printer-max3_probe.cfg

#MAX3
#V4.3.11
# This file contains common pin mappings for MKS SKIPR
# boards. To use this config, the firmware should be compiled for the
# stm32f407. When running "make menuconfig", select the 48KiB
# bootloader, and enable "Serial for communication" and select the "on USART1 PA10/PA9"

# The "make flash" command does not work on the MKS SKIPR. Instead,
# after running "make", copy the generated "out/klipper.bin" file to a
# file named "mks_skipr.bin" on an SD card and then restart the
# MKS SKIPR with that SD card.
# This file contains common pin mappings for MKS SKIPR
# boards. To use this config, the firmware should be compiled for the
# stm32f407. When running "make menuconfig", select the 48KiB
# bootloader, and enable "Serial for communication" and select the "on USART1 PA10/PA9"

# The "make flash" command does not work on the MKS SKIPR. Instead,
# after running "make", copy the generated "out/klipper.bin" file to a
# file named "mks_skipr.bin" on an SD card and then restart the
# MKS SKIPR with that SD card.

# See docs/Config_Reference.md for a description of parameters.
[include MKS_THR.cfg]
[include Adaptive_Mesh.cfg]
[mcu]
# The hardware use USART1 PA10/PA9 connect to RK3328
#serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_4D0045001850314335393520-if00
serial: /dev/ttyS0
restart_method: command


#[mcu MKS_THR]
#serial:/dev/serial/by-id/usb-Klipper_rp2040_D5CE4D9543D14858-if00

#canbus_uuid: 11aa22bb33cc
#####################################################################
#   冷却风扇
#####################################################################




[extruder]
step_pin: MKS_THR:gpio5
dir_pin: MKS_THR:gpio4
enable_pin: !MKS_THR:gpio10
rotation_distance: 53.5  #22.6789511	#Bondtech 5mm Drive Gears
gear_ratio: 1628:170				
microsteps: 16
full_steps_per_rotation: 200	#200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.400
filament_diameter: 1.75
min_temp: 0
max_temp: 360
min_extrude_temp: 170
smooth_time: 0.000001


heater_pin: MKS_THR:gpio0
sensor_type:MAX6675
#   One of "MAX6675", "MAX31855", "MAX31856", or "MAX31865".
#   One of "MAX6675", "MAX31855", "MAX31856", or "MAX31865".
sensor_pin:MKS_THR:gpio17
#   The chip select line for the sensor chip. This parameter must be
#   provided.
spi_speed: 100000
#   The SPI speed (in hz) to use when communicating with the chip.
#   The default is 4000000.
#spi_bus:spi1
spi_software_sclk_pin:MKS_THR:gpio18
spi_software_mosi_pin:MKS_THR:gpio19
spi_software_miso_pin:MKS_THR:gpio16
#   See the "common SPI settings" section for a description of the
#   above parameters.
#tc_type: K
#tc_use_50Hz_filter: False
#c_averaging_count: 1
#   The above parameters control the sensor parameters of MAX31856
#   chips. The defaults for each parameter are next to the parameter
#   name in the above list.
max_power: 1.0
control : pid  
pid_Kp=14.734
pid_Ki=6.549 
pid_Kd=8.288

pressure_advance: 0.032
pressure_advance_smooth_time: 0.03
max_extrude_cross_section:500
instantaneous_corner_velocity: 10.000
max_extrude_only_distance: 120.0
max_extrude_only_velocity:5000
max_extrude_only_accel:2000
step_pulse_duration:0.000002


[tmc2209 extruder]
uart_pin: MKS_THR:gpio6
interpolate: True
run_current: 0.714
#hold_current: 0.5
#sense_resistor: 0.110
stealthchop_threshold: 0


[adxl345]
cs_pin: MKS_THR:gpio13
spi_software_sclk_pin: MKS_THR:gpio14
spi_software_mosi_pin: MKS_THR:gpio15
spi_software_miso_pin: MKS_THR:gpio12
axes_map: -x, z, -y



