UBI: Unsorted Block Images

UBI (Latin: "where?") manages multiple logical volumes on a single
flash device, specifically supporting NAND flash devices. UBI provides
a flexible partitioning concept which still allows for wear-levelling
across the whole flash device.

In a sense, UBI may be compared to the Logical Volume Manager
(LVM). Whereas LVM maps logical sector numbers to physical HDD sector
numbers, UBI maps logical eraseblocks to physical eraseblocks.

More information may be found at
http://www.linux-mtd.infradead.org/doc/ubi.html

Partitioning/Re-partitioning

  An UBI volume occupies a certain number of erase blocks. This is
  limited by a configured maximum volume size, which could also be
  viewed as the partition size. Each individual UBI volume's size can
  be changed independently of the other UBI volumes, provided that the
  sum of all volume sizes doesn't exceed a certain limit.

  UBI supports dynamic volumes and static volumes. Static volumes are
  read-only and their contents are protected by CRC check sums.

Bad eraseblocks handling

  UBI transparently handles bad eraseblocks. When a physical
  eraseblock becomes bad, it is substituted by a good physical
  eraseblock, and the user does not even notice this.

Scrubbing

  On a NAND flash bit flips can occur on any write operation,
  sometimes also on read. If bit flips persist on the device, at first
  they can still be corrected by ECC, but once they accumulate,
  correction will become impossible. Thus it is best to actively scrub
  the affected eraseblock, by first copying it to a free eraseblock
  and then erasing the original. The UBI layer performs this type of
  scrubbing under the covers, transparently to the UBI volume users.

Erase Counts

  UBI maintains an erase count header per eraseblock. This frees
  higher-level layers (like file systems) from doing this and allows
  for centralized erase count management instead. The erase counts are
  used by the wear-levelling algorithm in the UBI layer. The algorithm
  itself is exchangeable.

Booting from NAND

  For booting directly from NAND flash the hardware must at least be
  capable of fetching and executing a small portion of the NAND
  flash. Some NAND flash controllers have this kind of support. They
  usually limit the window to a few kilobytes in erase block 0. This
  "initial program loader" (IPL) must then contain sufficient logic to
  load and execute the next boot phase.

  Due to bad eraseblocks, which may be randomly scattered over the
  flash device, it is problematic to store the "secondary program
  loader" (SPL) statically. Also, due to bit-flips it may become
  corrupted over time. UBI allows to solve this problem gracefully by
  storing the SPL in a small static UBI volume.

UBI volumes vs. static partitions

  UBI volumes are still very similar to static MTD partitions:

    * both consist of eraseblocks (logical eraseblocks in case of UBI
      volumes, and physical eraseblocks in case of static partitions;
    * both support three basic operations - read, write, erase.

  But UBI volumes have the following advantages over traditional
  static MTD partitions:

    * there are no eraseblock wear-leveling constraints in case of UBI
      volumes, so the user should not care about this;
    * there are no bit-flips and bad eraseblocks in case of UBI volumes.

  So, UBI volumes may be considered as flash devices with relaxed
  restrictions.

Where can it be found?

  Documentation, kernel code and applications can be found in the MTD
  gits.

What are the applications for?

  The applications help to create binary flash images for two purposes: pfi
  files (partial flash images) for in-system update of UBI volumes, and plain
  binary images, with or without OOB data in case of NAND, for a manufacturing
  step. Furthermore some tools are/and will be created that allow flash content
  analysis after a system has crashed..

Who did UBI?

  The original ideas, where UBI is based on, were developed by Andreas
  Arnez, Frank Haverkamp and Thomas Gleixner. Josh W. Boyer and some others
  were involved too. The implementation of the kernel layer was done by Artem
  B. Bityutskiy. The user-space applications and tools were written by Oliver
  Lohmann with contributions from Frank Haverkamp, Andreas Arnez, and Artem.
  Joern Engel contributed a patch which modifies JFFS2 so that it can be run on
  a UBI volume. Thomas Gleixner did modifications to the NAND layer. Alexander
  Schmidt made some testing work as well as core functionality improvements.

Signed-off-by: Artem B. Bityutskiy <dedekind@linutronix.de>
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>

Author: Artem B. Bityutskiy

drivers/mtd/Kconfig

@@ -292,5 +292,7 @@ source "drivers/mtd/nand/Kconfig"
 
 source "drivers/mtd/onenand/Kconfig"
 
+source "drivers/mtd/ubi/Kconfig"
+
 endmenu
 

drivers/mtd/Makefile

@@ -28,3 +28,5 @@ nftl-objs		:= nftlcore.o nftlmount.o
 inftl-objs		:= inftlcore.o inftlmount.o
 
