V4.12 rc3 r5log rebase #4

liubogithub · 2017-08-03T17:32:00Z

Only for github pull request progress testing! The patch set is for review, not ready for merging.

This introduces add_dev_v2 ioctl to add a device as raid56 journal device. With the help of a journal device, raid56 is able to to get rid of potential write holes. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

The journal device (aka raid56 log) is not for chunk allocation, lets skip it. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

We've put the flag BTRFS_DEV_RAID56_LOG in device->type, so we can recognize the journal device of raid56 while reading the chunk tree. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

This is adding the ability to use a disk as raid5/6's stripe log (aka journal), the primary goal is to fix write hole issue that is inherent in raid56 setup. In a typical raid5/6 setup, both full stripe write and a partial stripe write will generate parity at the very end of writing, so after parity is generated, it's the right time to issue writes. Now with raid5/6's stripe log, every write will be put into the stripe log prior to being written to raid5/6 array, so that we have everything to rewrite all 'not-yet-on-disk' data/parity if a power loss happens while writing data/parity to different disks in raid5/6 array. A metadata block is used here to manage the information of data and parity and it's placed ahead of data and parity on stripe log. Right now such metadata block is limited to one page size and the structure is defined as {metadata block} + {a few payloads} - 'metadata block' contains a magic code, a sequence number and the start position on the stripe log. - 'payload' contains the information about data and parity, e.g. the physical offset and device id where data/parity is supposed to be. Each data block has a payload while each set of parity has a payload (e.g. for raid6, parity p and q has their own payload respectively). And we treat data and parity differently because btrfs always prepares the whole stripe length(64k) of parity, but data may only come from a partial stripe write. This metadata block is written to the raid5/6 stripe log with data/parity in a single bio(could be two bios, doesn't support more than two bios). Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

The log space is limited, so reclaim is necessary when there is not enough space to use. By recording the largest position we've written to the log disk and flushing all disks' cache and the superblock, we can be sure that data and parity before this position have the identical copy in the log and raid5/6 array. Also we need to take care of the case when IOs get reordered. A list is used to keep the order right. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

A raid5/6 log can be loaded while mounting a btrfs (which already has a disk set up as raid5/6 log) or setting up a disk as raid5/6 log for the first time. It gets %journal_tail from super_block where it can read the first 4K block and goes through the sanity checks, if it's valid, then go check if anything needs to be replayed, otherwise it creates a new empty block at the beginning of the disk and new writes will append to it. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

This is adding recovery on raid5/6 log. We've set a %journal_tail in super_block, which indicates the position from where we need to replay data. So we scan the log and replay valid meta/data/parity pairs until finding an invalid one. By replaying, it simply reads data/parity from the raid5/6 log and issues writes to the raid disks where it should be. Please note that the whole meta/data/parity pair can be discarded if it fails the sanity check in the meta block. After recovery, we also append an empty meta block and update the %journal_tail in super_block in order to avoid a situation, where the layout on the raid5/6 log is [valid A][invalid B][valid C], so block A is the only one we should replay. Then the recovery ends up pointing to block A as block B is invalid, and some new writes come in and append to block A so that block B is now overwritten to be a valid meta/data/parity. If a power loss happens, the new recovery starts again from block A, and since block B is now valid, it may replay block C as well which has become stale. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

While doing recovery, blocks are read from the raid5/6 disk one by one, so this is adding readahead so that we can read at most 256 contiguous blocks in one read IO. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

This updates recovery code to use the readahead helper. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

This is adding checksum to meta/data/parity resident on the raid5/6 log. So recovery now can verify checksum to see if anything inside meta/data/parity has been changed. If anything is wrong in meta block, we stops replaying data/parity at that position, while if anything is wrong in data/parity block, we just skip this this meta/data/parity pair and move onto the next one. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Currently there is a memory leak if we have an error while adding a raid5/6 log. Moreover, it didn't abort the transaction as others do, so this is fixing the broken error handling by applying two steps on initializing the log, step #1 is to allocate memory, check if it has a proper size, and step #2 is to assign the pointer in %fs_info. And by running step #1 ahead of starting transaction, we can gracefully bail out on errors now. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

We need to initialize the raid5/6 log after adding it, but we don't want to race with concurrent writes. So we initialize it before assigning the log pointer in %fs_info. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

A typical write to the raid5/6 log needs three steps: 1) collect data/parity pages into the bio in io_unit; 2) submit the bio in io_unit; 3) writeback data/parity to raid array in end_io. 1) and 2) are protected within log->io_mutex, while 3) is not. Since recovery needs to know the checkpoint offset where the highest successful writeback is, we cannot allow IO to be reordered. This is adding a list in which IO order is maintained properly. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

watchdog: BUG: soft lockup - CPU#6 stuck for 22s! [qemu-system-x86:10185] CPU: 6 PID: 10185 Comm: qemu-system-x86 Tainted: G OE 4.14.0-rc4+ #4 RIP: 0010:kvm_get_time_scale+0x4e/0xa0 [kvm] Call Trace: get_time_ref_counter+0x5a/0x80 [kvm] kvm_hv_process_stimers+0x120/0x5f0 [kvm] kvm_arch_vcpu_ioctl_run+0x4b4/0x1690 [kvm] kvm_vcpu_ioctl+0x33a/0x620 [kvm] do_vfs_ioctl+0xa1/0x5d0 SyS_ioctl+0x79/0x90 entry_SYSCALL_64_fastpath+0x1e/0xa9 This can be reproduced when running kvm-unit-tests/hyperv_stimer.flat and cpu-hotplug stress simultaneously. __this_cpu_read(cpu_tsc_khz) returns 0 (set in kvmclock_cpu_down_prep()) when the pCPU is unhotplug which results in kvm_get_time_scale() gets into an infinite loop. This patch fixes it by treating the unhotplug pCPU as not using master clock. Reviewed-by: Radim Krčmář <rkrcmar@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Jiri Pirko says: ==================== mlxsw: GRE offloading fixes Petr says: This patchset fixes a couple bugs in offloading GRE tunnels in mlxsw driver. Patch #1 fixes a problem that local routes pointing at a GRE tunnel device are offloaded even if that netdevice is down. Patch #2 detects that as a result of moving a GRE netdevice to a different VRF, two tunnels now have a conflict of local addresses, something that the mlxsw driver can't offload. Patch #3 fixes a FIB abort caused by forming a route pointing at a GRE tunnel that is eligible for offloading but already onloaded. Patch #4 fixes a problem that next hops migrated to a new RIF kept the old RIF reference, which went dangling shortly afterwards. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>

ni_create_attr_list uses WARN_ON to catch error cases while generating attribute list, which only prints out stack trace and may not be enough. This repalces them with more proper error handling flow. [ 59.666332] BUG: kernel NULL pointer dereference, address: 000000000000000e [ 59.673268] #PF: supervisor read access in kernel mode [ 59.678354] #PF: error_code(0x0000) - not-present page [ 59.682831] PGD 8000000005ff1067 P4D 8000000005ff1067 PUD 7dee067 PMD 0 [ 59.688556] Oops: 0000 [#1] PREEMPT SMP KASAN PTI [ 59.692642] CPU: 0 PID: 198 Comm: poc Tainted: G B W 6.2.0-rc1+ #4 [ 59.698868] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 [ 59.708795] RIP: 0010:ni_create_attr_list+0x505/0x860 [ 59.713657] Code: 7e 10 e8 5e d0 d0 ff 45 0f b7 76 10 48 8d 7b 16 e8 00 d1 d0 ff 66 44 89 73 16 4d 8d 75 0e 4c 89 f7 e8 3f d0 d0 ff 4c 8d8 [ 59.731559] RSP: 0018:ffff88800a56f1e0 EFLAGS: 00010282 [ 59.735691] RAX: 0000000000000001 RBX: ffff88800b7b5088 RCX: ffffffffb83079fe [ 59.741792] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffffbb7f9fc0 [ 59.748423] RBP: ffff88800a56f3a8 R08: ffff88800b7b50a0 R09: fffffbfff76ff3f9 [ 59.754654] R10: ffffffffbb7f9fc7 R11: fffffbfff76ff3f8 R12: ffff88800b756180 [ 59.761552] R13: 0000000000000000 R14: 000000000000000e R15: 0000000000000050 [ 59.768323] FS: 00007feaa8c96440(0000) GS:ffff88806d400000(0000) knlGS:0000000000000000 [ 59.776027] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 59.781395] CR2: 00007f3a2e0b1000 CR3: 000000000a5bc000 CR4: 00000000000006f0 [ 59.787607] Call Trace: [ 59.790271] <TASK> [ 59.792488] ? __pfx_ni_create_attr_list+0x10/0x10 [ 59.797235] ? kernel_text_address+0xd3/0xe0 [ 59.800856] ? unwind_get_return_address+0x3e/0x60 [ 59.805101] ? __kasan_check_write+0x18/0x20 [ 59.809296] ? preempt_count_sub+0x1c/0xd0 [ 59.813421] ni_ins_attr_ext+0x52c/0x5c0 [ 59.817034] ? __pfx_ni_ins_attr_ext+0x10/0x10 [ 59.821926] ? __vfs_setxattr+0x121/0x170 [ 59.825718] ? __vfs_setxattr_noperm+0x97/0x300 [ 59.829562] ? __vfs_setxattr_locked+0x145/0x170 [ 59.833987] ? vfs_setxattr+0x137/0x2a0 [ 59.836732] ? do_setxattr+0xce/0x150 [ 59.839807] ? setxattr+0x126/0x140 [ 59.842353] ? path_setxattr+0x164/0x180 [ 59.845275] ? __x64_sys_setxattr+0x71/0x90 [ 59.848838] ? do_syscall_64+0x3f/0x90 [ 59.851898] ? entry_SYSCALL_64_after_hwframe+0x72/0xdc [ 59.857046] ? stack_depot_save+0x17/0x20 [ 59.860299] ni_insert_attr+0x1ba/0x420 [ 59.863104] ? __pfx_ni_insert_attr+0x10/0x10 [ 59.867069] ? preempt_count_sub+0x1c/0xd0 [ 59.869897] ? _raw_spin_unlock_irqrestore+0x2b/0x50 [ 59.874088] ? __create_object+0x3ae/0x5d0 [ 59.877865] ni_insert_resident+0xc4/0x1c0 [ 59.881430] ? __pfx_ni_insert_resident+0x10/0x10 [ 59.886355] ? kasan_save_alloc_info+0x1f/0x30 [ 59.891117] ? __kasan_kmalloc+0x8b/0xa0 [ 59.894383] ntfs_set_ea+0x90d/0xbf0 [ 59.897703] ? __pfx_ntfs_set_ea+0x10/0x10 [ 59.901011] ? kernel_text_address+0xd3/0xe0 [ 59.905308] ? __kernel_text_address+0x16/0x50 [ 59.909811] ? unwind_get_return_address+0x3e/0x60 [ 59.914898] ? __pfx_stack_trace_consume_entry+0x10/0x10 [ 59.920250] ? arch_stack_walk+0xa2/0x100 [ 59.924560] ? filter_irq_stacks+0x27/0x80 [ 59.928722] ntfs_setxattr+0x405/0x440 [ 59.932512] ? __pfx_ntfs_setxattr+0x10/0x10 [ 59.936634] ? kvmalloc_node+0x2d/0x120 [ 59.940378] ? kasan_save_stack+0x41/0x60 [ 59.943870] ? kasan_save_stack+0x2a/0x60 [ 59.947719] ? kasan_set_track+0x29/0x40 [ 59.951417] ? kasan_save_alloc_info+0x1f/0x30 [ 59.955733] ? __kasan_kmalloc+0x8b/0xa0 [ 59.959598] ? __kmalloc_node+0x68/0x150 [ 59.963163] ? kvmalloc_node+0x2d/0x120 [ 59.966490] ? vmemdup_user+0x2b/0xa0 [ 59.969060] __vfs_setxattr+0x121/0x170 [ 59.972456] ? __pfx___vfs_setxattr+0x10/0x10 [ 59.976008] __vfs_setxattr_noperm+0x97/0x300 [ 59.981562] __vfs_setxattr_locked+0x145/0x170 [ 59.986100] vfs_setxattr+0x137/0x2a0 [ 59.989964] ? __pfx_vfs_setxattr+0x10/0x10 [ 59.993616] ? __kasan_check_write+0x18/0x20 [ 59.997425] do_setxattr+0xce/0x150 [ 60.000304] setxattr+0x126/0x140 [ 60.002967] ? __pfx_setxattr+0x10/0x10 [ 60.006471] ? __virt_addr_valid+0xcb/0x140 [ 60.010461] ? __call_rcu_common.constprop.0+0x1c7/0x330 [ 60.016037] ? debug_smp_processor_id+0x1b/0x30 [ 60.021008] ? kasan_quarantine_put+0x5b/0x190 [ 60.025545] ? putname+0x84/0xa0 [ 60.027910] ? __kasan_slab_free+0x11e/0x1b0 [ 60.031483] ? putname+0x84/0xa0 [ 60.033986] ? preempt_count_sub+0x1c/0xd0 [ 60.036876] ? __mnt_want_write+0xae/0x100 [ 60.040738] ? mnt_want_write+0x8f/0x150 [ 60.044317] path_setxattr+0x164/0x180 [ 60.048096] ? __pfx_path_setxattr+0x10/0x10 [ 60.052096] ? strncpy_from_user+0x175/0x1c0 [ 60.056482] ? debug_smp_processor_id+0x1b/0x30 [ 60.059848] ? fpregs_assert_state_consistent+0x6b/0x80 [ 60.064557] __x64_sys_setxattr+0x71/0x90 [ 60.068892] do_syscall_64+0x3f/0x90 [ 60.072868] entry_SYSCALL_64_after_hwframe+0x72/0xdc [ 60.077523] RIP: 0033:0x7feaa86e4469 [ 60.080915] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 088 [ 60.097353] RSP: 002b:00007ffdbd8311e8 EFLAGS: 00000286 ORIG_RAX: 00000000000000bc [ 60.103386] RAX: ffffffffffffffda RBX: 9461c5e290baac00 RCX: 00007feaa86e4469 [ 60.110322] RDX: 00007ffdbd831fe0 RSI: 00007ffdbd831305 RDI: 00007ffdbd831263 [ 60.116808] RBP: 00007ffdbd836180 R08: 0000000000000001 R09: 00007ffdbd836268 [ 60.123879] R10: 000000000000007d R11: 0000000000000286 R12: 0000000000400500 [ 60.130540] R13: 00007ffdbd836260 R14: 0000000000000000 R15: 0000000000000000 [ 60.136553] </TASK> [ 60.138818] Modules linked in: [ 60.141839] CR2: 000000000000000e [ 60.144831] ---[ end trace 0000000000000000 ]--- [ 60.149058] RIP: 0010:ni_create_attr_list+0x505/0x860 [ 60.153975] Code: 7e 10 e8 5e d0 d0 ff 45 0f b7 76 10 48 8d 7b 16 e8 00 d1 d0 ff 66 44 89 73 16 4d 8d 75 0e 4c 89 f7 e8 3f d0 d0 ff 4c 8d8 [ 60.172443] RSP: 0018:ffff88800a56f1e0 EFLAGS: 00010282 [ 60.176246] RAX: 0000000000000001 RBX: ffff88800b7b5088 RCX: ffffffffb83079fe [ 60.182752] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffffffffbb7f9fc0 [ 60.189949] RBP: ffff88800a56f3a8 R08: ffff88800b7b50a0 R09: fffffbfff76ff3f9 [ 60.196950] R10: ffffffffbb7f9fc7 R11: fffffbfff76ff3f8 R12: ffff88800b756180 [ 60.203671] R13: 0000000000000000 R14: 000000000000000e R15: 0000000000000050 [ 60.209595] FS: 00007feaa8c96440(0000) GS:ffff88806d400000(0000) knlGS:0000000000000000 [ 60.216299] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 60.222276] CR2: 00007f3a2e0b1000 CR3: 000000000a5bc000 CR4: 00000000000006f0 Signed-off-by: Edward Lo <loyuantsung@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>

ntfs_read_ea is called when we want to read extended attributes. There are some sanity checks for the validity of the EAs. However, it fails to return a proper error code for the inconsistent attributes, which might lead to unpredicted memory accesses after return. [ 138.916927] BUG: KASAN: use-after-free in ntfs_set_ea+0x453/0xbf0 [ 138.923876] Write of size 4 at addr ffff88800205cfac by task poc/199 [ 138.931132] [ 138.933016] CPU: 0 PID: 199 Comm: poc Not tainted 6.2.0-rc1+ #4 [ 138.938070] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 [ 138.947327] Call Trace: [ 138.949557] <TASK> [ 138.951539] dump_stack_lvl+0x4d/0x67 [ 138.956834] print_report+0x16f/0x4a6 [ 138.960798] ? ntfs_set_ea+0x453/0xbf0 [ 138.964437] ? kasan_complete_mode_report_info+0x7d/0x200 [ 138.969793] ? ntfs_set_ea+0x453/0xbf0 [ 138.973523] kasan_report+0xb8/0x140 [ 138.976740] ? ntfs_set_ea+0x453/0xbf0 [ 138.980578] __asan_store4+0x76/0xa0 [ 138.984669] ntfs_set_ea+0x453/0xbf0 [ 138.988115] ? __pfx_ntfs_set_ea+0x10/0x10 [ 138.993390] ? kernel_text_address+0xd3/0xe0 [ 138.998270] ? __kernel_text_address+0x16/0x50 [ 139.002121] ? unwind_get_return_address+0x3e/0x60 [ 139.005659] ? __pfx_stack_trace_consume_entry+0x10/0x10 [ 139.010177] ? arch_stack_walk+0xa2/0x100 [ 139.013657] ? filter_irq_stacks+0x27/0x80 [ 139.017018] ntfs_setxattr+0x405/0x440 [ 139.022151] ? __pfx_ntfs_setxattr+0x10/0x10 [ 139.026569] ? kvmalloc_node+0x2d/0x120 [ 139.030329] ? kasan_save_stack+0x41/0x60 [ 139.033883] ? kasan_save_stack+0x2a/0x60 [ 139.037338] ? kasan_set_track+0x29/0x40 [ 139.040163] ? kasan_save_alloc_info+0x1f/0x30 [ 139.043588] ? __kasan_kmalloc+0x8b/0xa0 [ 139.047255] ? __kmalloc_node+0x68/0x150 [ 139.051264] ? kvmalloc_node+0x2d/0x120 [ 139.055301] ? vmemdup_user+0x2b/0xa0 [ 139.058584] __vfs_setxattr+0x121/0x170 [ 139.062617] ? __pfx___vfs_setxattr+0x10/0x10 [ 139.066282] __vfs_setxattr_noperm+0x97/0x300 [ 139.070061] __vfs_setxattr_locked+0x145/0x170 [ 139.073580] vfs_setxattr+0x137/0x2a0 [ 139.076641] ? __pfx_vfs_setxattr+0x10/0x10 [ 139.080223] ? __kasan_check_write+0x18/0x20 [ 139.084234] do_setxattr+0xce/0x150 [ 139.087768] setxattr+0x126/0x140 [ 139.091250] ? __pfx_setxattr+0x10/0x10 [ 139.094948] ? __virt_addr_valid+0xcb/0x140 [ 139.097838] ? __call_rcu_common.constprop.0+0x1c7/0x330 [ 139.102688] ? debug_smp_processor_id+0x1b/0x30 [ 139.105985] ? kasan_quarantine_put+0x5b/0x190 [ 139.109980] ? putname+0x84/0xa0 [ 139.113886] ? __kasan_slab_free+0x11e/0x1b0 [ 139.117961] ? putname+0x84/0xa0 [ 139.121316] ? preempt_count_sub+0x1c/0xd0 [ 139.124427] ? __mnt_want_write+0xae/0x100 [ 139.127836] ? mnt_want_write+0x8f/0x150 [ 139.130954] path_setxattr+0x164/0x180 [ 139.133998] ? __pfx_path_setxattr+0x10/0x10 [ 139.137853] ? __pfx_ksys_pwrite64+0x10/0x10 [ 139.141299] ? debug_smp_processor_id+0x1b/0x30 [ 139.145714] ? fpregs_assert_state_consistent+0x6b/0x80 [ 139.150796] __x64_sys_setxattr+0x71/0x90 [ 139.155407] do_syscall_64+0x3f/0x90 [ 139.159035] entry_SYSCALL_64_after_hwframe+0x72/0xdc [ 139.163843] RIP: 0033:0x7f108cae4469 [ 139.166481] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 088 [ 139.183764] RSP: 002b:00007fff87588388 EFLAGS: 00000286 ORIG_RAX: 00000000000000bc [ 139.190657] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f108cae4469 [ 139.196586] RDX: 00007fff875883b0 RSI: 00007fff875883d1 RDI: 00007fff875883b6 [ 139.201716] RBP: 00007fff8758c530 R08: 0000000000000001 R09: 00007fff8758c618 [ 139.207940] R10: 0000000000000006 R11: 0000000000000286 R12: 00000000004004c0 [ 139.214007] R13: 00007fff8758c610 R14: 0000000000000000 R15: 0000000000000000 Signed-off-by: Edward Lo <loyuantsung@gmail.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>