[printer]
kinematics:corexy
max_velocity: 600
max_accel: 20000
max_accel_to_decel: 10000
max_z_velocity: 20
max_z_accel: 500
square_corner_velocity: 8

##移动配置============================================================================================================

[force_move]
enable_force_move : True

[gcode_macro M84]
rename_existing:M84.1
gcode:
	SET_STEPPER_ENABLE STEPPER=stepper_x enable=0
	SET_STEPPER_ENABLE STEPPER=stepper_y enable=0
	SET_STEPPER_ENABLE STEPPER=stepper_z enable=0
	SET_STEPPER_ENABLE STEPPER=extruder enable=0
	SET_KINEMATIC_POSITION
	
[delayed_gcode KINEMATIC_POSITION]
initial_duration:0.2
gcode:
    SET_KINEMATIC_POSITION X=150
    SET_KINEMATIC_POSITION Y=150
	SET_KINEMATIC_POSITION Z=150
    SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0



[stepper_x]
step_pin:PB4
dir_pin:PB3
enable_pin:!PB5
microsteps:16
rotation_distance: 39.94
full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
endstop_pin:tmc2209_stepper_x:virtual_endstop
position_min: -7
position_endstop:-7
position_max:325
homing_speed:40
homing_retract_dist:0
homing_positive_dir:False
step_pulse_duration:0.000002

[stepper_y]
step_pin:PC14
dir_pin:PC13
enable_pin:!PC15
microsteps: 16
rotation_distance: 39.94
full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
endstop_pin:tmc2209_stepper_y:virtual_endstop
position_min: -9.5
position_endstop: -9.5
position_max: 325
homing_speed:40
homing_retract_dist:0
homing_positive_dir:False
step_pulse_duration:0.000002



[stepper_z]
step_pin:PC10
dir_pin:PA15
enable_pin: !PC11
microsteps: 16
rotation_distance: 8
full_steps_per_rotation: 200
endstop_pin:probe:z_virtual_endstop#!PC3 #for Z-max; endstop have'!' is NO
#position_endstop:326
position_max:325
position_min: -6
homing_speed: 8
homing_retract_dist: 8.0
second_homing_speed: 8
homing_positive_dir:false
step_pulse_duration:0.000002

[tmc2209 stepper_x]
uart_pin: PD2
run_current:1.07
#hold_current: 0.5
interpolate: True
stealthchop_threshold: 0
diag_pin:^PB8
driver_SGTHRS: 85
#driver_SGTHRS: 130
[tmc2209 stepper_y]
uart_pin: PB9
run_current: 1.07
#hold_current: 0.5
interpolate: True
stealthchop_threshold: 0
diag_pin:^PC0
driver_SGTHRS: 85
#driver_SGTHRS: 145

#[tmc2240 stepper_y]
#cs_pin:PB9
#spi_software_sclk_pin:PA5
#spi_software_mosi_pin:PA7
#spi_software_miso_pin:PA6
#spi_speed:200000
#run_current: 1.07
#hold_current: 0.5
#sense_resistor: 0.110
#interpolate:true
#stealthchop_threshold:1
#diag0_pin:!PC0
#driver_SGT:1

#[tmc2240 stepper_x]
#cs_pin:PD2
#spi_software_sclk_pin:PA5
#spi_software_mosi_pin:PA7
#spi_software_miso_pin:PA6
#spi_speed:200000
#run_current: 1.07
#hold_current: 0.5
#sense_resistor: 0.110
#interpolate:true
#stealthchop_threshold:1
#diag0_pin:!PB8
#driver_SGT:1

[tmc2209 stepper_z]
uart_pin: PC5
run_current: 0.95
#hold_current: 0.6
interpolate: True
stealthchop_threshold: 1200

##归零流程修改
[homing_override]
set_position_X:0
set_position_y:0
set_position_z:0
axes:xy
gcode: 
    {% set HOME_CUR = 1 %}
    {% set driver_config = printer.configfile.settings['tmc2209 stepper_x'] %}
    {% set RUN_CUR = driver_config.run_current %}
    {% set HOLD_CUR = driver_config.hold_current %}