 obj-y		+= chips/ maps/ devices/ nand/ onenand/
+
+obj-$(CONFIG_MTD_UBI)		+= ubi/

drivers/mtd/ubi/Kconfig

@@ -0,0 +1,58 @@
+# drivers/mtd/ubi/Kconfig
+
+menu "UBI - Unsorted block images"
+	depends on MTD
+
+config MTD_UBI
+	tristate "Enable UBI"
+	depends on MTD
+	select CRC32
+	help
+	  UBI is a software layer above MTD layer which admits of LVM-like
+	  logical volumes on top of MTD devices, hides some complexities of
+	  flash chips like wear and bad blocks and provides some other useful
+	  capabilities. Please, consult the MTD web site for more details
+	  (www.linux-mtd.infradead.org).
+
+config MTD_UBI_WL_THRESHOLD
+	int "UBI wear-leveling threshold"
+	default 4096
+	range 2 65536
+	depends on MTD_UBI
+	help
+	  This parameter defines the maximum difference between the highest
+	  erase counter value and the lowest erase counter value of eraseblocks
+	  of UBI devices. When this threshold is exceeded, UBI starts performing
+	  wear leveling by means of moving data from eraseblock with low erase
+	  counter to eraseblocks with high erase counter. Leave the default
+	  value if unsure.
+
+config MTD_UBI_BEB_RESERVE
+	int "Percentage of reserved eraseblocks for bad eraseblocks handling"
+	default 1
+	range 0 25
+	depends on MTD_UBI
+	help
+	  If the MTD device admits of bad eraseblocks (e.g. NAND flash), UBI
+	  reserves some amount of physical eraseblocks to handle new bad
+	  eraseblocks. For example, if a flash physical eraseblock becomes bad,
+	  UBI uses these reserved physical eraseblocks to relocate the bad one.
+	  This option specifies how many physical eraseblocks will be reserved
+	  for bad eraseblock handling (percents of total number of good flash
+	  eraseblocks). If the underlying flash does not admit of bad
+	  eraseblocks (e.g. NOR flash), this value is ignored and nothing is
+	  reserved. Leave the default value if unsure.
+
+config MTD_UBI_GLUEBI
+	bool "Emulate MTD devices"
+	default n
+	depends on MTD_UBI
+	help
+	   This option enables MTD devices emulation on top of UBI volumes: for
+	   each UBI volumes an MTD device is created, and all I/O to this MTD
+	   device is redirected to the UBI volume. This is handy to make
+	   MTD-oriented software (like JFFS2) work on top of UBI. Do not enable
+	   this if no legacy software will be used.
+
+source "drivers/mtd/ubi/Kconfig.debug"
+endmenu

drivers/mtd/ubi/Kconfig.debug

@@ -0,0 +1,104 @@
+comment "UBI debugging options"
+	depends on MTD_UBI
+
+config MTD_UBI_DEBUG
+	bool "UBI debugging"
+	depends on SYSFS
+	depends on MTD_UBI
+	select DEBUG_FS
+	select KALLSYMS_ALL
+	help
+	  This option enables UBI debugging.
+
+config MTD_UBI_DEBUG_MSG
+	bool "UBI debugging messages"
+	depends on MTD_UBI_DEBUG
+	default n
+	help
+	  This option enables UBI debugging messages.
+
+config MTD_UBI_DEBUG_PARANOID
+	bool "Extra self-checks"
+	default n
+	depends on MTD_UBI_DEBUG
+	help
+	  This option enables extra checks in UBI code. Note this slows UBI down
+	  significantly.
+
+config MTD_UBI_DEBUG_DISABLE_BGT
+	bool "Do not enable the UBI background thread"
+	depends on MTD_UBI_DEBUG
+	default n
+	help
+	  This option switches the background thread off by default. The thread
+	  may be also be enabled/disabled via UBI sysfs.
+
+config MTD_UBI_DEBUG_USERSPACE_IO
+	bool "Direct user-space write/erase support"
+	default n
+	depends on MTD_UBI_DEBUG
+	help
+	  By default, users cannot directly write and erase individual
+	  eraseblocks of dynamic volumes, and have to use update operation
+	  instead. This option enables this capability - it is very useful for
+	  debugging and testing.
+
+config MTD_UBI_DEBUG_EMULATE_BITFLIPS
+	bool "Emulate flash bit-flips"
+	depends on MTD_UBI_DEBUG
+	default n
+	help
+	  This option emulates bit-flips with probability 1/50, which in turn
+	  causes scrubbing. Useful for debugging and stressing UBI.
+
+config MTD_UBI_DEBUG_EMULATE_WRITE_FAILURES
+	bool "Emulate flash write failures"
+	depends on MTD_UBI_DEBUG
+	default n
+	help
+	  This option emulates write failures with probability 1/100. Useful for
+	  debugging and testing how UBI handlines errors.
+
+config MTD_UBI_DEBUG_EMULATE_ERASE_FAILURES
+	bool "Emulate flash erase failures"
+	depends on MTD_UBI_DEBUG
+	default n
+	help
+	  This option emulates erase failures with probability 1/100. Useful for
+	  debugging and testing how UBI handlines errors.
+
+menu "Additional UBI debugging messages"
+	depends on MTD_UBI_DEBUG
+
+config MTD_UBI_DEBUG_MSG_BLD
+	bool "Additional UBI initialization and build messages"
+	default n
+	depends on MTD_UBI_DEBUG
+	help
+	  This option enables detailed UBI initialization and device build
+	  debugging messages.
+
+config MTD_UBI_DEBUG_MSG_EBA
+	bool "Eraseblock association unit messages"
+	default n
+	depends on MTD_UBI_DEBUG
+	help
+	  This option enables debugging messages from the UBI eraseblock
+	  association unit.
+
+config MTD_UBI_DEBUG_MSG_WL
+	bool "Wear-leveling unit messages"
+	default n
+	depends on MTD_UBI_DEBUG
+	help
+	  This option enables debugging messages from the UBI wear-leveling
+	  unit.
+
+config MTD_UBI_DEBUG_MSG_IO
+	bool "Input/output unit messages"
+	default n
+	depends on MTD_UBI_DEBUG
+	help
+	  This option enables debugging messages from the UBI input/output unit.
+
+endmenu # UBI debugging messages

drivers/mtd/ubi/Makefile

@@ -0,0 +1,7 @@
+obj-$(CONFIG_MTD_UBI) += ubi.o
+
+ubi-y += vtbl.o vmt.o upd.o build.o cdev.o kapi.o eba.o io.o wl.o scan.o
+ubi-y += misc.o
+
+ubi-$(CONFIG_MTD_UBI_DEBUG) += debug.o
+ubi-$(CONFIG_MTD_UBI_GLUEBI) += gluebi.o