…tnguy/net-queue Tony Nguyen says: ==================== igc: Fix corner cases for TSN offload Florian Kauer says: The igc driver supports several different offloading capabilities relevant in the TSN context. Recent patches in this area introduced regressions for certain corner cases that are fixed in this series. Each of the patches (except the first one) addresses a different regression that can be separately reproduced. Still, they have overlapping code changes so they should not be separately applied. Especially #4 and #6 address the same observation, but both need to be applied to avoid TX hang occurrences in the scenario described in the patches. ==================== Signed-off-by: Florian Kauer <florian.kauer@linutronix.de> Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>

…ed variables Hist triggers can have referenced variables without having direct variables fields. This can be the case if referenced variables are added for trigger actions. In this case the newly added references will not have field variables. Not taking such referenced variables into consideration can result in a bug where it would be possible to remove hist trigger with variables being refenced. This will result in a bug that is easily reproducable like so $ cd /sys/kernel/tracing $ echo 'synthetic_sys_enter char[] comm; long id' >> synthetic_events $ echo 'hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger $ echo 'hist:keys=common_pid.execname,id.syscall:onmatch(raw_syscalls.sys_enter).synthetic_sys_enter($comm, id)' >> events/raw_syscalls/sys_enter/trigger $ echo '!hist:keys=common_pid.execname,id.syscall:vals=hitcount:comm=common_pid.execname' >> events/raw_syscalls/sys_enter/trigger [ 100.263533] ================================================================== [ 100.264634] BUG: KASAN: slab-use-after-free in resolve_var_refs+0xc7/0x180 [ 100.265520] Read of size 8 at addr ffff88810375d0f0 by task bash/439 [ 100.266320] [ 100.266533] CPU: 2 PID: 439 Comm: bash Not tainted 6.5.0-rc1 #4 [ 100.267277] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-20220807_005459-localhost 04/01/2014 [ 100.268561] Call Trace: [ 100.268902] <TASK> [ 100.269189] dump_stack_lvl+0x4c/0x70 [ 100.269680] print_report+0xc5/0x600 [ 100.270165] ? resolve_var_refs+0xc7/0x180 [ 100.270697] ? kasan_complete_mode_report_info+0x80/0x1f0 [ 100.271389] ? resolve_var_refs+0xc7/0x180 [ 100.271913] kasan_report+0xbd/0x100 [ 100.272380] ? resolve_var_refs+0xc7/0x180 [ 100.272920] __asan_load8+0x71/0xa0 [ 100.273377] resolve_var_refs+0xc7/0x180 [ 100.273888] event_hist_trigger+0x749/0x860 [ 100.274505] ? kasan_save_stack+0x2a/0x50 [ 100.275024] ? kasan_set_track+0x29/0x40 [ 100.275536] ? __pfx_event_hist_trigger+0x10/0x10 [ 100.276138] ? ksys_write+0xd1/0x170 [ 100.276607] ? do_syscall_64+0x3c/0x90 [ 100.277099] ? entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ 100.277771] ? destroy_hist_data+0x446/0x470 [ 100.278324] ? event_hist_trigger_parse+0xa6c/0x3860 [ 100.278962] ? __pfx_event_hist_trigger_parse+0x10/0x10 [ 100.279627] ? __kasan_check_write+0x18/0x20 [ 100.280177] ? mutex_unlock+0x85/0xd0 [ 100.280660] ? __pfx_mutex_unlock+0x10/0x10 [ 100.281200] ? kfree+0x7b/0x120 [ 100.281619] ? ____kasan_slab_free+0x15d/0x1d0 [ 100.282197] ? event_trigger_write+0xac/0x100 [ 100.282764] ? __kasan_slab_free+0x16/0x20 [ 100.283293] ? __kmem_cache_free+0x153/0x2f0 [ 100.283844] ? sched_mm_cid_remote_clear+0xb1/0x250 [ 100.284550] ? __pfx_sched_mm_cid_remote_clear+0x10/0x10 [ 100.285221] ? event_trigger_write+0xbc/0x100 [ 100.285781] ? __kasan_check_read+0x15/0x20 [ 100.286321] ? __bitmap_weight+0x66/0xa0 [ 100.286833] ? _find_next_bit+0x46/0xe0 [ 100.287334] ? task_mm_cid_work+0x37f/0x450 [ 100.287872] event_triggers_call+0x84/0x150 [ 100.288408] trace_event_buffer_commit+0x339/0x430 [ 100.289073] ? ring_buffer_event_data+0x3f/0x60 [ 100.292189] trace_event_raw_event_sys_enter+0x8b/0xe0 [ 100.295434] syscall_trace_enter.constprop.0+0x18f/0x1b0 [ 100.298653] syscall_enter_from_user_mode+0x32/0x40 [ 100.301808] do_syscall_64+0x1a/0x90 [ 100.304748] entry_SYSCALL_64_after_hwframe+0x6e/0xd8 [ 100.307775] RIP: 0033:0x7f686c75c1cb [ 100.310617] Code: 73 01 c3 48 8b 0d 65 3c 10 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 21 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 35 3c 10 00 f7 d8 64 89 01 48 [ 100.317847] RSP: 002b:00007ffc60137a38 EFLAGS: 00000246 ORIG_RAX: 0000000000000021 [ 100.321200] RAX: ffffffffffffffda RBX: 000055f566469ea0 RCX: 00007f686c75c1cb [ 100.324631] RDX: 0000000000000001 RSI: 0000000000000001 RDI: 000000000000000a [ 100.328104] RBP: 00007ffc60137ac0 R08: 00007f686c818460 R09: 000000000000000a [ 100.331509] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000009 [ 100.334992] R13: 0000000000000007 R14: 000000000000000a R15: 0000000000000007 [ 100.338381] </TASK> We hit the bug because when second hist trigger has was created has_hist_vars() returned false because hist trigger did not have variables. As a result of that save_hist_vars() was not called to add the trigger to trace_array->hist_vars. Later on when we attempted to remove the first histogram find_any_var_ref() failed to detect it is being used because it did not find the second trigger in hist_vars list. With this change we wait until trigger actions are created so we can take into consideration if hist trigger has variable references. Also, now we check the return value of save_hist_vars() and fail trigger creation if save_hist_vars() fails. Link: https://lore.kernel.org/linux-trace-kernel/20230712223021.636335-1-mkhalfella@purestorage.com Cc: stable@vger.kernel.org Fixes: 067fe03 ("tracing: Add variable reference handling to hist triggers") Signed-off-by: Mohamed Khalfella <mkhalfella@purestorage.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

sk->sk_state indicates whether iso_pi(sk)->conn is valid. Operations that check/update sk_state and access conn should hold lock_sock, otherwise they can race. The order of taking locks is hci_dev_lock > lock_sock > iso_conn_lock, which is how it is in connect/disconnect_cfm -> iso_conn_del -> iso_chan_del. Fix locking in iso_connect_cis/bis and sendmsg/recvmsg to take lock_sock around updating sk_state and conn. iso_conn_del must not occur during iso_connect_cis/bis, as it frees the iso_conn. Hold hdev->lock longer to prevent that. This should not reintroduce the issue fixed in commit 241f519 ("Bluetooth: ISO: Avoid circular locking dependency"), since the we acquire locks in order. We retain the fix in iso_sock_connect to release lock_sock before iso_connect_* acquires hdev->lock. Similarly for commit 6a5ad25 ("Bluetooth: ISO: Fix possible circular locking dependency"). We retain the fix in iso_conn_ready to not acquire iso_conn_lock before lock_sock. iso_conn_add shall return iso_conn with valid hcon. Make it so also when reusing an old CIS connection waiting for disconnect timeout (see __iso_sock_close where conn->hcon is set to NULL). Trace with iso_conn_del after iso_chan_add in iso_connect_cis: =============================================================== iso_sock_create:771: sock 00000000be9b69b7 iso_sock_init:693: sk 000000004dff667e iso_sock_bind:827: sk 000000004dff667e 70:1a:b8:98:ff:a2 type 1 iso_sock_setsockopt:1289: sk 000000004dff667e iso_sock_setsockopt:1289: sk 000000004dff667e iso_sock_setsockopt:1289: sk 000000004dff667e iso_sock_connect:875: sk 000000004dff667e iso_connect_cis:353: 70:1a:b8:98:ff:a2 -> 28:3d:c2:4a:7e:da hci_get_route:1199: 70:1a:b8:98:ff:a2 -> 28:3d:c2:4a:7e:da hci_conn_add:1005: hci0 dst 28:3d:c2:4a:7e:da iso_conn_add:140: hcon 000000007b65d182 conn 00000000daf8625e __iso_chan_add:214: conn 00000000daf8625e iso_connect_cfm:1700: hcon 000000007b65d182 bdaddr 28:3d:c2:4a:7e:da status 12 iso_conn_del:187: hcon 000000007b65d182 conn 00000000daf8625e, err 16 iso_sock_clear_timer:117: sock 000000004dff667e state 3 <Note: sk_state is BT_BOUND (3), so iso_connect_cis is still running at this point> iso_chan_del:153: sk 000000004dff667e, conn 00000000daf8625e, err 16 hci_conn_del:1151: hci0 hcon 000000007b65d182 handle 65535 hci_conn_unlink:1102: hci0: hcon 000000007b65d182 hci_chan_list_flush:2780: hcon 000000007b65d182 iso_sock_getsockopt:1376: sk 000000004dff667e iso_sock_getname:1070: sock 00000000be9b69b7, sk 000000004dff667e iso_sock_getname:1070: sock 00000000be9b69b7, sk 000000004dff667e iso_sock_getsockopt:1376: sk 000000004dff667e iso_sock_getname:1070: sock 00000000be9b69b7, sk 000000004dff667e iso_sock_getname:1070: sock 00000000be9b69b7, sk 000000004dff667e iso_sock_shutdown:1434: sock 00000000be9b69b7, sk 000000004dff667e, how 1 __iso_sock_close:632: sk 000000004dff667e state 5 socket 00000000be9b69b7 <Note: sk_state is BT_CONNECT (5), even though iso_chan_del sets BT_CLOSED (6). Only iso_connect_cis sets it to BT_CONNECT, so it must be that iso_chan_del occurred between iso_chan_add and end of iso_connect_cis.> BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 8000000006467067 P4D 8000000006467067 PUD 3f5f067 PMD 0 Oops: 0000 [#1] PREEMPT SMP PTI Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 RIP: 0010:__iso_sock_close (net/bluetooth/iso.c:664) bluetooth =============================================================== Trace with iso_conn_del before iso_chan_add in iso_connect_cis: =============================================================== iso_connect_cis:356: 70:1a:b8:98:ff:a2 -> 28:3d:c2:4a:7e:da ... iso_conn_add:140: hcon 0000000093bc551f conn 00000000768ae504 hci_dev_put:1487: hci0 orig refcnt 21 hci_event_packet:7607: hci0: event 0x0e hci_cmd_complete_evt:4231: hci0: opcode 0x2062 hci_cc_le_set_cig_params:3846: hci0: status 0x07 hci_sent_cmd_data:3107: hci0 opcode 0x2062 iso_connect_cfm:1703: hcon 0000000093bc551f bdaddr 28:3d:c2:4a:7e:da status 7 iso_conn_del:187: hcon 0000000093bc551f conn 00000000768ae504, err 12 hci_conn_del:1151: hci0 hcon 0000000093bc551f handle 65535 hci_conn_unlink:1102: hci0: hcon 0000000093bc551f hci_chan_list_flush:2780: hcon 0000000093bc551f __iso_chan_add:214: conn 00000000768ae504 <Note: this conn was already freed in iso_conn_del above> iso_sock_clear_timer:117: sock 0000000098323f95 state 3 general protection fault, probably for non-canonical address 0x30b29c630930aec8: 0000 [#1] PREEMPT SMP PTI CPU: 1 PID: 1920 Comm: bluetoothd Tainted: G E 6.3.0-rc7+ #4 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 RIP: 0010:detach_if_pending+0x28/0xd0 Code: 90 90 0f 1f 44 00 00 48 8b 47 08 48 85 c0 0f 84 ad 00 00 00 55 89 d5 53 48 83 3f 00 48 89 fb 74 7d 66 90 48 8b 03 48 8b 53 08 <> RSP: 0018:ffffb90841a67d08 EFLAGS: 00010007 RAX: 0000000000000000 RBX: ffff9141bd5061b8 RCX: 0000000000000000 RDX: 30b29c630930aec8 RSI: ffff9141fdd21e80 RDI: ffff9141bd5061b8 RBP: 0000000000000001 R08: 0000000000000000 R09: ffffb90841a67b88 R10: 0000000000000003 R11: ffffffff8613f558 R12: ffff9141fdd21e80 R13: 0000000000000000 R14: ffff9141b5976010 R15: ffff914185755338 FS: 00007f45768bd840(0000) GS:ffff9141fdd00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000619000424074 CR3: 0000000009f5e005 CR4: 0000000000170ee0 Call Trace: <TASK> timer_delete+0x48/0x80 try_to_grab_pending+0xdf/0x170 __cancel_work+0x37/0xb0 iso_connect_cis+0x141/0x400 [bluetooth] =============================================================== Trace with NULL conn->hcon in state BT_CONNECT: =============================================================== __iso_sock_close:619: sk 00000000f7c71fc5 state 1 socket 00000000d90c5fe5 ... __iso_sock_close:619: sk 00000000f7c71fc5 state 8 socket 00000000d90c5fe5 iso_chan_del:153: sk 00000000f7c71fc5, conn 0000000022c03a7e, err 104 ... iso_sock_connect:862: sk 00000000129b56c3 iso_connect_cis:348: 70:1a:b8:98:ff:a2 -> 28:3d:c2:4a:7d:2a hci_get_route:1199: 70:1a:b8:98:ff:a2 -> 28:3d:c2:4a:7d:2a hci_dev_hold:1495: hci0 orig refcnt 19 __iso_chan_add:214: conn 0000000022c03a7e <Note: reusing old conn> iso_sock_clear_timer:117: sock 00000000129b56c3 state 3 ... iso_sock_ready:1485: sk 00000000129b56c3 ... iso_sock_sendmsg:1077: sock 00000000e5013966, sk 00000000129b56c3 BUG: kernel NULL pointer dereference, address: 00000000000006a8 PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP PTI CPU: 1 PID: 1403 Comm: wireplumber Tainted: G E 6.3.0-rc7+ #4 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-1.fc38 04/01/2014 RIP: 0010:iso_sock_sendmsg+0x63/0x2a0 [bluetooth] =============================================================== Fixes: 241f519 ("Bluetooth: ISO: Avoid circular locking dependency") Fixes: 6a5ad25 ("Bluetooth: ISO: Fix possible circular locking dependency") Signed-off-by: Pauli Virtanen <pav@iki.fi> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

syzkaller found a bug in unix_bind_bsd() [0]. We can reproduce it by bind()ing a socket on a path with length 108. 108 is the size of sun_addr of struct sockaddr_un and is the maximum valid length for the pathname socket. When calling bind(), we use struct sockaddr_storage as the actual buffer size, so terminating sun_addr[108] with null is legitimate as done in unix_mkname_bsd(). However, strlen(sunaddr) for such a case causes fortify_panic() if CONFIG_FORTIFY_SOURCE=y. __fortify_strlen() has no idea about the actual buffer size and see the string as unterminated. Let's use strnlen() to allow sun_addr to be unterminated at 107. [0]: detected buffer overflow in __fortify_strlen kernel BUG at lib/string_helpers.c:1031! Internal error: Oops - BUG: 00000000f2000800 [#1] PREEMPT SMP Modules linked in: CPU: 0 PID: 255 Comm: syz-executor296 Not tainted 6.5.0-rc1-00330-g60cc1f7d0605 #4 Hardware name: linux,dummy-virt (DT) pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : fortify_panic+0x1c/0x20 lib/string_helpers.c:1030 lr : fortify_panic+0x1c/0x20 lib/string_helpers.c:1030 sp : ffff800089817af0 x29: ffff800089817af0 x28: ffff800089817b40 x27: 1ffff00011302f68 x26: 000000000000006e x25: 0000000000000012 x24: ffff800087e60140 x23: dfff800000000000 x22: ffff800089817c20 x21: ffff800089817c8e x20: 000000000000006c x19: ffff00000c323900 x18: ffff800086ab1630 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000001 x14: 1ffff00011302eb8 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 64a26b65474d2a00 x8 : 64a26b65474d2a00 x7 : 0000000000000001 x6 : 0000000000000001 x5 : ffff800089817438 x4 : ffff800086ac99e0 x3 : ffff800080f19e8c x2 : 0000000000000001 x1 : 0000000100000000 x0 : 000000000000002c Call trace: fortify_panic+0x1c/0x20 lib/string_helpers.c:1030 _Z16__fortify_strlenPKcU25pass_dynamic_object_size1 include/linux/fortify-string.h:217 [inline] unix_bind_bsd net/unix/af_unix.c:1212 [inline] unix_bind+0xba8/0xc58 net/unix/af_unix.c:1326 __sys_bind+0x1ac/0x248 net/socket.c:1792 __do_sys_bind net/socket.c:1803 [inline] __se_sys_bind net/socket.c:1801 [inline] __arm64_sys_bind+0x7c/0x94 net/socket.c:1801 __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline] invoke_syscall+0x98/0x2c0 arch/arm64/kernel/syscall.c:52 el0_svc_common+0x134/0x240 arch/arm64/kernel/syscall.c:139 do_el0_svc+0x64/0x198 arch/arm64/kernel/syscall.c:188 el0_svc+0x2c/0x7c arch/arm64/kernel/entry-common.c:647 el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:665 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591 Code: aa0003e1 d0000e80 91030000 97ffc91a (d4210000) Fixes: df8fc4e ("kbuild: Enable -fstrict-flex-arrays=3") Reported-by: syzkaller <syzkaller@googlegroups.com> Suggested-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230724213425.22920-2-kuniyu@amazon.com Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>

