diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index ae8c40b7db33..2f32d5af76de 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -578,7 +578,7 @@
  * Note: For Bowden Extruders make this large enough to allow load/unload.
  */
 #define PREVENT_LENGTHY_EXTRUDE
-#define EXTRUDE_MAXLENGTH 650 //@ maybe needed for filament loading
+#define EXTRUDE_MAXLENGTH 710 //@ maybe needed for filament loading
 
 //===========================================================================
 //======================== Thermal Runaway Protection =======================
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 582e60c1f5de..55eaf2d4ec34 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1498,7 +1498,7 @@
  *
  * Override the default value based on the driver type set in Configuration.h.
  */
-//#define MINIMUM_STEPPER_PULSE 2
+#define MINIMUM_STEPPER_PULSE 2
 
 /**
  * Maximum stepping rate (in Hz) the stepper driver allows
@@ -1688,7 +1688,7 @@
   #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
   //#define FILAMENT_CHANGE_UNLOAD_LENGTH      650
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      0    // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH      710  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.
@@ -1698,7 +1698,7 @@
   #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE   6  // (mm/s) Load filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
   //#define FILAMENT_CHANGE_FAST_LOAD_LENGTH   615
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH     0  // (mm) Load length of filament, from extruder gear to nozzle.
+  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH    710  // (mm) Load length of filament, from extruder gear to nozzle.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
   #define ADVANCED_PAUSE_CONTINUOUS_PURGE         // Purge continuously up to the purge length until interrupted.
@@ -1720,7 +1720,7 @@
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
   #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // Ensure homing has been completed prior to parking for filament change
+  #define HOME_BEFORE_FILAMENT_CHANGE           // Ensure homing has been completed prior to parking for filament change
 
   // makes more sense
   #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
@@ -2751,8 +2751,8 @@
  */
 //#define WIFISUPPORT
 #if ENABLED(WIFISUPPORT)
-  #define WIFI_SSID "Wifi SSID"
-  #define WIFI_PWD  "Wifi Password"
+  #define WIFI_SSID "MarlinGhost"
+  #define WIFI_PWD  "marlino"
   //#define WEBSUPPORT        // Start a webserver with auto-discovery
   //#define OTASUPPORT        // Support over-the-air firmware updates
 #endif