	{% if params.X is defined %}
	    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR * 0.8} 
        G28 X
		SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR}     
        BEEP I=1 DUR=100       
        G1 X10 F1200
    {% endif %}

    {% if params.Y is defined %}
		SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CUR * 0.9} 
		G28 Y
		SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CUR}   
        BEEP I=1 DUR=100          
       G1 Y10 F1200
    {% endif %}

    {% if params.Z is defined %}
#        G90
#        G1 X{printer.toolhead.axis_maximum.x/2 - printer.probe["x_offset"]} Y{printer.toolhead.axis_maximum.y/2 - printer.probe["y_offset"]} F7800
#        G91

        G28 Z
        G1 Z20 F480      
        BEEP I=1 DUR=100	  
    {% endif %}

    {% if params.X is undefined %}
    {% if params.Y is undefined %}
    {% if params.Z is undefined %}
    

    G91
#    G1 Z5 F600	
    G1 X10 F2400
    G1 Y10 F2400
    G4 P2000
    
    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR * 0.8} 
    G28 X
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR} 
    BEEP I=1 DUR=100  
    G1 X10 F1200
    
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CUR * 0.9} 
	G28 Y
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CUR} 
    BEEP I=1 DUR=100        
    
    G90
    G1 X{printer.toolhead.axis_maximum.x/2 - printer.probe["x_offset"]} Y{printer.toolhead.axis_maximum.y/2 - printer.probe["y_offset"]} F7800
    G91

    G28 Z
    BEEP I=1 DUR=100  
    G1 Z50  F480
    {% endif %}
    {% endif %}
    {% endif %}
    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR} 
    SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CUR} 
    M204 S10000

    G90
#    G1 X0 Y0 F7800

##热床热腔==================================================================================================================

[heater_bed]
heater_pin:PC8
sensor_type: NTC 100K MGB18-104F39050L32
sensor_pin: PA0
max_power: 1.0
control = pid
pid_kp = 71.039
pid_ki = 2.223
pid_kd = 567.421
min_temp: -100
max_temp: 125

[heater_generic hot]
#gcode_id:
#   使用M105查询温度时使用的ID。
#   必须提供此参数。
heater_pin:PB10
max_power:1.0
sensor_type:NTC 100K MGB18-104F39050L32
sensor_pin:PA1


control = watermark
max_delta: 1.0
#pid_Kp=63.418 
#pid_Ki=1.342 
#pid_Kd=749.125

min_temp:-100
max_temp:70

[verify_heater hot]
max_error: 300
check_gain_time:480
hysteresis: 5
heating_gain: 1



[verify_heater extruder]
max_error: 120
check_gain_time:20
hysteresis: 5
heating_gain: 1

[verify_heater heater_bed]
max_error: 200
check_gain_time:60
hysteresis: 5
heating_gain: 1


##一些引脚定义======================================

##主板上大涡轮风扇
[output_pin fan2]
pin: PA8
pwm: True
cycle_time: 0.0100
hardware_pwm: false
value: 0.00
scale: 255
shutdown_value: 0.0

##喷头喉管风扇 50度自启动
#[heater_fan my_nozzle_fan1]
#pin:PC9
#max_power:1
#shutdown_speed:1
#cycle_time:0.05
#kick_start_time:0.05
#off_below:0
#heater:extruder
#heater_temp:50.0

##活性炭吹风扇
[output_pin fan3]
pin:PC9
pwm: True
cycle_time: 0.0100
hardware_pwm: false
value: 0.0
scale: 255
shutdown_value: 0.0


## FAN0  喉管风扇
[heater_fan hotend_fan]
pin:MKS_THR:gpio1
max_power: 1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
fan_speed: 1.0
off_below: 0

[heater_fan hotend_fan2]
pin:MKS_THR:gpio20
max_power: 1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
fan_speed: 1.0
off_below: 0

[heater_fan borad_fan]
pin:PC4
max_power: 1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
fan_speed: 1.0
off_below: 0