syzkaller found a warning in packet_getname() [0], where we try to copy 16 bytes to sockaddr_ll.sll_addr[8]. Some devices (ip6gre, vti6, ip6tnl) have 16 bytes address expressed by struct in6_addr. Also, Infiniband has 32 bytes as MAX_ADDR_LEN. The write seems to overflow, but actually not since we use struct sockaddr_storage defined in __sys_getsockname() and its size is 128 (_K_SS_MAXSIZE) bytes. Thus, we have sufficient room after sll_addr[] as __data[]. To avoid the warning, let's add a flex array member union-ed with sll_addr. Another option would be to use strncpy() and limit the copied length to sizeof(sll_addr), but it will return the partial address and break an application that passes sockaddr_storage to getsockname(). [0]: memcpy: detected field-spanning write (size 16) of single field "sll->sll_addr" at net/packet/af_packet.c:3604 (size 8) WARNING: CPU: 0 PID: 255 at net/packet/af_packet.c:3604 packet_getname+0x25c/0x3a0 net/packet/af_packet.c:3604 Modules linked in: CPU: 0 PID: 255 Comm: syz-executor750 Not tainted 6.5.0-rc1-00330-g60cc1f7d0605 #4 Hardware name: linux,dummy-virt (DT) pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : packet_getname+0x25c/0x3a0 net/packet/af_packet.c:3604 lr : packet_getname+0x25c/0x3a0 net/packet/af_packet.c:3604 sp : ffff800089887bc0 x29: ffff800089887bc0 x28: ffff000010f80f80 x27: 0000000000000003 x26: dfff800000000000 x25: ffff700011310f80 x24: ffff800087d55000 x23: dfff800000000000 x22: ffff800089887c2c x21: 0000000000000010 x20: ffff00000de08310 x19: ffff800089887c20 x18: ffff800086ab1630 x17: 20646c6569662065 x16: 6c676e697320666f x15: 0000000000000001 x14: 1fffe0000d56d7ca x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 3e60944c3da92b00 x8 : 3e60944c3da92b00 x7 : 0000000000000001 x6 : 0000000000000001 x5 : ffff8000898874f8 x4 : ffff800086ac99e0 x3 : ffff8000803f8808 x2 : 0000000000000001 x1 : 0000000100000000 x0 : 0000000000000000 Call trace: packet_getname+0x25c/0x3a0 net/packet/af_packet.c:3604 __sys_getsockname+0x168/0x24c net/socket.c:2042 __do_sys_getsockname net/socket.c:2057 [inline] __se_sys_getsockname net/socket.c:2054 [inline] __arm64_sys_getsockname+0x7c/0x94 net/socket.c:2054 __invoke_syscall arch/arm64/kernel/syscall.c:38 [inline] invoke_syscall+0x98/0x2c0 arch/arm64/kernel/syscall.c:52 el0_svc_common+0x134/0x240 arch/arm64/kernel/syscall.c:139 do_el0_svc+0x64/0x198 arch/arm64/kernel/syscall.c:188 el0_svc+0x2c/0x7c arch/arm64/kernel/entry-common.c:647 el0t_64_sync_handler+0x84/0xfc arch/arm64/kernel/entry-common.c:665 el0t_64_sync+0x190/0x194 arch/arm64/kernel/entry.S:591 Fixes: df8fc4e ("kbuild: Enable -fstrict-flex-arrays=3") Reported-by: syzkaller <syzkaller@googlegroups.com> Suggested-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230724213425.22920-3-kuniyu@amazon.com Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The cited commit holds encap tbl lock unconditionally when setting up dests. But it may cause the following deadlock: PID: 1063722 TASK: ffffa062ca5d0000 CPU: 13 COMMAND: "handler8" #0 [ffffb14de05b7368] __schedule at ffffffffa1d5aa91 #1 [ffffb14de05b7410] schedule at ffffffffa1d5afdb #2 [ffffb14de05b7430] schedule_preempt_disabled at ffffffffa1d5b528 #3 [ffffb14de05b7440] __mutex_lock at ffffffffa1d5d6cb #4 [ffffb14de05b74e8] mutex_lock_nested at ffffffffa1d5ddeb #5 [ffffb14de05b74f8] mlx5e_tc_tun_encap_dests_set at ffffffffc12f2096 [mlx5_core] #6 [ffffb14de05b7568] post_process_attr at ffffffffc12d9fc5 [mlx5_core] #7 [ffffb14de05b75a0] mlx5e_tc_add_fdb_flow at ffffffffc12de877 [mlx5_core] torvalds#8 [ffffb14de05b75f0] __mlx5e_add_fdb_flow at ffffffffc12e0eef [mlx5_core] torvalds#9 [ffffb14de05b7660] mlx5e_tc_add_flow at ffffffffc12e12f7 [mlx5_core] torvalds#10 [ffffb14de05b76b8] mlx5e_configure_flower at ffffffffc12e1686 [mlx5_core] torvalds#11 [ffffb14de05b7720] mlx5e_rep_indr_offload at ffffffffc12e3817 [mlx5_core] #12 [ffffb14de05b7730] mlx5e_rep_indr_setup_tc_cb at ffffffffc12e388a [mlx5_core] #13 [ffffb14de05b7740] tc_setup_cb_add at ffffffffa1ab2ba8 torvalds#14 [ffffb14de05b77a0] fl_hw_replace_filter at ffffffffc0bdec2f [cls_flower] #15 [ffffb14de05b7868] fl_change at ffffffffc0be6caa [cls_flower] #16 [ffffb14de05b7908] tc_new_tfilter at ffffffffa1ab71f0 [1031218.028143] wait_for_completion+0x24/0x30 [1031218.028589] mlx5e_update_route_decap_flows+0x9a/0x1e0 [mlx5_core] [1031218.029256] mlx5e_tc_fib_event_work+0x1ad/0x300 [mlx5_core] [1031218.029885] process_one_work+0x24e/0x510 Actually no need to hold encap tbl lock if there is no encap action. Fix it by checking if encap action exists or not before holding encap tbl lock. Fixes: 37c3b9f ("net/mlx5e: Prevent encap offload when neigh update is running") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Noticed with: make EXTRA_CFLAGS="-fsanitize=address" BUILD_BPF_SKEL=1 CORESIGHT=1 O=/tmp/build/perf-tools-next -C tools/perf install-bin Direct leak of 45 byte(s) in 1 object(s) allocated from: #0 0x7f213f87243b in strdup (/lib64/libasan.so.8+0x7243b) #1 0x63d15f in evsel__set_filter util/evsel.c:1371 #2 0x63d15f in evsel__append_filter util/evsel.c:1387 #3 0x63d15f in evsel__append_tp_filter util/evsel.c:1400 #4 0x62cd52 in evlist__append_tp_filter util/evlist.c:1145 #5 0x62cd52 in evlist__append_tp_filter_pids util/evlist.c:1196 #6 0x541e49 in trace__set_filter_loop_pids /home/acme/git/perf-tools/tools/perf/builtin-trace.c:3646 #7 0x541e49 in trace__set_filter_pids /home/acme/git/perf-tools/tools/perf/builtin-trace.c:3670 torvalds#8 0x541e49 in trace__run /home/acme/git/perf-tools/tools/perf/builtin-trace.c:3970 torvalds#9 0x541e49 in cmd_trace /home/acme/git/perf-tools/tools/perf/builtin-trace.c:5141 torvalds#10 0x5ef1a2 in run_builtin /home/acme/git/perf-tools/tools/perf/perf.c:323 torvalds#11 0x4196da in handle_internal_command /home/acme/git/perf-tools/tools/perf/perf.c:377 #12 0x4196da in run_argv /home/acme/git/perf-tools/tools/perf/perf.c:421 #13 0x4196da in main /home/acme/git/perf-tools/tools/perf/perf.c:537 torvalds#14 0x7f213e84a50f in __libc_start_call_main (/lib64/libc.so.6+0x2750f) Free it on evsel__exit(). Acked-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/lkml/20230719202951.534582-2-acme@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

To plug these leaks detected with: $ make EXTRA_CFLAGS="-fsanitize=address" BUILD_BPF_SKEL=1 CORESIGHT=1 O=/tmp/build/perf-tools-next -C tools/perf install-bin ================================================================= ==473890==ERROR: LeakSanitizer: detected memory leaks Direct leak of 112 byte(s) in 1 object(s) allocated from: #0 0x7fdf19aba097 in calloc (/lib64/libasan.so.8+0xba097) #1 0x987836 in zalloc (/home/acme/bin/perf+0x987836) #2 0x5367ae in thread_trace__new /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:1289 #3 0x5367ae in thread__trace /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:1307 #4 0x5367ae in trace__sys_exit /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:2468 #5 0x52bf34 in trace__handle_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3177 #6 0x52bf34 in __trace__deliver_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3685 #7 0x542927 in trace__deliver_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3712 torvalds#8 0x542927 in trace__run /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:4055 torvalds#9 0x542927 in cmd_trace /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:5141 torvalds#10 0x5ef1a2 in run_builtin /home/acme/git/perf-tools-next/tools/perf/perf.c:323 torvalds#11 0x4196da in handle_internal_command /home/acme/git/perf-tools-next/tools/perf/perf.c:377 #12 0x4196da in run_argv /home/acme/git/perf-tools-next/tools/perf/perf.c:421 #13 0x4196da in main /home/acme/git/perf-tools-next/tools/perf/perf.c:537 torvalds#14 0x7fdf18a4a50f in __libc_start_call_main (/lib64/libc.so.6+0x2750f) Direct leak of 2048 byte(s) in 1 object(s) allocated from: #0 0x7f788fcba6af in __interceptor_malloc (/lib64/libasan.so.8+0xba6af) #1 0x5337c0 in trace__sys_enter /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:2342 #2 0x52bfb4 in trace__handle_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3191 #3 0x52bfb4 in __trace__deliver_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3699 #4 0x542883 in trace__deliver_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3726 #5 0x542883 in trace__run /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:4069 #6 0x542883 in cmd_trace /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:5155 #7 0x5ef232 in run_builtin /home/acme/git/perf-tools-next/tools/perf/perf.c:323 torvalds#8 0x4196da in handle_internal_command /home/acme/git/perf-tools-next/tools/perf/perf.c:377 torvalds#9 0x4196da in run_argv /home/acme/git/perf-tools-next/tools/perf/perf.c:421 torvalds#10 0x4196da in main /home/acme/git/perf-tools-next/tools/perf/perf.c:537 torvalds#11 0x7f788ec4a50f in __libc_start_call_main (/lib64/libc.so.6+0x2750f) Indirect leak of 48 byte(s) in 1 object(s) allocated from: #0 0x7fdf19aba6af in __interceptor_malloc (/lib64/libasan.so.8+0xba6af) #1 0x77b335 in intlist__new util/intlist.c:116 #2 0x5367fd in thread_trace__new /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:1293 #3 0x5367fd in thread__trace /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:1307 #4 0x5367fd in trace__sys_exit /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:2468 #5 0x52bf34 in trace__handle_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3177 #6 0x52bf34 in __trace__deliver_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3685 #7 0x542927 in trace__deliver_event /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3712 torvalds#8 0x542927 in trace__run /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:4055 torvalds#9 0x542927 in cmd_trace /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:5141 torvalds#10 0x5ef1a2 in run_builtin /home/acme/git/perf-tools-next/tools/perf/perf.c:323 torvalds#11 0x4196da in handle_internal_command /home/acme/git/perf-tools-next/tools/perf/perf.c:377 #12 0x4196da in run_argv /home/acme/git/perf-tools-next/tools/perf/perf.c:421 #13 0x4196da in main /home/acme/git/perf-tools-next/tools/perf/perf.c:537 torvalds#14 0x7fdf18a4a50f in __libc_start_call_main (/lib64/libc.so.6+0x2750f) Acked-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/lkml/20230719202951.534582-4-acme@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

In 3cb4d5e ("perf trace: Free syscall tp fields in evsel->priv") it only was freeing if strcmp(evsel->tp_format->system, "syscalls") returned zero, while the corresponding initialization of evsel->priv was being performed if it was _not_ zero, i.e. if the tp system wasn't 'syscalls'. Just stop looking for that and free it if evsel->priv was set, which should be equivalent. Also use the pre-existing evsel_trace__delete() function. This resolves these leaks, detected with: $ make EXTRA_CFLAGS="-fsanitize=address" BUILD_BPF_SKEL=1 CORESIGHT=1 O=/tmp/build/perf-tools-next -C tools/perf install-bin ================================================================= ==481565==ERROR: LeakSanitizer: detected memory leaks Direct leak of 40 byte(s) in 1 object(s) allocated from: #0 0x7f7343cba097 in calloc (/lib64/libasan.so.8+0xba097) #1 0x987966 in zalloc (/home/acme/bin/perf+0x987966) #2 0x52f9b9 in evsel_trace__new /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:307 #3 0x52f9b9 in evsel__syscall_tp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:333 #4 0x52f9b9 in evsel__init_raw_syscall_tp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:458 #5 0x52f9b9 in perf_evsel__raw_syscall_newtp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:480 #6 0x540e8b in trace__add_syscall_newtp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3212 #7 0x540e8b in trace__run /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3891 torvalds#8 0x540e8b in cmd_trace /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:5156 torvalds#9 0x5ef262 in run_builtin /home/acme/git/perf-tools-next/tools/perf/perf.c:323 torvalds#10 0x4196da in handle_internal_command /home/acme/git/perf-tools-next/tools/perf/perf.c:377 torvalds#11 0x4196da in run_argv /home/acme/git/perf-tools-next/tools/perf/perf.c:421 #12 0x4196da in main /home/acme/git/perf-tools-next/tools/perf/perf.c:537 #13 0x7f7342c4a50f in __libc_start_call_main (/lib64/libc.so.6+0x2750f) Direct leak of 40 byte(s) in 1 object(s) allocated from: #0 0x7f7343cba097 in calloc (/lib64/libasan.so.8+0xba097) #1 0x987966 in zalloc (/home/acme/bin/perf+0x987966) #2 0x52f9b9 in evsel_trace__new /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:307 #3 0x52f9b9 in evsel__syscall_tp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:333 #4 0x52f9b9 in evsel__init_raw_syscall_tp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:458 #5 0x52f9b9 in perf_evsel__raw_syscall_newtp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:480 #6 0x540dd1 in trace__add_syscall_newtp /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3205 #7 0x540dd1 in trace__run /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:3891 torvalds#8 0x540dd1 in cmd_trace /home/acme/git/perf-tools-next/tools/perf/builtin-trace.c:5156 torvalds#9 0x5ef262 in run_builtin /home/acme/git/perf-tools-next/tools/perf/perf.c:323 torvalds#10 0x4196da in handle_internal_command /home/acme/git/perf-tools-next/tools/perf/perf.c:377 torvalds#11 0x4196da in run_argv /home/acme/git/perf-tools-next/tools/perf/perf.c:421 #12 0x4196da in main /home/acme/git/perf-tools-next/tools/perf/perf.c:537 #13 0x7f7342c4a50f in __libc_start_call_main (/lib64/libc.so.6+0x2750f) SUMMARY: AddressSanitizer: 80 byte(s) leaked in 2 allocation(s). [root@quaco ~]# With this we plug all leaks with "perf trace sleep 1". Fixes: 3cb4d5e ("perf trace: Free syscall tp fields in evsel->priv") Acked-by: Ian Rogers <irogers@google.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Link: https://lore.kernel.org/lkml/20230719202951.534582-5-acme@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

…failure to add a probe Building perf with EXTRA_CFLAGS="-fsanitize=address" a leak is detect when trying to add a probe to a non-existent function: # perf probe -x ~/bin/perf dso__neW Probe point 'dso__neW' not found. Error: Failed to add events. ================================================================= ==296634==ERROR: LeakSanitizer: detected memory leaks Direct leak of 128 byte(s) in 1 object(s) allocated from: #0 0x7f67642ba097 in calloc (/lib64/libasan.so.8+0xba097) #1 0x7f67641a76f1 in allocate_cfi (/lib64/libdw.so.1+0x3f6f1) Direct leak of 65 byte(s) in 1 object(s) allocated from: #0 0x7f67642b95b5 in __interceptor_realloc.part.0 (/lib64/libasan.so.8+0xb95b5) #1 0x6cac75 in strbuf_grow util/strbuf.c:64 #2 0x6ca934 in strbuf_init util/strbuf.c:25 #3 0x9337d2 in synthesize_perf_probe_point util/probe-event.c:2018 #4 0x92be51 in try_to_find_probe_trace_events util/probe-event.c:964 #5 0x93d5c6 in convert_to_probe_trace_events util/probe-event.c:3512 #6 0x93d6d5 in convert_perf_probe_events util/probe-event.c:3529 #7 0x56f37f in perf_add_probe_events /var/home/acme/git/perf-tools-next/tools/perf/builtin-probe.c:354 torvalds#8 0x572fbc in __cmd_probe /var/home/acme/git/perf-tools-next/tools/perf/builtin-probe.c:738 torvalds#9 0x5730f2 in cmd_probe /var/home/acme/git/perf-tools-next/tools/perf/builtin-probe.c:766 torvalds#10 0x635d81 in run_builtin /var/home/acme/git/perf-tools-next/tools/perf/perf.c:323 torvalds#11 0x6362c1 in handle_internal_command /var/home/acme/git/perf-tools-next/tools/perf/perf.c:377 #12 0x63667a in run_argv /var/home/acme/git/perf-tools-next/tools/perf/perf.c:421 #13 0x636b8d in main /var/home/acme/git/perf-tools-next/tools/perf/perf.c:537 torvalds#14 0x7f676302950f in __libc_start_call_main (/lib64/libc.so.6+0x2950f) SUMMARY: AddressSanitizer: 193 byte(s) leaked in 2 allocation(s). # synthesize_perf_probe_point() returns a "detachec" strbuf, i.e. a malloc'ed string that needs to be free'd. An audit will be performed to find other such cases. Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/lkml/ZM0l1Oxamr4SVjfY@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

While debugging a segfault on 'perf lock contention' without an available perf.data file I noticed that it was basically calling: perf_session__delete(ERR_PTR(-1)) Resulting in: (gdb) run lock contention Starting program: /root/bin/perf lock contention [Thread debugging using libthread_db enabled] Using host libthread_db library "/lib64/libthread_db.so.1". failed to open perf.data: No such file or directory (try 'perf record' first) Initializing perf session failed Program received signal SIGSEGV, Segmentation fault. 0x00000000005e7515 in auxtrace__free (session=0xffffffffffffffff) at util/auxtrace.c:2858 2858 if (!session->auxtrace) (gdb) p session $1 = (struct perf_session *) 0xffffffffffffffff (gdb) bt #0 0x00000000005e7515 in auxtrace__free (session=0xffffffffffffffff) at util/auxtrace.c:2858 #1 0x000000000057bb4d in perf_session__delete (session=0xffffffffffffffff) at util/session.c:300 #2 0x000000000047c421 in __cmd_contention (argc=0, argv=0x7fffffffe200) at builtin-lock.c:2161 #3 0x000000000047dc95 in cmd_lock (argc=0, argv=0x7fffffffe200) at builtin-lock.c:2604 #4 0x0000000000501466 in run_builtin (p=0xe597a8 <commands+552>, argc=2, argv=0x7fffffffe200) at perf.c:322 #5 0x00000000005016d5 in handle_internal_command (argc=2, argv=0x7fffffffe200) at perf.c:375 #6 0x0000000000501824 in run_argv (argcp=0x7fffffffe02c, argv=0x7fffffffe020) at perf.c:419 #7 0x0000000000501b11 in main (argc=2, argv=0x7fffffffe200) at perf.c:535 (gdb) So just set it to NULL after using PTR_ERR(session) to decode the error as perf_session__delete(NULL) is supported. The same problem was found in 'perf top' after an audit of all perf_session__new() failure handling. Fixes: 6ef81c5 ("perf session: Return error code for perf_session__new() function on failure") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jeremie Galarneau <jeremie.galarneau@efficios.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Mamatha Inamdar <mamatha4@linux.vnet.ibm.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Nageswara R Sastry <rnsastry@linux.vnet.ibm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Shawn Landden <shawn@git.icu> Cc: Song Liu <songliubraving@fb.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com> Link: https://lore.kernel.org/lkml/ZN4Q2rxxsL08A8rd@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

