTOR_FAULT_ENABLE 1
//#define MOTOR_WARNING_ENABLE 1
//#define PROBE_DISCONNECT_ENABLE 1
//#define STOP_DISABLE_ENABLE 1
//#define BLOCK_DELETE_ENABLE 1
//#define SINGLE_BLOCK_ENABLE 1
//#define LIMITS_OVERRIDE_ENABLE 1
#ifndef USB_SERIAL_CDC
#define SERIAL_DEVICE -1 // Select serial device for output if not using native USB, default is -1, max value is 2
#endif
// If the selected board map supports more than three motors ganging and/or auto-squaring
// of axes can be enabled here.
//#define X_GANGED 1
//#define X_AUTO_SQUARE 1
//#define Y_GANGED 1
//#define Y_AUTO_SQUARE 1
//#define Z_GANGED 1
//#define Z_AUTO_SQUARE 1
// For ganged axes the limit switch input (if available) can be configured to act as a max travel limit switch.
// NOTE: If board map already has max limit inputs defined this configuration will be ignored.
//#define X_GANGED_LIM_MAX 1
//#define Y_GANGED_LIM_MAX 1
//#define Z_GANGED_LIM_MAX 1
//
/**/