Start by including the library header file:
#include "Arduino_LowPowerPortentaH7.h"What you do next depends on what you want to achieve. Using only one of Deep Sleep Mode and Standby Mode might be sufficient, or you might want to combine them. If you combine them, start by enabling Deep Sleep Mode, perform any necessary work, and let the board go into Standby Mode until you need to perform more work.
The only function necessary to enable automatic Deep Sleep Mode is allowDeepSleep(). You might also find the following functions helpful: canDeepSleep(), timeSinceBoot(), timeSpentIdle(), timeSpentInSleep(), and timeSpentInDeepSleep(). Another function that can be useful when debugging Deep Sleep Locks, but not for production code, is numberOfDeepSleepLocks().
Caution
The numberOfDeepSleepLocks() function should never be used in production code because it relies on undocumented functionality in Mbed.
To use Standby Mode, you need the following functions: checkOptionBytes(), prepareOptionBytes(), standbyM7(), and standbyM4(). The option byte functions are necessary to ensure that the flash option bytes in the microcontroller are correctly set for going into Standby Mode.
Additionally, you can use wasInCPUMode() to check what the board was doing before it started:
By passing one of the modes d1DomainStandby, d2DomainStandby, standby or stop as parameter you can determine in which of these modes the CPU was before it started. It's possible that the CPU was in more than one of these modes so you need to check for each mode separately to get the complete picture.
Only if wasInCPUMode(CPUMode::standby) returns true, Standby Mode was entered correctly. The other functions can be handy for troubleshooting. Remember to clear the mode flags by calling resetPreviousCPUModeFlags() when you are done checking them.
The microcontroller has three power domains: one for the M7 core (D1), one for the M4 core (D2), and a separate third domain (D3) for some other functionality. wasInCPUMode(CPUMode::d1DomainStandby) returns true if D1 was in standby, but all three weren't at the same time, while wasInCPUMode(CPUMode::d2DomainStandby)() returns true if D2 was in standby, but all three weren't at the same time. Both functions can return true simultaneously if D1 and D2 were in standby mode while D3 was still awake. When all three domains are in standby mode simultaneously, the microcontroller as a whole enters Standby Mode automatically, and wasInCPUMode(CPUMode::standby) returns true when it wakes up again. The wasInCPUMode(CPUMode::stop) function should never return true but can be helpful for further troubleshooting if you encounter any issues with this library.
All configuration of Standby Mode is done when calling standbyM7(). It takes one or two parameters, depending on the conditions you want to set for waking up. The first parameter is one of the flags LowPowerStandbyType::untilPinActivity and LowPowerStandbyType::untilTimeElapsed. If you want to wake up from either type of event, you can combine the flags like so: LowPowerStandbyType::untilPinActivity | LowPowerStandbyType::untilTimeElapsed. If LowPowerStandbyType::untilTimeElapsed is present, the function takes a second parameter. This parameter's preferred format is 2_h + 30_min + 45_s. You can use any combination of hours, minutes, and seconds. For example, 15_h, or 1_h + 30_min, or just 90_s. If you first have to calculate the delay in your sketch, you can also pass something like this: RTCWakeupDelay(1, 20, 30). The first number is hours, the second minutes, and the third seconds. But, the preferred option is to use _h, _min, and _s since that's more explicit.
When the microcontroller wakes up again from Standby Mode, both the M7 and the M4 cores do so in parallel.
Important
You must always upload a sketch to the M4 core, in which you call standbyM4(), even if you don't intend to use the M4 core. If you don't, the microcontroller won't enter Standby Mode as a whole, even if you call standbyM7(), and that will lead to an increased power consumption.
- Standby: This example demonstrates how to enter Standby Mode for a few seconds and then wake up again. It's also possible to wake up early by pulling the GPIO 0 pin low on the Portenta Breakout Board.
- AllowDeepSleep: This example demonstrates how to enable Deep Sleep Mode.
- DeepSleepLockDebug: This example demonstrates how to debug Deep Sleep Lock problems.