## FAN0  吹模型风扇
[output_pin fan0]
pin: MKS_THR:gpio2
pwm: True
cycle_time: 0.0100
hardware_pwm: false
value: 0
scale: 255
shutdown_value: 0.0



##LED 灯
[output_pin caselight]
##  Chamber Lighting - In 5V-RGB Position
pin: PC7
pwm: false
shutdown_value:0
value:1
#cycle_time:0.01

[output_pin beeper]
##  Chamber Lighting - In 5V-RGB Position
pin: PA2
pwm: false
shutdown_value:0
value:0


[output_pin pwc]
pin: PA3
pwm: False
value: 1
shutdown_value: 1



##宏定义================================================================

[filament_switch_sensor fila]
pause_on_runout: True
runout_gcode:
            PAUSE
            SET_FILAMENT_SENSOR SENSOR=fila ENABLE=1
event_delay: 3.0
pause_delay: 0.5
switch_pin: !PC1

[bed_mesh]
speed:150               #调平速度
horizontal_move_z:10   #调平中Z抬高高度
mesh_min:25,10        #探测点最小位置
mesh_max:315,315      #探测点最大位置
probe_count:9,9      #调平点数
algorithm:bicubic
bicubic_tension:0.2
mesh_pps: 4, 4

#[bltouch]
#sensor_pin:^MKS_THR:gpio21
#control_pin:MKS_THR:gpio11
#stow_on_each_sample: False
[probe]
pin: ^!MKS_THR:gpio21
x_offset: 28
y_offset: 4.4
z_offset: 0.0
speed: 5
samples: 2
samples_result: average
sample_retract_dist: 3.0
samples_tolerance: 0.08
samples_tolerance_retries:3

#[gcode_macro G30]
#    G28
#    G1 X100 Y130 Z10
#    PROBE_CALIBRATE


[resonance_tester]
accel_chip:adxl345
probe_points:
    160, 160, 10  # an example

[gcode_macro SHAPER_CALIBRATE]
rename_existing: RESHAPER_CALIBRATE
gcode:
    RESHAPER_CALIBRATE FREQ_START=30 FREQ_END=150


[gcode_macro HOT_CALIBRATE_START]
variable_k: 0
gcode:
    {% if k == 0 %}
        {% if printer['heater_generic hot'].temperature > 49 %}
            SET_GCODE_VARIABLE MACRO=HOT_CALIBRATE_END VARIABLE=hot_set VALUE=1
            SET_GCODE_OFFSET Z_ADJUST=-0.10 MOVE=0
            SET_GCODE_VARIABLE MACRO=HOT_CALIBRATE_START VARIABLE=k VALUE=1
        {% endif %}
    {% endif %}

[gcode_macro HOT_CALIBRATE_END]
variable_hot_set: 0
gcode:
    {% if  hot_set == 1 %}
        SET_GCODE_VARIABLE MACRO=HOT_CALIBRATE_END VARIABLE=hot_set VALUE=0
        SET_GCODE_OFFSET Z_ADJUST=+0.10 MOVE=0
        SET_GCODE_VARIABLE MACRO=HOT_CALIBRATE_START VARIABLE=k VALUE=0
    {% endif %}

[gcode_macro PRINT_START]
gcode:
    #HOT_CALIBRATE_START

[gcode_macro PRINT_START_QD]
gcode:
    #HOT_CALIBRATE_START

[gcode_macro CANCEL_PRINT]
rename_existing: BASE_CANCEL_PRINT
gcode:
    {% if (printer.gcode_move.position.z) < 200 %}       ; check that zhop doesn't exceed z max
        G1 Z200 F600                                         
    {% endif %}

    G1  X0 Y0 F12000

    SDCARD_RESET_FILE
    PRINT_END
    BASE_CANCEL_PRINT

[gcode_macro PRINT_END]
gcode:
    M106 P2 S0
    M106 P0 S0
    M106 P3 S0  #关闭活性炭风扇
    
    M104 S0
    M140 S0
    M141 S0

    M220 S100
    M221 S100

    SET_IDLE_TIMEOUT TIMEOUT={printer.configfile.settings.idle_timeout.timeout} ; set timeout back to configured value
    CLEAR_PAUSE
    SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0