When COWing a relocation tree path, at relocation.c:replace_path(), we can trigger a lockdep splat while we are in the btrfs_search_slot() call against the relocation root. This happens in that callchain at ctree.c:read_block_for_search() when we happen to find a child extent buffer already loaded through the fs tree with a lockdep class set to the fs tree. So when we attempt to lock that extent buffer through a relocation tree we have to reset the lockdep class to the class for a relocation tree, since a relocation tree has extent buffers that used to belong to a fs tree and may currently be already loaded (we swap extent buffers between the two trees at the end of replace_path()). However we are missing calls to btrfs_maybe_reset_lockdep_class() to reset the lockdep class at ctree.c:read_block_for_search() before we read lock an extent buffer, just like we did for btrfs_search_slot() in commit b40130b ("btrfs: fix lockdep splat with reloc root extent buffers"). So add the missing btrfs_maybe_reset_lockdep_class() calls before the attempts to read lock an extent buffer at ctree.c:read_block_for_search(). The lockdep splat was reported by syzbot and it looks like this: ====================================================== WARNING: possible circular locking dependency detected 6.13.0-rc5-syzkaller-00163-gab75170520d4 #0 Not tainted ------------------------------------------------------ syz.0.0/5335 is trying to acquire lock: ffff8880545dbc38 (btrfs-tree-01){++++}-{4:4}, at: btrfs_tree_read_lock_nested+0x2f/0x250 fs/btrfs/locking.c:146 but task is already holding lock: ffff8880545dba58 (btrfs-treloc-02/1){+.+.}-{4:4}, at: btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #2 (btrfs-treloc-02/1){+.+.}-{4:4}: reacquire_held_locks+0x3eb/0x690 kernel/locking/lockdep.c:5374 __lock_release kernel/locking/lockdep.c:5563 [inline] lock_release+0x396/0xa30 kernel/locking/lockdep.c:5870 up_write+0x79/0x590 kernel/locking/rwsem.c:1629 btrfs_force_cow_block+0x14b3/0x1fd0 fs/btrfs/ctree.c:660 btrfs_cow_block+0x371/0x830 fs/btrfs/ctree.c:755 btrfs_search_slot+0xc01/0x3180 fs/btrfs/ctree.c:2153 replace_path+0x1243/0x2740 fs/btrfs/relocation.c:1224 merge_reloc_root+0xc46/0x1ad0 fs/btrfs/relocation.c:1692 merge_reloc_roots+0x3b3/0x980 fs/btrfs/relocation.c:1942 relocate_block_group+0xb0a/0xd40 fs/btrfs/relocation.c:3754 btrfs_relocate_block_group+0x77d/0xd90 fs/btrfs/relocation.c:4087 btrfs_relocate_chunk+0x12c/0x3b0 fs/btrfs/volumes.c:3494 __btrfs_balance+0x1b0f/0x26b0 fs/btrfs/volumes.c:4278 btrfs_balance+0xbdc/0x10c0 fs/btrfs/volumes.c:4655 btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3670 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl+0xf5/0x170 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #1 (btrfs-tree-01/1){+.+.}-{4:4}: lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5849 down_write_nested+0xa2/0x220 kernel/locking/rwsem.c:1693 btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 btrfs_init_new_buffer fs/btrfs/extent-tree.c:5052 [inline] btrfs_alloc_tree_block+0x41c/0x1440 fs/btrfs/extent-tree.c:5132 btrfs_force_cow_block+0x526/0x1fd0 fs/btrfs/ctree.c:573 btrfs_cow_block+0x371/0x830 fs/btrfs/ctree.c:755 btrfs_search_slot+0xc01/0x3180 fs/btrfs/ctree.c:2153 btrfs_insert_empty_items+0x9c/0x1a0 fs/btrfs/ctree.c:4351 btrfs_insert_empty_item fs/btrfs/ctree.h:688 [inline] btrfs_insert_inode_ref+0x2bb/0xf80 fs/btrfs/inode-item.c:330 btrfs_rename_exchange fs/btrfs/inode.c:7990 [inline] btrfs_rename2+0xcb7/0x2b90 fs/btrfs/inode.c:8374 vfs_rename+0xbdb/0xf00 fs/namei.c:5067 do_renameat2+0xd94/0x13f0 fs/namei.c:5224 __do_sys_renameat2 fs/namei.c:5258 [inline] __se_sys_renameat2 fs/namei.c:5255 [inline] __x64_sys_renameat2+0xce/0xe0 fs/namei.c:5255 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f -> #0 (btrfs-tree-01){++++}-{4:4}: check_prev_add kernel/locking/lockdep.c:3161 [inline] check_prevs_add kernel/locking/lockdep.c:3280 [inline] validate_chain+0x18ef/0x5920 kernel/locking/lockdep.c:3904 __lock_acquire+0x1397/0x2100 kernel/locking/lockdep.c:5226 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5849 down_read_nested+0xb5/0xa50 kernel/locking/rwsem.c:1649 btrfs_tree_read_lock_nested+0x2f/0x250 fs/btrfs/locking.c:146 btrfs_tree_read_lock fs/btrfs/locking.h:188 [inline] read_block_for_search+0x718/0xbb0 fs/btrfs/ctree.c:1610 btrfs_search_slot+0x1274/0x3180 fs/btrfs/ctree.c:2237 replace_path+0x1243/0x2740 fs/btrfs/relocation.c:1224 merge_reloc_root+0xc46/0x1ad0 fs/btrfs/relocation.c:1692 merge_reloc_roots+0x3b3/0x980 fs/btrfs/relocation.c:1942 relocate_block_group+0xb0a/0xd40 fs/btrfs/relocation.c:3754 btrfs_relocate_block_group+0x77d/0xd90 fs/btrfs/relocation.c:4087 btrfs_relocate_chunk+0x12c/0x3b0 fs/btrfs/volumes.c:3494 __btrfs_balance+0x1b0f/0x26b0 fs/btrfs/volumes.c:4278 btrfs_balance+0xbdc/0x10c0 fs/btrfs/volumes.c:4655 btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3670 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl+0xf5/0x170 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f other info that might help us debug this: Chain exists of: btrfs-tree-01 --> btrfs-tree-01/1 --> btrfs-treloc-02/1 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(btrfs-treloc-02/1); lock(btrfs-tree-01/1); lock(btrfs-treloc-02/1); rlock(btrfs-tree-01); *** DEADLOCK *** 8 locks held by syz.0.0/5335: #0: ffff88801e3ae420 (sb_writers#13){.+.+}-{0:0}, at: mnt_want_write_file+0x5e/0x200 fs/namespace.c:559 #1: ffff888052c760d0 (&fs_info->reclaim_bgs_lock){+.+.}-{4:4}, at: __btrfs_balance+0x4c2/0x26b0 fs/btrfs/volumes.c:4183 #2: ffff888052c74850 (&fs_info->cleaner_mutex){+.+.}-{4:4}, at: btrfs_relocate_block_group+0x775/0xd90 fs/btrfs/relocation.c:4086 #3: ffff88801e3ae610 (sb_internal#2){.+.+}-{0:0}, at: merge_reloc_root+0xf11/0x1ad0 fs/btrfs/relocation.c:1659 #4: ffff888052c76470 (btrfs_trans_num_writers){++++}-{0:0}, at: join_transaction+0x405/0xda0 fs/btrfs/transaction.c:288 #5: ffff888052c76498 (btrfs_trans_num_extwriters){++++}-{0:0}, at: join_transaction+0x405/0xda0 fs/btrfs/transaction.c:288 #6: ffff8880545db878 (btrfs-tree-01/1){+.+.}-{4:4}, at: btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 #7: ffff8880545dba58 (btrfs-treloc-02/1){+.+.}-{4:4}, at: btrfs_tree_lock_nested+0x2f/0x250 fs/btrfs/locking.c:189 stack backtrace: CPU: 0 UID: 0 PID: 5335 Comm: syz.0.0 Not tainted 6.13.0-rc5-syzkaller-00163-gab75170520d4 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:94 [inline] dump_stack_lvl+0x241/0x360 lib/dump_stack.c:120 print_circular_bug+0x13a/0x1b0 kernel/locking/lockdep.c:2074 check_noncircular+0x36a/0x4a0 kernel/locking/lockdep.c:2206 check_prev_add kernel/locking/lockdep.c:3161 [inline] check_prevs_add kernel/locking/lockdep.c:3280 [inline] validate_chain+0x18ef/0x5920 kernel/locking/lockdep.c:3904 __lock_acquire+0x1397/0x2100 kernel/locking/lockdep.c:5226 lock_acquire+0x1ed/0x550 kernel/locking/lockdep.c:5849 down_read_nested+0xb5/0xa50 kernel/locking/rwsem.c:1649 btrfs_tree_read_lock_nested+0x2f/0x250 fs/btrfs/locking.c:146 btrfs_tree_read_lock fs/btrfs/locking.h:188 [inline] read_block_for_search+0x718/0xbb0 fs/btrfs/ctree.c:1610 btrfs_search_slot+0x1274/0x3180 fs/btrfs/ctree.c:2237 replace_path+0x1243/0x2740 fs/btrfs/relocation.c:1224 merge_reloc_root+0xc46/0x1ad0 fs/btrfs/relocation.c:1692 merge_reloc_roots+0x3b3/0x980 fs/btrfs/relocation.c:1942 relocate_block_group+0xb0a/0xd40 fs/btrfs/relocation.c:3754 btrfs_relocate_block_group+0x77d/0xd90 fs/btrfs/relocation.c:4087 btrfs_relocate_chunk+0x12c/0x3b0 fs/btrfs/volumes.c:3494 __btrfs_balance+0x1b0f/0x26b0 fs/btrfs/volumes.c:4278 btrfs_balance+0xbdc/0x10c0 fs/btrfs/volumes.c:4655 btrfs_ioctl_balance+0x493/0x7c0 fs/btrfs/ioctl.c:3670 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:906 [inline] __se_sys_ioctl+0xf5/0x170 fs/ioctl.c:892 do_syscall_x64 arch/x86/entry/common.c:52 [inline] do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83 entry_SYSCALL_64_after_hwframe+0x77/0x7f RIP: 0033:0x7f1ac6985d29 Code: ff ff c3 (...) RSP: 002b:00007f1ac63fe038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f1ac6b76160 RCX: 00007f1ac6985d29 RDX: 0000000020000180 RSI: 00000000c4009420 RDI: 0000000000000007 RBP: 00007f1ac6a01b08 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000001 R14: 00007f1ac6b76160 R15: 00007fffda145a88 </TASK> Reported-by: syzbot+63913e558c084f7f8fdc@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/677b3014.050a0220.3b53b0.0064.GAE@google.com/ Fixes: 9978599 ("btrfs: reduce lock contention when eb cache miss for btree search") Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>

We have several places across the kernel where we want to access another task's syscall arguments, such as ptrace(2), seccomp(2), etc., by making a call to syscall_get_arguments(). This works for register arguments right away by accessing the task's `regs' member of `struct pt_regs', however for stack arguments seen with 32-bit/o32 kernels things are more complicated. Technically they ought to be obtained from the user stack with calls to an access_remote_vm(), but we have an easier way available already. So as to be able to access syscall stack arguments as regular function arguments following the MIPS calling convention we copy them over from the user stack to the kernel stack in arch/mips/kernel/scall32-o32.S, in handle_sys(), to the current stack frame's outgoing argument space at the top of the stack, which is where the handler called expects to see its incoming arguments. This area is also pointed at by the `pt_regs' pointer obtained by task_pt_regs(). Make the o32 stack argument space a proper member of `struct pt_regs' then, by renaming the existing member from `pad0' to `args' and using generated offsets to access the space. No functional change though. With the change in place the o32 kernel stack frame layout at the entry to a syscall handler invoked by handle_sys() is therefore as follows: $sp + 68 -> | ... | <- pt_regs.regs[9] +---------------------+ $sp + 64 -> | $t0 | <- pt_regs.regs[8] +---------------------+ $sp + 60 -> | $a3/argument #4 | <- pt_regs.regs[7] +---------------------+ $sp + 56 -> | $a2/argument #3 | <- pt_regs.regs[6] +---------------------+ $sp + 52 -> | $a1/argument #2 | <- pt_regs.regs[5] +---------------------+ $sp + 48 -> | $a0/argument #1 | <- pt_regs.regs[4] +---------------------+ $sp + 44 -> | $v1 | <- pt_regs.regs[3] +---------------------+ $sp + 40 -> | $v0 | <- pt_regs.regs[2] +---------------------+ $sp + 36 -> | $at | <- pt_regs.regs[1] +---------------------+ $sp + 32 -> | $zero | <- pt_regs.regs[0] +---------------------+ $sp + 28 -> | stack argument torvalds#8 | <- pt_regs.args[7] +---------------------+ $sp + 24 -> | stack argument #7 | <- pt_regs.args[6] +---------------------+ $sp + 20 -> | stack argument #6 | <- pt_regs.args[5] +---------------------+ $sp + 16 -> | stack argument #5 | <- pt_regs.args[4] +---------------------+ $sp + 12 -> | psABI space for $a3 | <- pt_regs.args[3] +---------------------+ $sp + 8 -> | psABI space for $a2 | <- pt_regs.args[2] +---------------------+ $sp + 4 -> | psABI space for $a1 | <- pt_regs.args[1] +---------------------+ $sp + 0 -> | psABI space for $a0 | <- pt_regs.args[0] +---------------------+ holding user data received and with the first 4 frame slots reserved by the psABI for the compiler to spill the incoming arguments from $a0-$a3 registers (which it sometimes does according to its needs) and the next 4 frame slots designated by the psABI for any stack function arguments that follow. This data is also available for other tasks to peek/poke at as reqired and where permitted. Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>

Use raw_spinlock in order to fix spurious messages about invalid context when spinlock debugging is enabled. The lock is only used to serialize register access. [ 4.239592] ============================= [ 4.239595] [ BUG: Invalid wait context ] [ 4.239599] 6.13.0-rc7-arm64-renesas-05496-gd088502a519f torvalds#35 Not tainted [ 4.239603] ----------------------------- [ 4.239606] kworker/u8:5/76 is trying to lock: [ 4.239609] ffff0000091898a0 (&p->lock){....}-{3:3}, at: gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.239641] other info that might help us debug this: [ 4.239643] context-{5:5} [ 4.239646] 5 locks held by kworker/u8:5/76: [ 4.239651] #0: ffff0000080fb148 ((wq_completion)async){+.+.}-{0:0}, at: process_one_work+0x190/0x62c [ 4.250180] OF: /soc/sound@ec500000/ports/port@0/endpoint: Read of boolean property 'frame-master' with a value. [ 4.254094] #1: ffff80008299bd80 ((work_completion)(&entry->work)){+.+.}-{0:0}, at: process_one_work+0x1b8/0x62c [ 4.254109] #2: ffff00000920c8f8 [ 4.258345] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'bitclock-master' with a value. [ 4.264803] (&dev->mutex){....}-{4:4}, at: __device_attach_async_helper+0x3c/0xdc [ 4.264820] #3: ffff00000a50ca40 (request_class#2){+.+.}-{4:4}, at: __setup_irq+0xa0/0x690 [ 4.264840] #4: [ 4.268872] OF: /soc/sound@ec500000/ports/port@1/endpoint: Read of boolean property 'frame-master' with a value. [ 4.273275] ffff00000a50c8c8 (lock_class){....}-{2:2}, at: __setup_irq+0xc4/0x690 [ 4.296130] renesas_sdhi_internal_dmac ee100000.mmc: mmc1 base at 0x00000000ee100000, max clock rate 200 MHz [ 4.304082] stack backtrace: [ 4.304086] CPU: 1 UID: 0 PID: 76 Comm: kworker/u8:5 Not tainted 6.13.0-rc7-arm64-renesas-05496-gd088502a519f torvalds#35 [ 4.304092] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT) [ 4.304097] Workqueue: async async_run_entry_fn [ 4.304106] Call trace: [ 4.304110] show_stack+0x14/0x20 (C) [ 4.304122] dump_stack_lvl+0x6c/0x90 [ 4.304131] dump_stack+0x14/0x1c [ 4.304138] __lock_acquire+0xdfc/0x1584 [ 4.426274] lock_acquire+0x1c4/0x33c [ 4.429942] _raw_spin_lock_irqsave+0x5c/0x80 [ 4.434307] gpio_rcar_config_interrupt_input_mode+0x34/0x164 [ 4.440061] gpio_rcar_irq_set_type+0xd4/0xd8 [ 4.444422] __irq_set_trigger+0x5c/0x178 [ 4.448435] __setup_irq+0x2e4/0x690 [ 4.452012] request_threaded_irq+0xc4/0x190 [ 4.456285] devm_request_threaded_irq+0x7c/0xf4 [ 4.459398] ata1: link resume succeeded after 1 retries [ 4.460902] mmc_gpiod_request_cd_irq+0x68/0xe0 [ 4.470660] mmc_start_host+0x50/0xac [ 4.474327] mmc_add_host+0x80/0xe4 [ 4.477817] tmio_mmc_host_probe+0x2b0/0x440 [ 4.482094] renesas_sdhi_probe+0x488/0x6f4 [ 4.486281] renesas_sdhi_internal_dmac_probe+0x60/0x78 [ 4.491509] platform_probe+0x64/0xd8 [ 4.495178] really_probe+0xb8/0x2a8 [ 4.498756] __driver_probe_device+0x74/0x118 [ 4.503116] driver_probe_device+0x3c/0x154 [ 4.507303] __device_attach_driver+0xd4/0x160 [ 4.511750] bus_for_each_drv+0x84/0xe0 [ 4.515588] __device_attach_async_helper+0xb0/0xdc [ 4.520470] async_run_entry_fn+0x30/0xd8 [ 4.524481] process_one_work+0x210/0x62c [ 4.528494] worker_thread+0x1ac/0x340 [ 4.532245] kthread+0x10c/0x110 [ 4.535476] ret_from_fork+0x10/0x20 Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20250121135833.3769310-1-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

…/kernel/git/kvmarm/kvmarm into HEAD KVM/arm64 fixes for 6.14, take #4 - Fix a couple of bugs affecting pKVM's PSCI relay implementation when running in the hVHE mode, resulting in the host being entered with the MMU in an unknown state, and EL2 being in the wrong mode.

