SW_DevRPiTTY

Device Module "RPiTTY"

Module Information

System

System	Comments
RPi	All boards with Raspian
PC Linux	n/a
PC Windows	n/a
Mac	n/a

Dependencies

Python Module	Install	Anaconda
pigpio	pip install pigpio	conda install pigpio

Command Line Arguments

-G
--RPiTTY

Config File Parameter

Parameter	Default	Type/Range	Description
mode	"TW39"	"TW39" / "V10"	TW39 for all TTY‘s with high voltage current loop; V10 for machines with V.10 interface (mainly TeKaDe FS200 / FS220)
baudrate	50	38 ... 50 … 200	Baud rate
bytesize	5	5 … 8	# of databits
stopbits	1.5	1 / 1.5 / 2	# of stopbits
pin_txd	17	number	GPIO# of TX-Data pin
inv_txd	false	false / true	If true, use inverted signal on TX-Data pin, not possible with PIGPIO
pin_dir	0	number	GPIO# of DIR pin. This pin is set to 1 on transmitting each byte for hardware loopback supression
pin_rxd	27	number	GPIO# of RX-Data pin
inv_rxd	false	false / true	If true, use inverted signal on RX-Data pin
pin_relay	22	number	GPIO# of relay coil pin; in non-FSG mode used to switch the line power of the teletype; in FSG mode, relay is used to alter the polarity of the current loop when a connection is established; see corresponding hardware description
inv_relay	false	false / true	If true, use inverted signal on pin
pin_power	0	number	GPIO# of pin used to switch off current loop
inv_power	false	false / true	If true, use inverted signal on pin
pin_number_switch	6	number	GPIO# of pin connected to the number switch; often wired to pin_rxd. Set to -1 to enable pin_number_switch in module RPiCtrl Set to 0 to select keyboard dialling
inv_number_switch	false	false / true	If true, use inverted signal on pin
use_observe_line	true	false / true	If true, monitor pin_observe_line for state changes of >0,5s
pin_observe_line	[pin_rxd]	number	GPIO# of pin to observe
inv_observe_line	[inv_rxd]	false / true	If true, use inverted signal on pin
coding	0	0,1,2,3	0:ITA2=CCITT2, 1:US, 2:MKT2, 3:ZUSE (see txCode.md)
loopback	true	false / true	if true, sent characters are removed from receive buffer
timing_rxd	false	false / true	?
WB_pulse_length	40	number	set length of WB pulse in milliseconds
double_WR	false	false / true	if true, add an extra <CR> to give the old machines more time to move to the start of the line

Description

This module is used to control TW39/V10 machines connected via the corresponding TW39 or V.10 hardware to the GPIO-interface of a Raspberry Pi running Raspbian OS. It is not suitable for standard computers running Windows, MAC OS or Linux.

The RPi's built in UART cannot cope with 50 baud transmission speed. But, the correct timing can be formed jitter-free with the library “PiGPIO”. Receiving can be handled by asynchronous callbacks implemented in this library. This enables a Linux based computer like the RPi to handle precise and reliable timings.

In TW39 mode, the module can operate together with a CCU (Fernschaltgerät, FSG); in this case, pin_relay drives a relay which alters polarity depending on the connection state (see HW_ILoop).

The module can also be used to connect a teletype with 40mA current loop directly (CAUTION: DO NOT APPLY FULL LINE VOLTAGE TO THE TELETYPE! 24 Volts will be sufficient to feed the coil via regulated current loop, see HW_ILoop. A polarity relay is not applicable in this case; but when operating the machine e.g. as i-Telex-client, pin_relay may be used to drive a relay to switch on mains supply for the teletype on incoming connections and outgoing connections dialled via number switch. This operation mode requires some additional features from RPiCtrl-module, especially pin_number_switch, pin_button_at, pin_button_st and pin_button_lt (see there).

Last but not least, in V.10 mode the module is able to control a directly connected teletype with V.10 interface (mostly TeKaDe FS200/FS220), no FAG200 is needed. For the corresponding interface hardware see HW_V10.

Implementation

TODO