    M84
#    SET_STEPPER_ENABLE STEPPER=stepper_x enable=0
#	SET_STEPPER_ENABLE STEPPER=stepper_y enable=0
#	SET_STEPPER_ENABLE STEPPER=stepper_z enable=1
#	SET_STEPPER_ENABLE STEPPER=extruder enable=0

    BED_MESH_CLEAR      #恢复调平数据
    BED_MESH_PROFILE LOAD=default
    G31
    BEEP I=2 DUR=500



    
[gcode_macro PAUSE]
rename_existing: BASE_PAUSE
gcode:
    # Parameters
    {% set z = params.Z|default(50)|int %}                                                   ; z hop amount
    
    {% if printer['pause_resume'].is_paused|int == 0 %}     
        SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=zhop VALUE={z}                              ; set z hop variable for reference in resume macro
        SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=etemp VALUE={printer['extruder'].target}    ; set hotend temp variable for reference in resume macro
                                
#       SET_FILAMENT_SENSOR SENSOR=fila ENABLE=0                                             ; disable filament sensor       
        SAVE_GCODE_STATE NAME=PAUSE                                                          ; save current print position for resume                
        BASE_PAUSE                                                                           ; pause print
        {% if (printer.gcode_move.position.z + z) < printer.toolhead.axis_maximum.z %}       ; check that zhop doesn't exceed z max
            G91                                                                              ; relative positioning
            G1 Z{z} F600                                                                     ; raise Z up by z hop amount
        {% else %}
#            { action_respond_info("Pause zhop exceeds maximum Z height.") }                  ; if z max is exceeded, show message and set zhop value for resume to 0
            SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=zhop VALUE=0
        {% endif %}
        SAVE_GCODE_STATE NAME=PAUSEPARK2
        G90                                                                                  ; absolute positioning
        G1 X{printer.toolhead.axis_maximum.x/2} Y{printer.toolhead.axis_maximum.y} F6000   ; park toolhead at front center
        SAVE_GCODE_STATE NAME=PAUSEPARK                                                      ; save parked position in case toolhead is moved during the pause (otherwise the return zhop can error) 
        M104 S0                                                                              ; turn off hotend
        SET_IDLE_TIMEOUT TIMEOUT=86400                                                      ; set timeout to 12 hours

        SET_STEPPER_ENABLE STEPPER=extruder enable=0
    {% endif %}


[gcode_macro RESUME]
rename_existing: BASE_RESUME
variable_zhop: 0
variable_etemp: 0
gcode:
    # Parameters
    {% set e = params.E|default(2.5)|int %}                                          ; hotend prime amount (in mm)
    
    {% if printer['pause_resume'].is_paused|int == 1 %}
#        SET_FILAMENT_SENSOR SENSOR=fila ENABLE=1                          ; enable filament sensor
        #INITIAL_RGB                                                                    ; reset LCD color
        SET_IDLE_TIMEOUT TIMEOUT={printer.configfile.settings.idle_timeout.timeout}  ; set timeout back to configured value
        {% if etemp > 0 %}
            M109 S{etemp|int}                                                        ; wait for hotend to heat back up
        {% endif %}
        RESTORE_GCODE_STATE NAME=PAUSEPARK MOVE=1 MOVE_SPEED=150                     ; go back to parked position in case toolhead was moved during pause (otherwise the return zhop can error)  
        G91                                                                          ; relative positioning
        M83                                                                          ; relative extruder positioning
        {% if printer[printer.toolhead.extruder].temperature >= printer.configfile.settings.extruder.min_extrude_temp %}                                                
            G1  E{e} F900                                                ; prime nozzle by E, lower Z back down
#        {% else %}                      
#            G1 Z{zhop * -1} F900                                                     ; lower Z back down without priming (just in case we are testing the macro with cold hotend)
        {% endif %}  
        RESTORE_GCODE_STATE NAME=PAUSEPARK2 MOVE=1 MOVE_SPEED=150                           
        RESTORE_GCODE_STATE NAME=PAUSE MOVE=1 MOVE_SPEED=10                          ; restore position
        BASE_RESUME                                                                  ; resume print
    {% endif %}

[pause_resume]


[display_status]




[gcode_macro BEEP]
gcode:
    # Parameters
    {% set i = params.I|default(1)|int %}        ; Iterations (number of times to beep).
    {% set dur = params.DUR|default(100)|int %}  ; Duration/wait of each beep in ms. Default 100ms.