…cal section A circular lock dependency splat has been seen involving down_trylock(): ====================================================== WARNING: possible circular locking dependency detected 6.12.0-41.el10.s390x+debug ------------------------------------------------------ dd/32479 is trying to acquire lock: 0015a20accd0d4f8 ((console_sem).lock){-.-.}-{2:2}, at: down_trylock+0x26/0x90 but task is already holding lock: 000000017e461698 (&zone->lock){-.-.}-{2:2}, at: rmqueue_bulk+0xac/0x8f0 the existing dependency chain (in reverse order) is: -> #4 (&zone->lock){-.-.}-{2:2}: -> #3 (hrtimer_bases.lock){-.-.}-{2:2}: -> #2 (&rq->__lock){-.-.}-{2:2}: -> #1 (&p->pi_lock){-.-.}-{2:2}: -> #0 ((console_sem).lock){-.-.}-{2:2}: The console_sem -> pi_lock dependency is due to calling try_to_wake_up() while holding the console_sem raw_spinlock. This dependency can be broken by using wake_q to do the wakeup instead of calling try_to_wake_up() under the console_sem lock. This will also make the semaphore's raw_spinlock become a terminal lock without taking any further locks underneath it. The hrtimer_bases.lock is a raw_spinlock while zone->lock is a spinlock. The hrtimer_bases.lock -> zone->lock dependency happens via the debug_objects_fill_pool() helper function in the debugobjects code. -> #4 (&zone->lock){-.-.}-{2:2}: __lock_acquire+0xe86/0x1cc0 lock_acquire.part.0+0x258/0x630 lock_acquire+0xb8/0xe0 _raw_spin_lock_irqsave+0xb4/0x120 rmqueue_bulk+0xac/0x8f0 __rmqueue_pcplist+0x580/0x830 rmqueue_pcplist+0xfc/0x470 rmqueue.isra.0+0xdec/0x11b0 get_page_from_freelist+0x2ee/0xeb0 __alloc_pages_noprof+0x2c2/0x520 alloc_pages_mpol_noprof+0x1fc/0x4d0 alloc_pages_noprof+0x8c/0xe0 allocate_slab+0x320/0x460 ___slab_alloc+0xa58/0x12b0 __slab_alloc.isra.0+0x42/0x60 kmem_cache_alloc_noprof+0x304/0x350 fill_pool+0xf6/0x450 debug_object_activate+0xfe/0x360 enqueue_hrtimer+0x34/0x190 __run_hrtimer+0x3c8/0x4c0 __hrtimer_run_queues+0x1b2/0x260 hrtimer_interrupt+0x316/0x760 do_IRQ+0x9a/0xe0 do_irq_async+0xf6/0x160 Normally a raw_spinlock to spinlock dependency is not legitimate and will be warned if CONFIG_PROVE_RAW_LOCK_NESTING is enabled, but debug_objects_fill_pool() is an exception as it explicitly allows this dependency for non-PREEMPT_RT kernel without causing PROVE_RAW_LOCK_NESTING lockdep splat. As a result, this dependency is legitimate and not a bug. Anyway, semaphore is the only locking primitive left that is still using try_to_wake_up() to do wakeup inside critical section, all the other locking primitives had been migrated to use wake_q to do wakeup outside of the critical section. It is also possible that there are other circular locking dependencies involving printk/console_sem or other existing/new semaphores lurking somewhere which may show up in the future. Let just do the migration now to wake_q to avoid headache like this. Reported-by: yzbot+ed801a886dfdbfe7136d@syzkaller.appspotmail.com Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Boqun Feng <boqun.feng@gmail.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/20250307232717.1759087-3-boqun.feng@gmail.com

perf test 11 hwmon fails on s390 with this error # ./perf test -Fv 11 --- start --- ---- end ---- 11.1: Basic parsing test : Ok --- start --- Testing 'temp_test_hwmon_event1' Using CPUID IBM,3931,704,A01,3.7,002f temp_test_hwmon_event1 -> hwmon_a_test_hwmon_pmu/temp_test_hwmon_event1/ FAILED tests/hwmon_pmu.c:189 Unexpected config for 'temp_test_hwmon_event1', 292470092988416 != 655361 ---- end ---- 11.2: Parsing without PMU name : FAILED! --- start --- Testing 'hwmon_a_test_hwmon_pmu/temp_test_hwmon_event1/' FAILED tests/hwmon_pmu.c:189 Unexpected config for 'hwmon_a_test_hwmon_pmu/temp_test_hwmon_event1/', 292470092988416 != 655361 ---- end ---- 11.3: Parsing with PMU name : FAILED! # The root cause is in member test_event::config which is initialized to 0xA0001 or 655361. During event parsing a long list event parsing functions are called and end up with this gdb call stack: #0 hwmon_pmu__config_term (hwm=0x168dfd0, attr=0x3ffffff5ee8, term=0x168db60, err=0x3ffffff81c8) at util/hwmon_pmu.c:623 #1 hwmon_pmu__config_terms (pmu=0x168dfd0, attr=0x3ffffff5ee8, terms=0x3ffffff5ea8, err=0x3ffffff81c8) at util/hwmon_pmu.c:662 #2 0x00000000012f870c in perf_pmu__config_terms (pmu=0x168dfd0, attr=0x3ffffff5ee8, terms=0x3ffffff5ea8, zero=false, apply_hardcoded=false, err=0x3ffffff81c8) at util/pmu.c:1519 #3 0x00000000012f88a4 in perf_pmu__config (pmu=0x168dfd0, attr=0x3ffffff5ee8, head_terms=0x3ffffff5ea8, apply_hardcoded=false, err=0x3ffffff81c8) at util/pmu.c:1545 #4 0x00000000012680c4 in parse_events_add_pmu (parse_state=0x3ffffff7fb8, list=0x168dc00, pmu=0x168dfd0, const_parsed_terms=0x3ffffff6090, auto_merge_stats=true, alternate_hw_config=10) at util/parse-events.c:1508 #5 0x00000000012684c6 in parse_events_multi_pmu_add (parse_state=0x3ffffff7fb8, event_name=0x168ec10 "temp_test_hwmon_event1", hw_config=10, const_parsed_terms=0x0, listp=0x3ffffff6230, loc_=0x3ffffff70e0) at util/parse-events.c:1592 #6 0x00000000012f0e4e in parse_events_parse (_parse_state=0x3ffffff7fb8, scanner=0x16878c0) at util/parse-events.y:293 #7 0x00000000012695a0 in parse_events__scanner (str=0x3ffffff81d8 "temp_test_hwmon_event1", input=0x0, parse_state=0x3ffffff7fb8) at util/parse-events.c:1867 torvalds#8 0x000000000126a1e8 in __parse_events (evlist=0x168b580, str=0x3ffffff81d8 "temp_test_hwmon_event1", pmu_filter=0x0, err=0x3ffffff81c8, fake_pmu=false, warn_if_reordered=true, fake_tp=false) at util/parse-events.c:2136 torvalds#9 0x00000000011e36aa in parse_events (evlist=0x168b580, str=0x3ffffff81d8 "temp_test_hwmon_event1", err=0x3ffffff81c8) at /root/linux/tools/perf/util/parse-events.h:41 torvalds#10 0x00000000011e3e64 in do_test (i=0, with_pmu=false, with_alias=false) at tests/hwmon_pmu.c:164 torvalds#11 0x00000000011e422c in test__hwmon_pmu (with_pmu=false) at tests/hwmon_pmu.c:219 #12 0x00000000011e431c in test__hwmon_pmu_without_pmu (test=0x1610368 <suite.hwmon_pmu>, subtest=1) at tests/hwmon_pmu.c:23 where the attr::config is set to value 292470092988416 or 0x10a0000000000 in line 625 of file ./util/hwmon_pmu.c: attr->config = key.type_and_num; However member key::type_and_num is defined as union and bit field: union hwmon_pmu_event_key { long type_and_num; struct { int num :16; enum hwmon_type type :8; }; }; s390 is big endian and Intel is little endian architecture. The events for the hwmon dummy pmu have num = 1 or num = 2 and type is set to HWMON_TYPE_TEMP (which is 10). On s390 this assignes member key::type_and_num the value of 0x10a0000000000 (which is 292470092988416) as shown in above trace output. Fix this and export the structure/union hwmon_pmu_event_key so the test shares the same implementation as the event parsing functions for union and bit fields. This should avoid endianess issues on all platforms. Output after: # ./perf test -F 11 11.1: Basic parsing test : Ok 11.2: Parsing without PMU name : Ok 11.3: Parsing with PMU name : Ok # Fixes: 531ee0f ("perf test: Add hwmon "PMU" test") Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Ian Rogers <irogers@google.com> Link: https://lore.kernel.org/r/20250131112400.568975-1-tmricht@linux.ibm.com Signed-off-by: Namhyung Kim <namhyung@kernel.org>

Ian told me that there are many memory leaks in the hierarchy mode. I can easily reproduce it with the follwing command. $ make DEBUG=1 EXTRA_CFLAGS=-fsanitize=leak $ perf record --latency -g -- ./perf test -w thloop $ perf report -H --stdio ... Indirect leak of 168 byte(s) in 21 object(s) allocated from: #0 0x7f3414c16c65 in malloc ../../../../src/libsanitizer/lsan/lsan_interceptors.cpp:75 #1 0x55ed3602346e in map__get util/map.h:189 #2 0x55ed36024cc4 in hist_entry__init util/hist.c:476 #3 0x55ed36025208 in hist_entry__new util/hist.c:588 #4 0x55ed36027c05 in hierarchy_insert_entry util/hist.c:1587 #5 0x55ed36027e2e in hists__hierarchy_insert_entry util/hist.c:1638 #6 0x55ed36027fa4 in hists__collapse_insert_entry util/hist.c:1685 #7 0x55ed360283e8 in hists__collapse_resort util/hist.c:1776 torvalds#8 0x55ed35de0323 in report__collapse_hists /home/namhyung/project/linux/tools/perf/builtin-report.c:735 torvalds#9 0x55ed35de15b4 in __cmd_report /home/namhyung/project/linux/tools/perf/builtin-report.c:1119 torvalds#10 0x55ed35de43dc in cmd_report /home/namhyung/project/linux/tools/perf/builtin-report.c:1867 torvalds#11 0x55ed35e66767 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:351 #12 0x55ed35e66a0e in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:404 #13 0x55ed35e66b67 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:448 torvalds#14 0x55ed35e66eb0 in main /home/namhyung/project/linux/tools/perf/perf.c:556 #15 0x7f340ac33d67 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 ... $ perf report -H --stdio 2>&1 | grep -c '^Indirect leak' 93 I found that hist_entry__delete() missed to release child entries in the hierarchy tree (hroot_{in,out}). It needs to iterate the child entries and call hist_entry__delete() recursively. After this change: $ perf report -H --stdio 2>&1 | grep -c '^Indirect leak' 0 Reported-by: Ian Rogers <irogers@google.com> Tested-by Thomas Falcon <thomas.falcon@intel.com> Reviewed-by: Ian Rogers <irogers@google.com> Link: https://lore.kernel.org/r/20250307061250.320849-2-namhyung@kernel.org Signed-off-by: Namhyung Kim <namhyung@kernel.org>

The env.pmu_mapping can be leaked when it reads data from a pipe on AMD. For a pipe data, it reads the header data including pmu_mapping from PERF_RECORD_HEADER_FEATURE runtime. But it's already set in: perf_session__new() __perf_session__new() evlist__init_trace_event_sample_raw() evlist__has_amd_ibs() perf_env__nr_pmu_mappings() Then it'll overwrite that when it processes the HEADER_FEATURE record. Here's a report from address sanitizer. Direct leak of 2689 byte(s) in 1 object(s) allocated from: #0 0x7fed8f814596 in realloc ../../../../src/libsanitizer/lsan/lsan_interceptors.cpp:98 #1 0x5595a7d416b1 in strbuf_grow util/strbuf.c:64 #2 0x5595a7d414ef in strbuf_init util/strbuf.c:25 #3 0x5595a7d0f4b7 in perf_env__read_pmu_mappings util/env.c:362 #4 0x5595a7d12ab7 in perf_env__nr_pmu_mappings util/env.c:517 #5 0x5595a7d89d2f in evlist__has_amd_ibs util/amd-sample-raw.c:315 #6 0x5595a7d87fb2 in evlist__init_trace_event_sample_raw util/sample-raw.c:23 #7 0x5595a7d7f893 in __perf_session__new util/session.c:179 torvalds#8 0x5595a7b79572 in perf_session__new util/session.h:115 torvalds#9 0x5595a7b7e9dc in cmd_report builtin-report.c:1603 torvalds#10 0x5595a7c019eb in run_builtin perf.c:351 torvalds#11 0x5595a7c01c92 in handle_internal_command perf.c:404 #12 0x5595a7c01deb in run_argv perf.c:448 #13 0x5595a7c02134 in main perf.c:556 torvalds#14 0x7fed85833d67 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 Let's free the existing pmu_mapping data if any. Cc: Ravi Bangoria <ravi.bangoria@amd.com> Link: https://lore.kernel.org/r/20250311000416.817631-1-namhyung@kernel.org Signed-off-by: Namhyung Kim <namhyung@kernel.org>

When a bio with REQ_PREFLUSH is submitted to dm, __send_empty_flush() generates a flush_bio with REQ_OP_WRITE | REQ_PREFLUSH | REQ_SYNC, which causes the flush_bio to be throttled by wbt_wait(). An example from v5.4, similar problem also exists in upstream: crash> bt 2091206 PID: 2091206 TASK: ffff2050df92a300 CPU: 109 COMMAND: "kworker/u260:0" #0 [ffff800084a2f7f0] __switch_to at ffff80004008aeb8 #1 [ffff800084a2f820] __schedule at ffff800040bfa0c4 #2 [ffff800084a2f880] schedule at ffff800040bfa4b4 #3 [ffff800084a2f8a0] io_schedule at ffff800040bfa9c4 #4 [ffff800084a2f8c0] rq_qos_wait at ffff8000405925bc #5 [ffff800084a2f940] wbt_wait at ffff8000405bb3a0 #6 [ffff800084a2f9a0] __rq_qos_throttle at ffff800040592254 #7 [ffff800084a2f9c0] blk_mq_make_request at ffff80004057cf38 torvalds#8 [ffff800084a2fa60] generic_make_request at ffff800040570138 torvalds#9 [ffff800084a2fae0] submit_bio at ffff8000405703b4 torvalds#10 [ffff800084a2fb50] xlog_write_iclog at ffff800001280834 [xfs] torvalds#11 [ffff800084a2fbb0] xlog_sync at ffff800001280c3c [xfs] #12 [ffff800084a2fbf0] xlog_state_release_iclog at ffff800001280df4 [xfs] #13 [ffff800084a2fc10] xlog_write at ffff80000128203c [xfs] torvalds#14 [ffff800084a2fcd0] xlog_cil_push at ffff8000012846dc [xfs] #15 [ffff800084a2fda0] xlog_cil_push_work at ffff800001284a2c [xfs] #16 [ffff800084a2fdb0] process_one_work at ffff800040111d08 #17 [ffff800084a2fe00] worker_thread at ffff8000401121cc #18 [ffff800084a2fe70] kthread at ffff800040118de4 After commit 2def284 ("xfs: don't allow log IO to be throttled"), the metadata submitted by xlog_write_iclog() should not be throttled. But due to the existence of the dm layer, throttling flush_bio indirectly causes the metadata bio to be throttled. Fix this by conditionally adding REQ_IDLE to flush_bio.bi_opf, which makes wbt_should_throttle() return false to avoid wbt_wait(). Signed-off-by: Jinliang Zheng <alexjlzheng@tencent.com> Reviewed-by: Tianxiang Peng <txpeng@tencent.com> Reviewed-by: Hao Peng <flyingpeng@tencent.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>