    {% if printer["output_pin sound"].value|int == 1 %}
        {% for iteration in range(i|int) %}
            SET_PIN PIN=beeper VALUE=1
            G4 P{dur}
            SET_PIN PIN=beeper VALUE=0
    		G4 P{dur}
        {% endfor %}
    {% endif %}




#[gcode_macro _CG28]
#gcode:
#    {% if "xyz" not in printer.toolhead.homed_axes %}
#        G28
#    {% endif %}




[gcode_macro G30]
gcode:
    BED_MESH_CLEAR      #清除调平数据
#    G28 
    BED_MESH_CALIBRATE mesh_min=10,10  mesh_max=310,310  METHOD=manual #手动动调平


[gcode_macro M141]
gcode:
    {% set s = params.S|float %}
    SET_HEATER_TEMPERATURE HEATER=hot TARGET={([s, 65]|min)}

[gcode_macro M191]
gcode:
    #Parameters
    {% set s = params.S|float %}
    
    M141 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %}  
    {% if s != 0 %}
        TEMPERATURE_WAIT SENSOR="heater_generic hot" MINIMUM={([s, 65]|min)} #MAXIMUM={s+1}   
    {% endif %}
 
    
[gcode_macro M106]
gcode:
    {% if params.P is defined %}
      {% if params.S is defined %}
        SET_PIN PIN=fan{params.P|int} VALUE={params.S|int}
      {% else %}
        SET_PIN PIN=fan{params.P|int} VALUE=255
      {% endif %}
    {% endif %} 

    {% if params.T is defined %}
        {% if (params.T|int)==-2 %}
          {% if params.S is defined %}       
            SET_PIN PIN=fan3 VALUE={params.S|int}
          {% else %}
            SET_PIN PIN=fan3 VALUE=255
          {% endif %}
        {% endif %}
    {% endif %}

    {% if params.P is undefined %}
    {% if params.T is undefined %}
    {% if params.S is defined %}
            SET_PIN PIN=fan0 VALUE={params.S|int}
       {% else %}
            SET_PIN PIN=fan0 VALUE=255       
    {% endif %}
    {% endif %}
    {% endif %}



[gcode_macro M107]
gcode:  
    SET_PIN PIN=fan0 VALUE=0 
#    SET_PIN PIN=fan1 VALUE=0
#    SET_PIN PIN=fan2 VALUE=0 

[gcode_macro M303]
gcode:
    {% if params.E is defined %}
     {% if params.S is defined %}
        {% if (params.E|int)==-1 %} 
         PID_CALIBRATE HEATER=heater_bed TARGET={params.S|int}
        {% endif %}
        {% if (params.E|int)==0 %}
         PID_CALIBRATE HEATER=extruder TARGET={params.S|int}
        {% endif %}
     {% endif %}
  {% endif %}


[gcode_macro M8029]
gcode:
     {% if params.D is defined %}
       {% if (params.D|int)==1 %} 
        SET_FILAMENT_SENSOR SENSOR=fila  ENABLE=1
       {% endif %}
       {% if (params.D|int)==0 %} 
        SET_FILAMENT_SENSOR SENSOR=fila  ENABLE=0
       {% endif %}
     {% endif %}

     
[gcode_macro M900]
gcode:
    {% if params.K is defined %} 
          SET_PRESSURE_ADVANCE ADVANCE={params.K}
    {% endif %}  
    {% if params.T is defined %}    
       SET_PRESSURE_ADVANCE SMOOTH_TIME={params.T}
    {% endif %} 