v2: - Created a single error handling unlock and exit in veth_pool_store - Greatly expanded commit message with previous explanatory-only text Summary: Use rtnl_mutex to synchronize veth_pool_store with itself, ibmveth_close and ibmveth_open, preventing multiple calls in a row to napi_disable. Background: Two (or more) threads could call veth_pool_store through writing to /sys/devices/vio/30000002/pool*/*. You can do this easily with a little shell script. This causes a hang. I configured LOCKDEP, compiled ibmveth.c with DEBUG, and built a new kernel. I ran this test again and saw: Setting pool0/active to 0 Setting pool1/active to 1 [ 73.911067][ T4365] ibmveth 30000002 eth0: close starting Setting pool1/active to 1 Setting pool1/active to 0 [ 73.911367][ T4366] ibmveth 30000002 eth0: close starting [ 73.916056][ T4365] ibmveth 30000002 eth0: close complete [ 73.916064][ T4365] ibmveth 30000002 eth0: open starting [ 110.808564][ T712] systemd-journald[712]: Sent WATCHDOG=1 notification. [ 230.808495][ T712] systemd-journald[712]: Sent WATCHDOG=1 notification. [ 243.683786][ T123] INFO: task stress.sh:4365 blocked for more than 122 seconds. [ 243.683827][ T123] Not tainted 6.14.0-01103-g2df0c02dab82-dirty torvalds#8 [ 243.683833][ T123] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 243.683838][ T123] task:stress.sh state:D stack:28096 pid:4365 tgid:4365 ppid:4364 task_flags:0x400040 flags:0x00042000 [ 243.683852][ T123] Call Trace: [ 243.683857][ T123] [c00000000c38f690] [0000000000000001] 0x1 (unreliable) [ 243.683868][ T123] [c00000000c38f840] [c00000000001f908] __switch_to+0x318/0x4e0 [ 243.683878][ T123] [c00000000c38f8a0] [c000000001549a70] __schedule+0x500/0x12a0 [ 243.683888][ T123] [c00000000c38f9a0] [c00000000154a878] schedule+0x68/0x210 [ 243.683896][ T123] [c00000000c38f9d0] [c00000000154ac80] schedule_preempt_disabled+0x30/0x50 [ 243.683904][ T123] [c00000000c38fa00] [c00000000154dbb0] __mutex_lock+0x730/0x10f0 [ 243.683913][ T123] [c00000000c38fb10] [c000000001154d40] napi_enable+0x30/0x60 [ 243.683921][ T123] [c00000000c38fb40] [c000000000f4ae94] ibmveth_open+0x68/0x5dc [ 243.683928][ T123] [c00000000c38fbe0] [c000000000f4aa20] veth_pool_store+0x220/0x270 [ 243.683936][ T123] [c00000000c38fc70] [c000000000826278] sysfs_kf_write+0x68/0xb0 [ 243.683944][ T123] [c00000000c38fcb0] [c0000000008240b8] kernfs_fop_write_iter+0x198/0x2d0 [ 243.683951][ T123] [c00000000c38fd00] [c00000000071b9ac] vfs_write+0x34c/0x650 [ 243.683958][ T123] [c00000000c38fdc0] [c00000000071bea8] ksys_write+0x88/0x150 [ 243.683966][ T123] [c00000000c38fe10] [c0000000000317f4] system_call_exception+0x124/0x340 [ 243.683973][ T123] [c00000000c38fe50] [c00000000000d05c] system_call_vectored_common+0x15c/0x2ec ... [ 243.684087][ T123] Showing all locks held in the system: [ 243.684095][ T123] 1 lock held by khungtaskd/123: [ 243.684099][ T123] #0: c00000000278e370 (rcu_read_lock){....}-{1:2}, at: debug_show_all_locks+0x50/0x248 [ 243.684114][ T123] 4 locks held by stress.sh/4365: [ 243.684119][ T123] #0: c00000003a4cd3f8 (sb_writers#3){.+.+}-{0:0}, at: ksys_write+0x88/0x150 [ 243.684132][ T123] #1: c000000041aea888 (&of->mutex#2){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x154/0x2d0 [ 243.684143][ T123] #2: c0000000366fb9a8 (kn->active#64){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x160/0x2d0 [ 243.684155][ T123] #3: c000000035ff4cb8 (&dev->lock){+.+.}-{3:3}, at: napi_enable+0x30/0x60 [ 243.684166][ T123] 5 locks held by stress.sh/4366: [ 243.684170][ T123] #0: c00000003a4cd3f8 (sb_writers#3){.+.+}-{0:0}, at: ksys_write+0x88/0x150 [ 243.684183][ T123] #1: c00000000aee2288 (&of->mutex#2){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x154/0x2d0 [ 243.684194][ T123] #2: c0000000366f4ba8 (kn->active#64){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x160/0x2d0 [ 243.684205][ T123] #3: c000000035ff4cb8 (&dev->lock){+.+.}-{3:3}, at: napi_disable+0x30/0x60 [ 243.684216][ T123] #4: c0000003ff9bbf18 (&rq->__lock){-.-.}-{2:2}, at: __schedule+0x138/0x12a0 From the ibmveth debug, two threads are calling veth_pool_store, which calls ibmveth_close and ibmveth_open. Here's the sequence: T4365 T4366 ----------------- ----------------- --------- veth_pool_store veth_pool_store ibmveth_close ibmveth_close napi_disable napi_disable ibmveth_open napi_enable <- HANG ibmveth_close calls napi_disable at the top and ibmveth_open calls napi_enable at the top. https://docs.kernel.org/networking/napi.html]] says The control APIs are not idempotent. Control API calls are safe against concurrent use of datapath APIs but an incorrect sequence of control API calls may result in crashes, deadlocks, or race conditions. For example, calling napi_disable() multiple times in a row will deadlock. In the normal open and close paths, rtnl_mutex is acquired to prevent other callers. This is missing from veth_pool_store. Use rtnl_mutex in veth_pool_store fixes these hangs. Signed-off-by: Dave Marquardt <davemarq@linux.ibm.com> Fixes: 860f242 ("[PATCH] ibmveth change buffer pools dynamically") Reviewed-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250402154403.386744-1-davemarq@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There is a potential deadlock if we do report zones in an IO context, detailed in below lockdep report. When one process do a report zones and another process freezes the block device, the report zones side cannot allocate a tag because the freeze is already started. This can thus result in new block group creation to hang forever, blocking the write path. Thankfully, a new block group should be created on empty zones. So, reporting the zones is not necessary and we can set the write pointer = 0 and load the zone capacity from the block layer using bdev_zone_capacity() helper. ====================================================== WARNING: possible circular locking dependency detected 6.14.0-rc1 #252 Not tainted ------------------------------------------------------ modprobe/1110 is trying to acquire lock: ffff888100ac83e0 ((work_completion)(&(&wb->dwork)->work)){+.+.}-{0:0}, at: __flush_work+0x38f/0xb60 but task is already holding lock: ffff8881205b6f20 (&q->q_usage_counter(queue)#16){++++}-{0:0}, at: sd_remove+0x85/0x130 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (&q->q_usage_counter(queue)#16){++++}-{0:0}: blk_queue_enter+0x3d9/0x500 blk_mq_alloc_request+0x47d/0x8e0 scsi_execute_cmd+0x14f/0xb80 sd_zbc_do_report_zones+0x1c1/0x470 sd_zbc_report_zones+0x362/0xd60 blkdev_report_zones+0x1b1/0x2e0 btrfs_get_dev_zones+0x215/0x7e0 [btrfs] btrfs_load_block_group_zone_info+0x6d2/0x2c10 [btrfs] btrfs_make_block_group+0x36b/0x870 [btrfs] btrfs_create_chunk+0x147d/0x2320 [btrfs] btrfs_chunk_alloc+0x2ce/0xcf0 [btrfs] start_transaction+0xce6/0x1620 [btrfs] btrfs_uuid_scan_kthread+0x4ee/0x5b0 [btrfs] kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #2 (&fs_info->dev_replace.rwsem){++++}-{4:4}: down_read+0x9b/0x470 btrfs_map_block+0x2ce/0x2ce0 [btrfs] btrfs_submit_chunk+0x2d4/0x16c0 [btrfs] btrfs_submit_bbio+0x16/0x30 [btrfs] btree_write_cache_pages+0xb5a/0xf90 [btrfs] do_writepages+0x17f/0x7b0 __writeback_single_inode+0x114/0xb00 writeback_sb_inodes+0x52b/0xe00 wb_writeback+0x1a7/0x800 wb_workfn+0x12a/0xbd0 process_one_work+0x85a/0x1460 worker_thread+0x5e2/0xfc0 kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #1 (&fs_info->zoned_meta_io_lock){+.+.}-{4:4}: __mutex_lock+0x1aa/0x1360 btree_write_cache_pages+0x252/0xf90 [btrfs] do_writepages+0x17f/0x7b0 __writeback_single_inode+0x114/0xb00 writeback_sb_inodes+0x52b/0xe00 wb_writeback+0x1a7/0x800 wb_workfn+0x12a/0xbd0 process_one_work+0x85a/0x1460 worker_thread+0x5e2/0xfc0 kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #0 ((work_completion)(&(&wb->dwork)->work)){+.+.}-{0:0}: __lock_acquire+0x2f52/0x5ea0 lock_acquire+0x1b1/0x540 __flush_work+0x3ac/0xb60 wb_shutdown+0x15b/0x1f0 bdi_unregister+0x172/0x5b0 del_gendisk+0x841/0xa20 sd_remove+0x85/0x130 device_release_driver_internal+0x368/0x520 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 __scsi_remove_device+0x272/0x340 scsi_forget_host+0xf7/0x170 scsi_remove_host+0xd2/0x2a0 sdebug_driver_remove+0x52/0x2f0 [scsi_debug] device_release_driver_internal+0x368/0x520 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 device_unregister+0x13/0xa0 sdebug_do_remove_host+0x1fb/0x290 [scsi_debug] scsi_debug_exit+0x17/0x70 [scsi_debug] __do_sys_delete_module.isra.0+0x321/0x520 do_syscall_64+0x93/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e other info that might help us debug this: Chain exists of: (work_completion)(&(&wb->dwork)->work) --> &fs_info->dev_replace.rwsem --> &q->q_usage_counter(queue)#16 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&q->q_usage_counter(queue)#16); lock(&fs_info->dev_replace.rwsem); lock(&q->q_usage_counter(queue)#16); lock((work_completion)(&(&wb->dwork)->work)); *** DEADLOCK *** 5 locks held by modprobe/1110: #0: ffff88811f7bc108 (&dev->mutex){....}-{4:4}, at: device_release_driver_internal+0x8f/0x520 #1: ffff8881022ee0e0 (&shost->scan_mutex){+.+.}-{4:4}, at: scsi_remove_host+0x20/0x2a0 #2: ffff88811b4c4378 (&dev->mutex){....}-{4:4}, at: device_release_driver_internal+0x8f/0x520 #3: ffff8881205b6f20 (&q->q_usage_counter(queue)#16){++++}-{0:0}, at: sd_remove+0x85/0x130 #4: ffffffffa3284360 (rcu_read_lock){....}-{1:3}, at: __flush_work+0xda/0xb60 stack backtrace: CPU: 0 UID: 0 PID: 1110 Comm: modprobe Not tainted 6.14.0-rc1 #252 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x6a/0x90 print_circular_bug.cold+0x1e0/0x274 check_noncircular+0x306/0x3f0 ? __pfx_check_noncircular+0x10/0x10 ? mark_lock+0xf5/0x1650 ? __pfx_check_irq_usage+0x10/0x10 ? lockdep_lock+0xca/0x1c0 ? __pfx_lockdep_lock+0x10/0x10 __lock_acquire+0x2f52/0x5ea0 ? __pfx___lock_acquire+0x10/0x10 ? __pfx_mark_lock+0x10/0x10 lock_acquire+0x1b1/0x540 ? __flush_work+0x38f/0xb60 ? __pfx_lock_acquire+0x10/0x10 ? __pfx_lock_release+0x10/0x10 ? mark_held_locks+0x94/0xe0 ? __flush_work+0x38f/0xb60 __flush_work+0x3ac/0xb60 ? __flush_work+0x38f/0xb60 ? __pfx_mark_lock+0x10/0x10 ? __pfx___flush_work+0x10/0x10 ? __pfx_wq_barrier_func+0x10/0x10 ? __pfx___might_resched+0x10/0x10 ? mark_held_locks+0x94/0xe0 wb_shutdown+0x15b/0x1f0 bdi_unregister+0x172/0x5b0 ? __pfx_bdi_unregister+0x10/0x10 ? up_write+0x1ba/0x510 del_gendisk+0x841/0xa20 ? __pfx_del_gendisk+0x10/0x10 ? _raw_spin_unlock_irqrestore+0x35/0x60 ? __pm_runtime_resume+0x79/0x110 sd_remove+0x85/0x130 device_release_driver_internal+0x368/0x520 ? kobject_put+0x5d/0x4a0 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 ? __pfx_device_del+0x10/0x10 __scsi_remove_device+0x272/0x340 scsi_forget_host+0xf7/0x170 scsi_remove_host+0xd2/0x2a0 sdebug_driver_remove+0x52/0x2f0 [scsi_debug] ? kernfs_remove_by_name_ns+0xc0/0xf0 device_release_driver_internal+0x368/0x520 ? kobject_put+0x5d/0x4a0 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 ? __pfx_device_del+0x10/0x10 ? __pfx___mutex_unlock_slowpath+0x10/0x10 device_unregister+0x13/0xa0 sdebug_do_remove_host+0x1fb/0x290 [scsi_debug] scsi_debug_exit+0x17/0x70 [scsi_debug] __do_sys_delete_module.isra.0+0x321/0x520 ? __pfx___do_sys_delete_module.isra.0+0x10/0x10 ? __pfx_slab_free_after_rcu_debug+0x10/0x10 ? kasan_save_stack+0x2c/0x50 ? kasan_record_aux_stack+0xa3/0xb0 ? __call_rcu_common.constprop.0+0xc4/0xfb0 ? kmem_cache_free+0x3a0/0x590 ? __x64_sys_close+0x78/0xd0 do_syscall_64+0x93/0x180 ? lock_is_held_type+0xd5/0x130 ? __call_rcu_common.constprop.0+0x3c0/0xfb0 ? lockdep_hardirqs_on+0x78/0x100 ? __call_rcu_common.constprop.0+0x3c0/0xfb0 ? __pfx___call_rcu_common.constprop.0+0x10/0x10 ? kmem_cache_free+0x3a0/0x590 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? __pfx___x64_sys_openat+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f436712b68b RSP: 002b:00007ffe9f1a8658 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 RAX: ffffffffffffffda RBX: 00005559b367fd80 RCX: 00007f436712b68b RDX: 0000000000000000 RSI: 0000000000000800 RDI: 00005559b367fde8 RBP: 00007ffe9f1a8680 R08: 1999999999999999 R09: 0000000000000000 R10: 00007f43671a5fe0 R11: 0000000000000206 R12: 0000000000000000 R13: 00007ffe9f1a86b0 R14: 0000000000000000 R15: 0000000000000000 </TASK> Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> CC: <stable@vger.kernel.org> # 6.13+ Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>

Commit 7da55c2 ("drm/amd/display: Remove incorrect FP context start") removes the FP context protection of dml2_create(), and it said "All the DC_FP_START/END should be used before call anything from DML2". However, dml2_validate()/dml21_validate() are not protected from their callers, causing such errors: do_fpu invoked from kernel context![#1]: CPU: 10 UID: 0 PID: 331 Comm: kworker/10:1H Not tainted 6.14.0-rc6+ #4 Workqueue: events_highpri dm_irq_work_func [amdgpu] pc ffff800003191eb0 ra ffff800003191e60 tp 9000000107a94000 sp 9000000107a975b0 a0 9000000140ce4910 a1 0000000000000000 a2 9000000140ce49b0 a3 9000000140ce49a8 a4 9000000140ce49a8 a5 0000000100000000 a6 0000000000000001 a7 9000000107a97660 t0 ffff800003790000 t1 9000000140ce5000 t2 0000000000000001 t3 0000000000000000 t4 0000000000000004 t5 0000000000000000 t6 0000000000000000 t7 0000000000000000 t8 0000000100000000 u0 ffff8000031a3b9c s9 9000000130bc0000 s0 9000000132400000 s1 9000000140ec0000 s2 9000000132400000 s3 9000000140ce0000 s4 90000000057f8b88 s5 9000000140ec0000 s6 9000000140ce4910 s7 0000000000000001 s8 9000000130d45010 ra: ffff800003191e60 dml21_map_dc_state_into_dml_display_cfg+0x40/0x1140 [amdgpu] ERA: ffff800003191eb0 dml21_map_dc_state_into_dml_display_cfg+0x90/0x1140 [amdgpu] CRMD: 000000b0 (PLV0 -IE -DA +PG DACF=CC DACM=CC -WE) PRMD: 00000004 (PPLV0 +PIE -PWE) EUEN: 00000000 (-FPE -SXE -ASXE -BTE) ECFG: 00071c1d (LIE=0,2-4,10-12 VS=7) ESTAT: 000f0000 [FPD] (IS= ECode=15 EsubCode=0) PRID: 0014d010 (Loongson-64bit, Loongson-3C6000/S) Process kworker/10:1H (pid: 331, threadinfo=000000007bf9ddb0, task=00000000cc4ab9f3) Stack : 0000000100000000 0000043800000780 0000000100000001 0000000100000001 0000000000000000 0000078000000000 0000000000000438 0000078000000000 0000000000000438 0000078000000000 0000000000000438 0000000100000000 0000000100000000 0000000100000000 0000000100000000 0000000100000000 0000000000000001 9000000140ec0000 9000000132400000 9000000132400000 ffff800003408000 ffff800003408000 9000000132400000 9000000140ce0000 9000000140ce0000 ffff800003193850 0000000000000001 9000000140ec0000 9000000132400000 9000000140ec0860 9000000140ec0738 0000000000000001 90000001405e8000 9000000130bc0000 9000000140ec02a8 ffff8000031b5db8 0000000000000000 0000043800000780 0000000000000003 ffff8000031b79cc ... Call Trace: [<ffff800003191eb0>] dml21_map_dc_state_into_dml_display_cfg+0x90/0x1140 [amdgpu] [<ffff80000319384c>] dml21_validate+0xcc/0x520 [amdgpu] [<ffff8000031b8948>] dc_validate_global_state+0x2e8/0x460 [amdgpu] [<ffff800002e94034>] create_validate_stream_for_sink+0x3d4/0x420 [amdgpu] [<ffff800002e940e4>] amdgpu_dm_connector_mode_valid+0x64/0x240 [amdgpu] [<900000000441d6b8>] drm_connector_mode_valid+0x38/0x80 [<900000000441d824>] __drm_helper_update_and_validate+0x124/0x3e0 [<900000000441ddc0>] drm_helper_probe_single_connector_modes+0x2e0/0x620 [<90000000044050dc>] drm_client_modeset_probe+0x23c/0x1780 [<9000000004420384>] __drm_fb_helper_initial_config_and_unlock+0x44/0x5a0 [<9000000004403acc>] drm_client_dev_hotplug+0xcc/0x140 [<ffff800002e9ab50>] handle_hpd_irq_helper+0x1b0/0x1e0 [amdgpu] [<90000000038f5da0>] process_one_work+0x160/0x300 [<90000000038f6718>] worker_thread+0x318/0x440 [<9000000003901b8c>] kthread+0x12c/0x220 [<90000000038b1484>] ret_from_kernel_thread+0x8/0xa4 Unfortunately, protecting dml2_validate()/dml21_validate() out of DML2 causes "sleeping function called from invalid context", so protect them with DC_FP_START() and DC_FP_END() inside. Fixes: 7da55c2 ("drm/amd/display: Remove incorrect FP context start") Cc: stable@vger.kernel.org Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Tested-by: Dongyan Qian <qiandongyan@loongson.cn> Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If we finds a vq without a name in our input array in virtio_ccw_find_vqs(), we treat it as "non-existing" and set the vq pointer to NULL; we will not call virtio_ccw_setup_vq() to allocate/setup a vq. Consequently, we create only a queue if it actually exists (name != NULL) and assign an incremental queue index to each such existing queue. However, in virtio_ccw_register_adapter_ind()->get_airq_indicator() we will not ignore these "non-existing queues", but instead assign an airq indicator to them. Besides never releasing them in virtio_ccw_drop_indicators() (because there is no virtqueue), the bigger issue seems to be that there will be a disagreement between the device and the Linux guest about the airq indicator to be used for notifying a queue, because the indicator bit for adapter I/O interrupt is derived from the queue index. The virtio spec states under "Setting Up Two-Stage Queue Indicators": ... indicator contains the guest address of an area wherein the indicators for the devices are contained, starting at bit_nr, one bit per virtqueue of the device. And further in "Notification via Adapter I/O Interrupts": For notifying the driver of virtqueue buffers, the device sets the bit in the guest-provided indicator area at the corresponding offset. For example, QEMU uses in virtio_ccw_notify() the queue index (passed as "vector") to select the relevant indicator bit. If a queue does not exist, it does not have a corresponding indicator bit assigned, because it effectively doesn't have a queue index. Using a virtio-balloon-ccw device under QEMU with free-page-hinting disabled ("free-page-hint=off") but free-page-reporting enabled ("free-page-reporting=on") will result in free page reporting not working as expected: in the virtio_balloon driver, we'll be stuck forever in virtballoon_free_page_report()->wait_event(), because the waitqueue will not be woken up as the notification from the device is lost: it would use the wrong indicator bit. Free page reporting stops working and we get splats (when configured to detect hung wqs) like: INFO: task kworker/1:3:463 blocked for more than 61 seconds. Not tainted 6.14.0 #4 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. task:kworker/1:3 [...] Workqueue: events page_reporting_process Call Trace: [<000002f404e6dfb2>] __schedule+0x402/0x1640 [<000002f404e6f22e>] schedule+0x3e/0xe0 [<000002f3846a88fa>] virtballoon_free_page_report+0xaa/0x110 [virtio_balloon] [<000002f40435c8a4>] page_reporting_process+0x2e4/0x740 [<000002f403fd3ee2>] process_one_work+0x1c2/0x400 [<000002f403fd4b96>] worker_thread+0x296/0x420 [<000002f403fe10b4>] kthread+0x124/0x290 [<000002f403f4e0dc>] __ret_from_fork+0x3c/0x60 [<000002f404e77272>] ret_from_fork+0xa/0x38 There was recently a discussion [1] whether the "holes" should be treated differently again, effectively assigning also non-existing queues a queue index: that should also fix the issue, but requires other workarounds to not break existing setups. Let's fix it without affecting existing setups for now by properly ignoring the non-existing queues, so the indicator bits will match the queue indexes. [1] https://lore.kernel.org/all/cover.1720611677.git.mst@redhat.com/ Fixes: a229989 ("virtio: don't allocate vqs when names[i] = NULL") Reported-by: Chandra Merla <cmerla@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: David Hildenbrand <david@redhat.com> Tested-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com> Link: https://lore.kernel.org/r/20250402203621.940090-1-david@redhat.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com>

There is a potential deadlock if we do report zones in an IO context, detailed in below lockdep report. When one process do a report zones and another process freezes the block device, the report zones side cannot allocate a tag because the freeze is already started. This can thus result in new block group creation to hang forever, blocking the write path. Thankfully, a new block group should be created on empty zones. So, reporting the zones is not necessary and we can set the write pointer = 0 and load the zone capacity from the block layer using bdev_zone_capacity() helper. ====================================================== WARNING: possible circular locking dependency detected 6.14.0-rc1 #252 Not tainted ------------------------------------------------------ modprobe/1110 is trying to acquire lock: ffff888100ac83e0 ((work_completion)(&(&wb->dwork)->work)){+.+.}-{0:0}, at: __flush_work+0x38f/0xb60 but task is already holding lock: ffff8881205b6f20 (&q->q_usage_counter(queue)#16){++++}-{0:0}, at: sd_remove+0x85/0x130 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (&q->q_usage_counter(queue)#16){++++}-{0:0}: blk_queue_enter+0x3d9/0x500 blk_mq_alloc_request+0x47d/0x8e0 scsi_execute_cmd+0x14f/0xb80 sd_zbc_do_report_zones+0x1c1/0x470 sd_zbc_report_zones+0x362/0xd60 blkdev_report_zones+0x1b1/0x2e0 btrfs_get_dev_zones+0x215/0x7e0 [btrfs] btrfs_load_block_group_zone_info+0x6d2/0x2c10 [btrfs] btrfs_make_block_group+0x36b/0x870 [btrfs] btrfs_create_chunk+0x147d/0x2320 [btrfs] btrfs_chunk_alloc+0x2ce/0xcf0 [btrfs] start_transaction+0xce6/0x1620 [btrfs] btrfs_uuid_scan_kthread+0x4ee/0x5b0 [btrfs] kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #2 (&fs_info->dev_replace.rwsem){++++}-{4:4}: down_read+0x9b/0x470 btrfs_map_block+0x2ce/0x2ce0 [btrfs] btrfs_submit_chunk+0x2d4/0x16c0 [btrfs] btrfs_submit_bbio+0x16/0x30 [btrfs] btree_write_cache_pages+0xb5a/0xf90 [btrfs] do_writepages+0x17f/0x7b0 __writeback_single_inode+0x114/0xb00 writeback_sb_inodes+0x52b/0xe00 wb_writeback+0x1a7/0x800 wb_workfn+0x12a/0xbd0 process_one_work+0x85a/0x1460 worker_thread+0x5e2/0xfc0 kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #1 (&fs_info->zoned_meta_io_lock){+.+.}-{4:4}: __mutex_lock+0x1aa/0x1360 btree_write_cache_pages+0x252/0xf90 [btrfs] do_writepages+0x17f/0x7b0 __writeback_single_inode+0x114/0xb00 writeback_sb_inodes+0x52b/0xe00 wb_writeback+0x1a7/0x800 wb_workfn+0x12a/0xbd0 process_one_work+0x85a/0x1460 worker_thread+0x5e2/0xfc0 kthread+0x39d/0x750 ret_from_fork+0x30/0x70 ret_from_fork_asm+0x1a/0x30 -> #0 ((work_completion)(&(&wb->dwork)->work)){+.+.}-{0:0}: __lock_acquire+0x2f52/0x5ea0 lock_acquire+0x1b1/0x540 __flush_work+0x3ac/0xb60 wb_shutdown+0x15b/0x1f0 bdi_unregister+0x172/0x5b0 del_gendisk+0x841/0xa20 sd_remove+0x85/0x130 device_release_driver_internal+0x368/0x520 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 __scsi_remove_device+0x272/0x340 scsi_forget_host+0xf7/0x170 scsi_remove_host+0xd2/0x2a0 sdebug_driver_remove+0x52/0x2f0 [scsi_debug] device_release_driver_internal+0x368/0x520 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 device_unregister+0x13/0xa0 sdebug_do_remove_host+0x1fb/0x290 [scsi_debug] scsi_debug_exit+0x17/0x70 [scsi_debug] __do_sys_delete_module.isra.0+0x321/0x520 do_syscall_64+0x93/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e other info that might help us debug this: Chain exists of: (work_completion)(&(&wb->dwork)->work) --> &fs_info->dev_replace.rwsem --> &q->q_usage_counter(queue)#16 Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&q->q_usage_counter(queue)#16); lock(&fs_info->dev_replace.rwsem); lock(&q->q_usage_counter(queue)#16); lock((work_completion)(&(&wb->dwork)->work)); *** DEADLOCK *** 5 locks held by modprobe/1110: #0: ffff88811f7bc108 (&dev->mutex){....}-{4:4}, at: device_release_driver_internal+0x8f/0x520 #1: ffff8881022ee0e0 (&shost->scan_mutex){+.+.}-{4:4}, at: scsi_remove_host+0x20/0x2a0 #2: ffff88811b4c4378 (&dev->mutex){....}-{4:4}, at: device_release_driver_internal+0x8f/0x520 #3: ffff8881205b6f20 (&q->q_usage_counter(queue)#16){++++}-{0:0}, at: sd_remove+0x85/0x130 #4: ffffffffa3284360 (rcu_read_lock){....}-{1:3}, at: __flush_work+0xda/0xb60 stack backtrace: CPU: 0 UID: 0 PID: 1110 Comm: modprobe Not tainted 6.14.0-rc1 #252 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-3.fc41 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x6a/0x90 print_circular_bug.cold+0x1e0/0x274 check_noncircular+0x306/0x3f0 ? __pfx_check_noncircular+0x10/0x10 ? mark_lock+0xf5/0x1650 ? __pfx_check_irq_usage+0x10/0x10 ? lockdep_lock+0xca/0x1c0 ? __pfx_lockdep_lock+0x10/0x10 __lock_acquire+0x2f52/0x5ea0 ? __pfx___lock_acquire+0x10/0x10 ? __pfx_mark_lock+0x10/0x10 lock_acquire+0x1b1/0x540 ? __flush_work+0x38f/0xb60 ? __pfx_lock_acquire+0x10/0x10 ? __pfx_lock_release+0x10/0x10 ? mark_held_locks+0x94/0xe0 ? __flush_work+0x38f/0xb60 __flush_work+0x3ac/0xb60 ? __flush_work+0x38f/0xb60 ? __pfx_mark_lock+0x10/0x10 ? __pfx___flush_work+0x10/0x10 ? __pfx_wq_barrier_func+0x10/0x10 ? __pfx___might_resched+0x10/0x10 ? mark_held_locks+0x94/0xe0 wb_shutdown+0x15b/0x1f0 bdi_unregister+0x172/0x5b0 ? __pfx_bdi_unregister+0x10/0x10 ? up_write+0x1ba/0x510 del_gendisk+0x841/0xa20 ? __pfx_del_gendisk+0x10/0x10 ? _raw_spin_unlock_irqrestore+0x35/0x60 ? __pm_runtime_resume+0x79/0x110 sd_remove+0x85/0x130 device_release_driver_internal+0x368/0x520 ? kobject_put+0x5d/0x4a0 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 ? __pfx_device_del+0x10/0x10 __scsi_remove_device+0x272/0x340 scsi_forget_host+0xf7/0x170 scsi_remove_host+0xd2/0x2a0 sdebug_driver_remove+0x52/0x2f0 [scsi_debug] ? kernfs_remove_by_name_ns+0xc0/0xf0 device_release_driver_internal+0x368/0x520 ? kobject_put+0x5d/0x4a0 bus_remove_device+0x1f1/0x3f0 device_del+0x3bd/0x9c0 ? __pfx_device_del+0x10/0x10 ? __pfx___mutex_unlock_slowpath+0x10/0x10 device_unregister+0x13/0xa0 sdebug_do_remove_host+0x1fb/0x290 [scsi_debug] scsi_debug_exit+0x17/0x70 [scsi_debug] __do_sys_delete_module.isra.0+0x321/0x520 ? __pfx___do_sys_delete_module.isra.0+0x10/0x10 ? __pfx_slab_free_after_rcu_debug+0x10/0x10 ? kasan_save_stack+0x2c/0x50 ? kasan_record_aux_stack+0xa3/0xb0 ? __call_rcu_common.constprop.0+0xc4/0xfb0 ? kmem_cache_free+0x3a0/0x590 ? __x64_sys_close+0x78/0xd0 do_syscall_64+0x93/0x180 ? lock_is_held_type+0xd5/0x130 ? __call_rcu_common.constprop.0+0x3c0/0xfb0 ? lockdep_hardirqs_on+0x78/0x100 ? __call_rcu_common.constprop.0+0x3c0/0xfb0 ? __pfx___call_rcu_common.constprop.0+0x10/0x10 ? kmem_cache_free+0x3a0/0x590 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 ? __pfx___x64_sys_openat+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x16d/0x400 ? do_syscall_64+0x9f/0x180 ? lockdep_hardirqs_on+0x78/0x100 ? do_syscall_64+0x9f/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7f436712b68b RSP: 002b:00007ffe9f1a8658 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0 RAX: ffffffffffffffda RBX: 00005559b367fd80 RCX: 00007f436712b68b RDX: 0000000000000000 RSI: 0000000000000800 RDI: 00005559b367fde8 RBP: 00007ffe9f1a8680 R08: 1999999999999999 R09: 0000000000000000 R10: 00007f43671a5fe0 R11: 0000000000000206 R12: 0000000000000000 R13: 00007ffe9f1a86b0 R14: 0000000000000000 R15: 0000000000000000 </TASK> Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> CC: <stable@vger.kernel.org> # 6.13+ Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>

When migrating a THP, concurrent access to the PMD migration entry during a deferred split scan can lead to an invalid address access, as illustrated below. To prevent this invalid access, it is necessary to check the PMD migration entry and return early. In this context, there is no need to use pmd_to_swp_entry and pfn_swap_entry_to_page to verify the equality of the target folio. Since the PMD migration entry is locked, it cannot be served as the target. Mailing list discussion and explanation from Hugh Dickins: "An anon_vma lookup points to a location which may contain the folio of interest, but might instead contain another folio: and weeding out those other folios is precisely what the "folio != pmd_folio((*pmd)" check (and the "risk of replacing the wrong folio" comment a few lines above it) is for." BUG: unable to handle page fault for address: ffffea60001db008 CPU: 0 UID: 0 PID: 2199114 Comm: tee Not tainted 6.14.0+ #4 NONE Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:split_huge_pmd_locked+0x3b5/0x2b60 Call Trace: <TASK> try_to_migrate_one+0x28c/0x3730 rmap_walk_anon+0x4f6/0x770 unmap_folio+0x196/0x1f0 split_huge_page_to_list_to_order+0x9f6/0x1560 deferred_split_scan+0xac5/0x12a0 shrinker_debugfs_scan_write+0x376/0x470 full_proxy_write+0x15c/0x220 vfs_write+0x2fc/0xcb0 ksys_write+0x146/0x250 do_syscall_64+0x6a/0x120 entry_SYSCALL_64_after_hwframe+0x76/0x7e The bug is found by syzkaller on an internal kernel, then confirmed on upstream. Link: https://lkml.kernel.org/r/20250421113536.3682201-1-gavinguo@igalia.com Link: https://lore.kernel.org/all/20250414072737.1698513-1-gavinguo@igalia.com/ Link: https://lore.kernel.org/all/20250418085802.2973519-1-gavinguo@igalia.com/ Fixes: 84c3fc4 ("mm: thp: check pmd migration entry in common path") Signed-off-by: Gavin Guo <gavinguo@igalia.com> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Zi Yan <ziy@nvidia.com> Reviewed-by: Gavin Shan <gshan@redhat.com> Cc: Florent Revest <revest@google.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

A warning on driver removal started occurring after commit 9dd05df ("net: warn if NAPI instance wasn't shut down"). Disable tx napi before deleting it in mt76_dma_cleanup(). WARNING: CPU: 4 PID: 18828 at net/core/dev.c:7288 __netif_napi_del_locked+0xf0/0x100 CPU: 4 UID: 0 PID: 18828 Comm: modprobe Not tainted 6.15.0-rc4 #4 PREEMPT(lazy) Hardware name: ASUS System Product Name/PRIME X670E-PRO WIFI, BIOS 3035 09/05/2024 RIP: 0010:__netif_napi_del_locked+0xf0/0x100 Call Trace: <TASK> mt76_dma_cleanup+0x54/0x2f0 [mt76] mt7921_pci_remove+0xd5/0x190 [mt7921e] pci_device_remove+0x47/0xc0 device_release_driver_internal+0x19e/0x200 driver_detach+0x48/0x90 bus_remove_driver+0x6d/0xf0 pci_unregister_driver+0x2e/0xb0 __do_sys_delete_module.isra.0+0x197/0x2e0 do_syscall_64+0x7b/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e Tested with mt7921e but the same pattern can be actually applied to other mt76 drivers calling mt76_dma_cleanup() during removal. Tx napi is enabled in their *_dma_init() functions and only toggled off and on again inside their suspend/resume/reset paths. So it should be okay to disable tx napi in such a generic way. Found by Linux Verification Center (linuxtesting.org). Fixes: 2ac515a ("mt76: mt76x02: use napi polling for tx cleanup") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Tested-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com> Link: https://patch.msgid.link/20250506115540.19045-1-pchelkin@ispras.ru Signed-off-by: Felix Fietkau <nbd@nbd.name>

…xit() scheduler's ->exit() is called with queue frozen and elevator lock is held, and wbt_enable_default() can't be called with queue frozen, otherwise the following lockdep warning is triggered: #6 (&q->rq_qos_mutex){+.+.}-{4:4}: #5 (&eq->sysfs_lock){+.+.}-{4:4}: #4 (&q->elevator_lock){+.+.}-{4:4}: #3 (&q->q_usage_counter(io)#3){++++}-{0:0}: #2 (fs_reclaim){+.+.}-{0:0}: #1 (&sb->s_type->i_mutex_key#3){+.+.}-{4:4}: #0 (&q->debugfs_mutex){+.+.}-{4:4}: Fix the issue by moving wbt_enable_default() out of bfq's exit(), and call it from elevator_change_done(). Meantime add disk->rqos_state_mutex for covering wbt state change, which matches the purpose more than ->elevator_lock. Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Nilay Shroff <nilay@linux.ibm.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20250505141805.2751237-26-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk>