[gcode_macro M290]
gcode:
   SET_GCODE_OFFSET Z_ADJUST={params.Z}

[gcode_macro M901]
gcode:
#    M104 S140
    G28
    SHAPER_CALIBRATE
    SAVE_CONFIG



       
[gcode_macro M0]
gcode:
    PAUSE

[gcode_macro M25]
rename_existing: M9925
gcode:
    PAUSE


    
[output_pin sound]
pin: PA13
value:0


[gcode_macro beep_on]
gcode:
    SET_PIN PIN=sound VALUE=1
    
[gcode_macro beep_off]
gcode:
    SET_PIN PIN=sound VALUE=0


[gcode_arcs]
resolution: 1.0

[gcode_macro M109]
rename_existing: M99109
gcode:
    #Parameters
    {% set s = params.S|float %}
    
    M104 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %}  ; Set hotend temp
    {% if s != 0 %}
        TEMPERATURE_WAIT SENSOR=extruder MINIMUM={s} MAXIMUM={s+1}   ; Wait for hotend temp (within 1 degree)
    {% endif %}
    

[gcode_macro M4029]
gcode:
    BED_MESH_CLEAR
    G91 
    G1 Z10 F600
    G90
    G28
    G1 X{printer.toolhead.axis_maximum.x/2 - printer.probe["x_offset"]} Y{printer.toolhead.axis_maximum.y/2 - printer.probe["y_offset"]} F7800
    G1 Z15 F600
    ABORT
    PROBE_CALIBRATE
    ABORT
    G0 Z0


[gcode_macro M603]
description: filament unlode
gcode:
    G92 E0
    G0  E15 F400
    G4  P1000
    G92 E0
    G1  E-80 F800

[gcode_macro M604]
description: filament lode
gcode:
    M83
    G1  E80 F400

#####################################新增KAMP调平
[exclude_object]

[gcode_macro G31]
gcode:
    SET_GCODE_VARIABLE MACRO=G29 VARIABLE=k VALUE=1

[gcode_macro G32]
gcode:
    SET_GCODE_VARIABLE MACRO=G29 VARIABLE=k VALUE=0


[gcode_macro G29]
variable_k:1
gcode:

    {% if k|int==1 %}
        BED_MESH_CLEAR      #清除调平数据
#    G28   
        BED_MESH_CALIBRATE PROFILE=kamp  #自动调平
    {% endif %}


[gcode_macro M204]
rename_existing: M99204
gcode:
    {% if params.S is defined %}
        {% set s = params.S|float %}
    {% endif %}
    {% if params.P is defined %}
    {% if params.T is defined %}
        {% set s = [params.P|float ,params.T|float] | min %}
    {% endif %}
    {% endif %}

    SET_VELOCITY_LIMIT ACCEL={s}
    SET_VELOCITY_LIMIT ACCEL_TO_DECEL={s/2}


[idle_timeout]
timeout: 86400





#[x_twist_compensation]
#speed: 150
#   The speed (in mm/s) of non-probing moves during the calibration.
#   The default is 50.
#horizontal_move_z: 10
#   The height (in mm) that the head should be commanded to move to
#   just prior to starting a probe operation. The default is 5.
#start_x: 15
#   Defines the minimum X coordinate of the calibration
#   This should be the X coordinate that positions the nozzle at the starting
#   calibration position. This parameter must be provided.
#end_x: 260
#   Defines the maximum X coordinate of the calibration
#   This should be the X coordinate that positions the nozzle at the ending
#   calibration position. This parameter must be provided.
#y: 140
#   Defines the Y coordinate of the calibration
#   This should be the Y coordinate that positions the nozzle during the
#   calibration process. This parameter must be provided and is recommended to
#   be near the center of the bed

[gcode_macro M1029]
gcode:
#    X_TWIST_PROFILE_LOAD NAME=default
#    X_TWIST_COMPENSATE_MESH MESH_NAME=default COMPENSATION_NAME=default
#    SAVE_CONFIG

[virtual_sdcard]
#path:/home/mks/uploads
path: ~/gcode_files

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#