ACPICA commit 1c28da2242783579d59767617121035dafba18c3 This was originally done in NetBSD: NetBSD/src@b69d1ac and is the correct alternative to the smattering of `memcpy`s I previously contributed to this repository. This also sidesteps the newly strict checks added in UBSAN: llvm/llvm-project@7926744 Before this change we see the following UBSAN stack trace in Fuchsia: #0 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e #1.2 0x000021982bc4af3c in ubsan_get_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:41 <libclang_rt.asan.so>+0x41f3c #1.1 0x000021982bc4af3c in maybe_print_stack_trace() compiler-rt/lib/ubsan/ubsan_diag.cpp:51 <libclang_rt.asan.so>+0x41f3c #1 0x000021982bc4af3c in ~scoped_report() compiler-rt/lib/ubsan/ubsan_diag.cpp:395 <libclang_rt.asan.so>+0x41f3c #2 0x000021982bc4bb6f in handletype_mismatch_impl() compiler-rt/lib/ubsan/ubsan_handlers.cpp:137 <libclang_rt.asan.so>+0x42b6f #3 0x000021982bc4b723 in __ubsan_handle_type_mismatch_v1 compiler-rt/lib/ubsan/ubsan_handlers.cpp:142 <libclang_rt.asan.so>+0x42723 #4 0x000021afcfdeca5e in acpi_rs_get_address_common(struct acpi_resource*, union aml_resource*) ../../third_party/acpica/source/components/resources/rsaddr.c:329 <platform-bus-x86.so>+0x6aca5e #5 0x000021afcfdf2089 in acpi_rs_convert_aml_to_resource(struct acpi_resource*, union aml_resource*, struct acpi_rsconvert_info*) ../../third_party/acpica/source/components/resources/rsmisc.c:355 <platform-bus-x86.so>+0x6b2089 #6 0x000021afcfded169 in acpi_rs_convert_aml_to_resources(u8*, u32, u32, u8, void**) ../../third_party/acpica/source/components/resources/rslist.c:137 <platform-bus-x86.so>+0x6ad169 #7 0x000021afcfe2d24a in acpi_ut_walk_aml_resources(struct acpi_walk_state*, u8*, acpi_size, acpi_walk_aml_callback, void**) ../../third_party/acpica/source/components/utilities/utresrc.c:237 <platform-bus-x86.so>+0x6ed24a torvalds#8 0x000021afcfde66b7 in acpi_rs_create_resource_list(union acpi_operand_object*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rscreate.c:199 <platform-bus-x86.so>+0x6a66b7 torvalds#9 0x000021afcfdf6979 in acpi_rs_get_method_data(acpi_handle, const char*, struct acpi_buffer*) ../../third_party/acpica/source/components/resources/rsutils.c:770 <platform-bus-x86.so>+0x6b6979 torvalds#10 0x000021afcfdf708f in acpi_walk_resources(acpi_handle, char*, acpi_walk_resource_callback, void*) ../../third_party/acpica/source/components/resources/rsxface.c:731 <platform-bus-x86.so>+0x6b708f torvalds#11 0x000021afcfa95dcf in acpi::acpi_impl::walk_resources(acpi::acpi_impl*, acpi_handle, const char*, acpi::Acpi::resources_callable) ../../src/devices/board/lib/acpi/acpi-impl.cc:41 <platform-bus-x86.so>+0x355dcf #12 0x000021afcfaa8278 in acpi::device_builder::gather_resources(acpi::device_builder*, acpi::Acpi*, fidl::any_arena&, acpi::Manager*, acpi::device_builder::gather_resources_callback) ../../src/devices/board/lib/acpi/device-builder.cc:84 <platform-bus-x86.so>+0x368278 #13 0x000021afcfbddb87 in acpi::Manager::configure_discovered_devices(acpi::Manager*) ../../src/devices/board/lib/acpi/manager.cc:75 <platform-bus-x86.so>+0x49db87 torvalds#14 0x000021afcf99091d in publish_acpi_devices(acpi::Manager*, zx_device_t*, zx_device_t*) ../../src/devices/board/drivers/x86/acpi-nswalk.cc:95 <platform-bus-x86.so>+0x25091d #15 0x000021afcf9c1d4e in x86::X86::do_init(x86::X86*) ../../src/devices/board/drivers/x86/x86.cc:60 <platform-bus-x86.so>+0x281d4e #16 0x000021afcf9e33ad in λ(x86::X86::ddk_init::(anon class)*) ../../src/devices/board/drivers/x86/x86.cc:77 <platform-bus-x86.so>+0x2a33ad #17 0x000021afcf9e313e in fit::internal::target<(lambda at../../src/devices/board/drivers/x86/x86.cc:76:19), false, false, std::__2::allocator<std::byte>, void>::invoke(void*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:183 <platform-bus-x86.so>+0x2a313e #18 0x000021afcfbab4c7 in fit::internal::function_base<16UL, false, void(), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <platform-bus-x86.so>+0x46b4c7 #19 0x000021afcfbab342 in fit::function_impl<16UL, false, void(), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<16UL, false, void (), std::__2::allocator<std::byte> >*) ../../sdk/lib/fit/include/lib/fit/function.h:315 <platform-bus-x86.so>+0x46b342 #20 0x000021afcfcd98c3 in async::internal::retained_task::Handler(async_dispatcher_t*, async_task_t*, zx_status_t) ../../sdk/lib/async/task.cc:24 <platform-bus-x86.so>+0x5998c3 #21 0x00002290f9924616 in λ(const driver_runtime::Dispatcher::post_task::(anon class)*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/dispatcher.cc:789 <libdriver_runtime.so>+0x10a616 #22 0x00002290f9924323 in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:788:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int>::invoke(void*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0x10a323 #23 0x00002290f9904b76 in fit::internal::function_base<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xeab76 #24 0x00002290f9904831 in fit::callback_impl<24UL, true, void(std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request>>, int), std::__2::allocator<std::byte>>::operator()(fit::callback_impl<24UL, true, void (std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, int) ../../sdk/lib/fit/include/lib/fit/function.h:471 <libdriver_runtime.so>+0xea831 #25 0x00002290f98d5adc in driver_runtime::callback_request::Call(driver_runtime::callback_request*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >, zx_status_t) ../../src/devices/bin/driver_runtime/callback_request.h:74 <libdriver_runtime.so>+0xbbadc #26 0x00002290f98e1e58 in driver_runtime::Dispatcher::dispatch_callback(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::callback_request, std::__2::default_delete<driver_runtime::callback_request> >) ../../src/devices/bin/driver_runtime/dispatcher.cc:1248 <libdriver_runtime.so>+0xc7e58 #27 0x00002290f98e4159 in driver_runtime::Dispatcher::dispatch_callbacks(driver_runtime::Dispatcher*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:1308 <libdriver_runtime.so>+0xca159 #28 0x00002290f9918414 in λ(const driver_runtime::Dispatcher::create_with_adder::(anon class)*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.cc:353 <libdriver_runtime.so>+0xfe414 #29 0x00002290f991812d in fit::internal::target<(lambda at../../src/devices/bin/driver_runtime/dispatcher.cc:351:7), true, false, std::__2::allocator<std::byte>, void, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>>::invoke(void*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:128 <libdriver_runtime.so>+0xfe12d #30 0x00002290f9906fc7 in fit::internal::function_base<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::invoke(const fit::internal::function_base<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/internal/function.h:522 <libdriver_runtime.so>+0xecfc7 #31 0x00002290f9906c66 in fit::function_impl<8UL, true, void(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter>>, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte>>::operator()(const fit::function_impl<8UL, true, void (std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>), std::__2::allocator<std::byte> >*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../sdk/lib/fit/include/lib/fit/function.h:315 <libdriver_runtime.so>+0xecc66 torvalds#32 0x00002290f98e73d9 in driver_runtime::Dispatcher::event_waiter::invoke_callback(driver_runtime::Dispatcher::event_waiter*, std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, fbl::ref_ptr<driver_runtime::Dispatcher>) ../../src/devices/bin/driver_runtime/dispatcher.h:543 <libdriver_runtime.so>+0xcd3d9 #33 0x00002290f98e700d in driver_runtime::Dispatcher::event_waiter::handle_event(std::__2::unique_ptr<driver_runtime::Dispatcher::event_waiter, std::__2::default_delete<driver_runtime::Dispatcher::event_waiter> >, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/dispatcher.cc:1442 <libdriver_runtime.so>+0xcd00d #34 0x00002290f9918983 in async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event(async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>*, async_dispatcher_t*, async::wait_base*, zx_status_t, zx_packet_signal_t const*) ../../src/devices/bin/driver_runtime/async_loop_owned_event_handler.h:59 <libdriver_runtime.so>+0xfe983 torvalds#35 0x00002290f9918b9e in async::wait_method<async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>, &async_loop_owned_event_handler<driver_runtime::Dispatcher::event_waiter>::handle_event>::call_handler(async_dispatcher_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async/include/lib/async/cpp/wait.h:201 <libdriver_runtime.so>+0xfeb9e #36 0x00002290f99bf509 in async_loop_dispatch_wait(async_loop_t*, async_wait_t*, zx_status_t, zx_packet_signal_t const*) ../../sdk/lib/async-loop/loop.c:394 <libdriver_runtime.so>+0x1a5509 #37 0x00002290f99b9958 in async_loop_run_once(async_loop_t*, zx_time_t) ../../sdk/lib/async-loop/loop.c:343 <libdriver_runtime.so>+0x19f958 #38 0x00002290f99b9247 in async_loop_run(async_loop_t*, zx_time_t, _Bool) ../../sdk/lib/async-loop/loop.c:301 <libdriver_runtime.so>+0x19f247 #39 0x00002290f99ba962 in async_loop_run_thread(void*) ../../sdk/lib/async-loop/loop.c:860 <libdriver_runtime.so>+0x1a0962 #40 0x000041afd176ef30 in start_c11(void*) ../../zircon/third_party/ulib/musl/pthread/pthread_create.c:63 <libc.so>+0x84f30 torvalds#41 0x000041afd18a448d in thread_trampoline(uintptr_t, uintptr_t) ../../zircon/system/ulib/runtime/thread.cc:100 <libc.so>+0x1ba48d Link: acpica/acpica@1c28da22 Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://patch.msgid.link/4664267.LvFx2qVVIh@rjwysocki.net Signed-off-by: Tamir Duberstein <tamird@gmail.com> [ rjw: Pick up the tag from Tamir ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Running a modified trace-cmd record --nosplice where it does a mmap of the ring buffer when '--nosplice' is set, caused the following lockdep splat: ====================================================== WARNING: possible circular locking dependency detected 6.15.0-rc7-test-00002-gfb7d03d8a82f #551 Not tainted ------------------------------------------------------ trace-cmd/1113 is trying to acquire lock: ffff888100062888 (&buffer->mutex){+.+.}-{4:4}, at: ring_buffer_map+0x11c/0xe70 but task is already holding lock: ffff888100a5f9f8 (&cpu_buffer->mapping_lock){+.+.}-{4:4}, at: ring_buffer_map+0xcf/0xe70 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #5 (&cpu_buffer->mapping_lock){+.+.}-{4:4}: __mutex_lock+0x192/0x18c0 ring_buffer_map+0xcf/0xe70 tracing_buffers_mmap+0x1c4/0x3b0 __mmap_region+0xd8d/0x1f70 do_mmap+0x9d7/0x1010 vm_mmap_pgoff+0x20b/0x390 ksys_mmap_pgoff+0x2e9/0x440 do_syscall_64+0x79/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #4 (&mm->mmap_lock){++++}-{4:4}: __might_fault+0xa5/0x110 _copy_to_user+0x22/0x80 _perf_ioctl+0x61b/0x1b70 perf_ioctl+0x62/0x90 __x64_sys_ioctl+0x134/0x190 do_syscall_64+0x79/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #3 (&cpuctx_mutex){+.+.}-{4:4}: __mutex_lock+0x192/0x18c0 perf_event_init_cpu+0x325/0x7c0 perf_event_init+0x52a/0x5b0 start_kernel+0x263/0x3e0 x86_64_start_reservations+0x24/0x30 x86_64_start_kernel+0x95/0xa0 common_startup_64+0x13e/0x141 -> #2 (pmus_lock){+.+.}-{4:4}: __mutex_lock+0x192/0x18c0 perf_event_init_cpu+0xb7/0x7c0 cpuhp_invoke_callback+0x2c0/0x1030 __cpuhp_invoke_callback_range+0xbf/0x1f0 _cpu_up+0x2e7/0x690 cpu_up+0x117/0x170 cpuhp_bringup_mask+0xd5/0x120 bringup_nonboot_cpus+0x13d/0x170 smp_init+0x2b/0xf0 kernel_init_freeable+0x441/0x6d0 kernel_init+0x1e/0x160 ret_from_fork+0x34/0x70 ret_from_fork_asm+0x1a/0x30 -> #1 (cpu_hotplug_lock){++++}-{0:0}: cpus_read_lock+0x2a/0xd0 ring_buffer_resize+0x610/0x14e0 __tracing_resize_ring_buffer.part.0+0x42/0x120 tracing_set_tracer+0x7bd/0xa80 tracing_set_trace_write+0x132/0x1e0 vfs_write+0x21c/0xe80 ksys_write+0xf9/0x1c0 do_syscall_64+0x79/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #0 (&buffer->mutex){+.+.}-{4:4}: __lock_acquire+0x1405/0x2210 lock_acquire+0x174/0x310 __mutex_lock+0x192/0x18c0 ring_buffer_map+0x11c/0xe70 tracing_buffers_mmap+0x1c4/0x3b0 __mmap_region+0xd8d/0x1f70 do_mmap+0x9d7/0x1010 vm_mmap_pgoff+0x20b/0x390 ksys_mmap_pgoff+0x2e9/0x440 do_syscall_64+0x79/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e other info that might help us debug this: Chain exists of: &buffer->mutex --> &mm->mmap_lock --> &cpu_buffer->mapping_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&cpu_buffer->mapping_lock); lock(&mm->mmap_lock); lock(&cpu_buffer->mapping_lock); lock(&buffer->mutex); *** DEADLOCK *** 2 locks held by trace-cmd/1113: #0: ffff888106b847e0 (&mm->mmap_lock){++++}-{4:4}, at: vm_mmap_pgoff+0x192/0x390 #1: ffff888100a5f9f8 (&cpu_buffer->mapping_lock){+.+.}-{4:4}, at: ring_buffer_map+0xcf/0xe70 stack backtrace: CPU: 5 UID: 0 PID: 1113 Comm: trace-cmd Not tainted 6.15.0-rc7-test-00002-gfb7d03d8a82f #551 PREEMPT Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x6e/0xa0 print_circular_bug.cold+0x178/0x1be check_noncircular+0x146/0x160 __lock_acquire+0x1405/0x2210 lock_acquire+0x174/0x310 ? ring_buffer_map+0x11c/0xe70 ? ring_buffer_map+0x11c/0xe70 ? __mutex_lock+0x169/0x18c0 __mutex_lock+0x192/0x18c0 ? ring_buffer_map+0x11c/0xe70 ? ring_buffer_map+0x11c/0xe70 ? function_trace_call+0x296/0x370 ? __pfx___mutex_lock+0x10/0x10 ? __pfx_function_trace_call+0x10/0x10 ? __pfx___mutex_lock+0x10/0x10 ? _raw_spin_unlock+0x2d/0x50 ? ring_buffer_map+0x11c/0xe70 ? ring_buffer_map+0x11c/0xe70 ? __mutex_lock+0x5/0x18c0 ring_buffer_map+0x11c/0xe70 ? do_raw_spin_lock+0x12d/0x270 ? find_held_lock+0x2b/0x80 ? _raw_spin_unlock+0x2d/0x50 ? rcu_is_watching+0x15/0xb0 ? _raw_spin_unlock+0x2d/0x50 ? trace_preempt_on+0xd0/0x110 tracing_buffers_mmap+0x1c4/0x3b0 __mmap_region+0xd8d/0x1f70 ? ring_buffer_lock_reserve+0x99/0xff0 ? __pfx___mmap_region+0x10/0x10 ? ring_buffer_lock_reserve+0x99/0xff0 ? __pfx_ring_buffer_lock_reserve+0x10/0x10 ? __pfx_ring_buffer_lock_reserve+0x10/0x10 ? bpf_lsm_mmap_addr+0x4/0x10 ? security_mmap_addr+0x46/0xd0 ? lock_is_held_type+0xd9/0x130 do_mmap+0x9d7/0x1010 ? 0xffffffffc0370095 ? __pfx_do_mmap+0x10/0x10 vm_mmap_pgoff+0x20b/0x390 ? __pfx_vm_mmap_pgoff+0x10/0x10 ? 0xffffffffc0370095 ksys_mmap_pgoff+0x2e9/0x440 do_syscall_64+0x79/0x1c0 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fb0963a7de2 Code: 00 00 00 0f 1f 44 00 00 41 f7 c1 ff 0f 00 00 75 27 55 89 cd 53 48 89 fb 48 85 ff 74 3b 41 89 ea 48 89 df b8 09 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 5b 5d c3 0f 1f 00 48 8b 05 e1 9f 0d 00 64 RSP: 002b:00007ffdcc8fb878 EFLAGS: 00000246 ORIG_RAX: 0000000000000009 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fb0963a7de2 RDX: 0000000000000001 RSI: 0000000000001000 RDI: 0000000000000000 RBP: 0000000000000001 R08: 0000000000000006 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffdcc8fbe68 R14: 00007fb096628000 R15: 00005633e01a5c90 </TASK> The issue is that cpus_read_lock() is taken within buffer->mutex. The memory mapped pages are taken with the mmap_lock held. The buffer->mutex is taken within the cpu_buffer->mapping_lock. There's quite a chain with all these locks, where the deadlock can be fixed by moving the cpus_read_lock() outside the taking of the buffer->mutex. Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Vincent Donnefort <vdonnefort@google.com> Link: https://lore.kernel.org/20250527105820.0f45d045@gandalf.local.home Fixes: 117c392 ("ring-buffer: Introducing ring-buffer mapping functions") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>

Despite the fact that several lockdep-related checks are skipped when calling trylock* versions of the locking primitives, for example mutex_trylock, each time the mutex is acquired, a held_lock is still placed onto the lockdep stack by __lock_acquire() which is called regardless of whether the trylock* or regular locking API was used. This means that if the caller successfully acquires more than MAX_LOCK_DEPTH locks of the same class, even when using mutex_trylock, lockdep will still complain that the maximum depth of the held lock stack has been reached and disable itself. For example, the following error currently occurs in the ARM version of KVM, once the code tries to lock all vCPUs of a VM configured with more than MAX_LOCK_DEPTH vCPUs, a situation that can easily happen on modern systems, where having more than 48 CPUs is common, and it's also common to run VMs that have vCPU counts approaching that number: [ 328.171264] BUG: MAX_LOCK_DEPTH too low! [ 328.175227] turning off the locking correctness validator. [ 328.180726] Please attach the output of /proc/lock_stat to the bug report [ 328.187531] depth: 48 max: 48! [ 328.190678] 48 locks held by qemu-kvm/11664: [ 328.194957] #0: ffff800086de5ba0 (&kvm->lock){+.+.}-{3:3}, at: kvm_ioctl_create_device+0x174/0x5b0 [ 328.204048] #1: ffff0800e78800b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.212521] #2: ffff07ffeee51e98 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.220991] #3: ffff0800dc7d80b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.229463] #4: ffff07ffe0c980b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.237934] #5: ffff0800a3883c78 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.246405] #6: ffff07fffbe480b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 Luckily, in all instances that require locking all vCPUs, the 'kvm->lock' is taken a priori, and that fact makes it possible to use the little known feature of lockdep, called a 'nest_lock', to avoid this warning and subsequent lockdep self-disablement. The action of 'nested lock' being provided to lockdep's lock_acquire(), causes the lockdep to detect that the top of the held lock stack contains a lock of the same class and then increment its reference counter instead of pushing a new held_lock item onto that stack. See __lock_acquire for more information. Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Message-ID: <20250512180407.659015-2-mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Use kvm_trylock_all_vcpus instead of a custom implementation when locking all vCPUs of a VM, to avoid triggering a lockdep warning, in the case in which the VM is configured to have more than MAX_LOCK_DEPTH vCPUs. This fixes the following false lockdep warning: [ 328.171264] BUG: MAX_LOCK_DEPTH too low! [ 328.175227] turning off the locking correctness validator. [ 328.180726] Please attach the output of /proc/lock_stat to the bug report [ 328.187531] depth: 48 max: 48! [ 328.190678] 48 locks held by qemu-kvm/11664: [ 328.194957] #0: ffff800086de5ba0 (&kvm->lock){+.+.}-{3:3}, at: kvm_ioctl_create_device+0x174/0x5b0 [ 328.204048] #1: ffff0800e78800b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.212521] #2: ffff07ffeee51e98 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.220991] #3: ffff0800dc7d80b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.229463] #4: ffff07ffe0c980b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.237934] #5: ffff0800a3883c78 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 [ 328.246405] #6: ffff07fffbe480b8 (&vcpu->mutex){+.+.}-{3:3}, at: lock_all_vcpus+0x16c/0x2a0 Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com> Acked-by: Marc Zyngier <maz@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Message-ID: <20250512180407.659015-6-mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

This patch enables support for DYNAMIC_FTRACE_WITH_CALL_OPS on RISC-V. This allows each ftrace callsite to provide an ftrace_ops to the common ftrace trampoline, allowing each callsite to invoke distinct tracer functions without the need to fall back to list processing or to allocate custom trampolines for each callsite. This significantly speeds up cases where multiple distinct trace functions are used and callsites are mostly traced by a single tracer. The idea and most of the implementation is taken from the ARM64's implementation of the same feature. The idea is to place a pointer to the ftrace_ops as a literal at a fixed offset from the function entry point, which can be recovered by the common ftrace trampoline. We use -fpatchable-function-entry to reserve 8 bytes above the function entry by emitting 2 4 byte or 4 2 byte nops depending on the presence of CONFIG_RISCV_ISA_C. These 8 bytes are patched at runtime with a pointer to the associated ftrace_ops for that callsite. Functions are aligned to 8 bytes to make sure that the accesses to this literal are atomic. This approach allows for directly invoking ftrace_ops::func even for ftrace_ops which are dynamically-allocated (or part of a module), without going via ftrace_ops_list_func. We've benchamrked this with the ftrace_ops sample module on Spacemit K1 Jupiter: Without this patch: baseline (Linux rivos 6.14.0-09584-g7d06015d936c #3 SMP Sat Mar 29 +-----------------------+-----------------+----------------------------+ | Number of tracers | Total time (ns) | Per-call average time | |-----------------------+-----------------+----------------------------| | Relevant | Irrelevant | 100000 calls | Total (ns) | Overhead (ns) | |----------+------------+-----------------+------------+---------------| | 0 | 0 | 1357958 | 13 | - | | 0 | 1 | 1302375 | 13 | - | | 0 | 2 | 1302375 | 13 | - | | 0 | 10 | 1379084 | 13 | - | | 0 | 100 | 1302458 | 13 | - | | 0 | 200 | 1302333 | 13 | - | |----------+------------+-----------------+------------+---------------| | 1 | 0 | 13677833 | 136 | 123 | | 1 | 1 | 18500916 | 185 | 172 | | 1 | 2 | 2285645 | 228 | 215 | | 1 | 10 | 58824709 | 588 | 575 | | 1 | 100 | 505141584 | 5051 | 5038 | | 1 | 200 | 1580473126 | 15804 | 15791 | |----------+------------+-----------------+------------+---------------| | 1 | 0 | 13561000 | 135 | 122 | | 2 | 0 | 19707292 | 197 | 184 | | 10 | 0 | 67774750 | 677 | 664 | | 100 | 0 | 714123125 | 7141 | 7128 | | 200 | 0 | 1918065668 | 19180 | 19167 | +----------+------------+-----------------+------------+---------------+ Note: per-call overhead is estimated relative to the baseline case with 0 relevant tracers and 0 irrelevant tracers. With this patch: v4-rc4 (Linux rivos 6.14.0-09598-gd75747611c93 #4 SMP Sat Mar 29 +-----------------------+-----------------+----------------------------+ | Number of tracers | Total time (ns) | Per-call average time | |-----------------------+-----------------+----------------------------| | Relevant | Irrelevant | 100000 calls | Total (ns) | Overhead (ns) | |----------+------------+-----------------+------------+---------------| | 0 | 0 | 1459917 | 14 | - | | 0 | 1 | 1408000 | 14 | - | | 0 | 2 | 1383792 | 13 | - | | 0 | 10 | 1430709 | 14 | - | | 0 | 100 | 1383791 | 13 | - | | 0 | 200 | 1383750 | 13 | - | |----------+------------+-----------------+------------+---------------| | 1 | 0 | 5238041 | 52 | 38 | | 1 | 1 | 5228542 | 52 | 38 | | 1 | 2 | 5325917 | 53 | 40 | | 1 | 10 | 5299667 | 52 | 38 | | 1 | 100 | 5245250 | 52 | 39 | | 1 | 200 | 5238459 | 52 | 39 | |----------+------------+-----------------+------------+---------------| | 1 | 0 | 5239083 | 52 | 38 | | 2 | 0 | 19449417 | 194 | 181 | | 10 | 0 | 67718584 | 677 | 663 | | 100 | 0 | 709840708 | 7098 | 7085 | | 200 | 0 | 2203580626 | 22035 | 22022 | +----------+------------+-----------------+------------+---------------+ Note: per-call overhead is estimated relative to the baseline case with 0 relevant tracers and 0 irrelevant tracers. As can be seen from the above: a) Whenever there is a single relevant tracer function associated with a tracee, the overhead of invoking the tracer is constant, and does not scale with the number of tracers which are *not* associated with that tracee. b) The overhead for a single relevant tracer has dropped to ~1/3 of the overhead prior to this series (from 122ns to 38ns). This is largely due to permitting calls to dynamically-allocated ftrace_ops without going through ftrace_ops_list_func. Signed-off-by: Puranjay Mohan <puranjay12@gmail.com> [update kconfig, asm, refactor] Signed-off-by: Andy Chiu <andybnac@gmail.com> Tested-by: Björn Töpel <bjorn@rivosinc.com> Link: https://lore.kernel.org/r/20250407180838.42877-10-andybnac@gmail.com Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>

Liu Bo added 14 commits July 27, 2017 15:10

Btrfs: raid56: add raid56 log via add_dev v2 ioctl

04d259d

This introduces add_dev_v2 ioctl to add a device as raid56 journal device. With the help of a journal device, raid56 is able to to get rid of potential write holes. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Btrfs: raid56: do not allocate chunk on raid56 log

6725b39

The journal device (aka raid56 log) is not for chunk allocation, lets skip it. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Btrfs: raid56: detect raid56 log on mount

2c6f8c6

We've put the flag BTRFS_DEV_RAID56_LOG in device->type, so we can recognize the journal device of raid56 while reading the chunk tree. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Btrfs: raid56: add verbose debug

c96a72d

Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Btrfs: raid56: add readahead for recovery

a5fbff0

While doing recovery, blocks are read from the raid5/6 disk one by one, so this is adding readahead so that we can read at most 256 contiguous blocks in one read IO. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Btrfs: raid56: use the readahead helper to get page

0ef4bbe

This updates recovery code to use the readahead helper. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

Btrfs: raid56: initialize raid5/6 log after adding it

9b7a565

We need to initialize the raid5/6 log after adding it, but we don't want to race with concurrent writes. So we initialize it before assigning the log pointer in %fs_info. Signed-off-by: Liu Bo <bo.li.liu@oracle.com>

kdave closed this Aug 20, 2020

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Uh oh!

V4.12 rc3 r5log rebase #4

V4.12 rc3 r5log rebase #4

Uh oh!

liubogithub commented Aug 3, 2017

Uh oh!

Uh oh!

V4.12 rc3 r5log rebase #4

V4.12 rc3 r5log rebase #4

Uh oh!

Conversation

liubogithub commented Aug 3, 2017

Uh oh!

Uh oh!