diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h
index 573cfb0d3c75..fa4e0a4c3c12 100644
--- a/Marlin/src/inc/Conditionals_LCD.h
+++ b/Marlin/src/inc/Conditionals_LCD.h
@@ -70,6 +70,8 @@
   #undef FILAMENT_RUNOUT_SENSOR
   #undef FILAMENT_RUNOUT_DISTANCE_MM
   #undef DISABLE_OTHER_EXTRUDERS
+  #undef THERMAL_PROTECTION_HYSTERESIS
+  #undef THERMAL_PROTECTION_PERIOD
 #endif
 
 #define E_OPTARG(N) OPTARG(HAS_MULTI_EXTRUDER, N)
@@ -201,6 +203,10 @@
   #undef HOTEND_OFFSET_Z
 #endif
 
+//
+// Remove irrelevant Configuration.h settings
+//
+
 // Clean up E-stepper-based settings...
 #if E_STEPPERS <= 7
   #undef INVERT_E7_DIR
@@ -235,6 +241,72 @@
   #endif
 #endif
 
+// Clean up unused temperature sensors and sub-options
+
+#if !TEMP_SENSOR_0
+  #undef TEMP_SENSOR_0
+#endif
+#if !TEMP_SENSOR_1
+  #undef TEMP_SENSOR_1
+#endif
+#if !TEMP_SENSOR_2
+  #undef TEMP_SENSOR_2
+#endif
+#if !TEMP_SENSOR_3
+  #undef TEMP_SENSOR_3
+#endif
+#if !TEMP_SENSOR_4
+  #undef TEMP_SENSOR_4
+#endif
+#if !TEMP_SENSOR_5
+  #undef TEMP_SENSOR_5
+#endif
+#if !TEMP_SENSOR_6
+  #undef TEMP_SENSOR_6
+#endif
+#if !TEMP_SENSOR_7
+  #undef TEMP_SENSOR_7
+#endif
+
+#if TEMP_SENSOR_BED
+  #define HAS_HEATED_BED 1
+#else
+  #undef TEMP_SENSOR_BED
+  #undef THERMAL_PROTECTION_BED_HYSTERESIS
+  #undef THERMAL_PROTECTION_BED_PERIOD
+  #undef MAX_BED_POWER
+#endif
+#if !TEMP_SENSOR_CHAMBER
+  #undef TEMP_SENSOR_CHAMBER
+  #undef THERMAL_PROTECTION_CHAMBER_HYSTERESIS
+  #undef THERMAL_PROTECTION_CHAMBER_PERIOD
+  #undef CHAMBER_AUTO_FAN_PIN
+  #undef CHAMBER_AUTO_FAN_SPEED
+  #undef CHAMBER_AUTO_FAN_TEMPERATURE
+  #undef MAX_CHAMBER_POWER
+#endif
+#if !TEMP_SENSOR_COOLER
+  #undef TEMP_SENSOR_COOLER
+  #undef COOLER_AUTO_FAN_PIN
+  #undef COOLER_AUTO_FAN_SPEED
+  #undef COOLER_AUTO_FAN_TEMPERATURE
+#endif
+#if !TEMP_SENSOR_PROBE
+  #undef TEMP_SENSOR_PROBE
+#endif
+#if !TEMP_SENSOR_REDUNDANT
+  #undef TEMP_SENSOR_REDUNDANT
+#endif
+#if !TEMP_SENSOR_BOARD
+  #undef TEMP_SENSOR_BOARD
+#endif
+#if !TEMP_SENSOR_SOC
+  #undef TEMP_SENSOR_SOC
+#endif
+#if !SOFT_PWM_SCALE
+  #undef SOFT_PWM_SCALE
+#endif
+
 /**
  * Number of Linear Axes (e.g., XYZIJKUVW)
  * All the logical axes except for the tool (E) axis
@@ -296,12 +368,20 @@
   #endif
 #endif
 
+#if HAS_Z_AXIS
+  #ifdef Z4_DRIVER_TYPE
+    #define NUM_Z_STEPPERS 4
+  #elif defined(Z3_DRIVER_TYPE)
+    #define NUM_Z_STEPPERS 3
+  #elif defined(Z2_DRIVER_TYPE)
+    #define NUM_Z_STEPPERS 2
+  #else
+    #define NUM_Z_STEPPERS 1
+  #endif
+#endif
+
 #if !HAS_X_AXIS
   #undef AVOID_OBSTACLES
-  #undef ENDSTOPPULLUP_XMIN
-  #undef ENDSTOPPULLUP_XMAX
-  #undef X_MIN_ENDSTOP_HIT_STATE
-  #undef X_MAX_ENDSTOP_HIT_STATE
   #undef X2_DRIVER_TYPE
   #undef X_ENABLE_ON
   #undef DISABLE_X
@@ -312,14 +392,12 @@
   #undef MANUAL_X_HOME_POS
   #undef MIN_SOFTWARE_ENDSTOPS
   #undef MAX_SOFTWARE_ENDSTOPS
+  #undef MIN_SOFTWARE_ENDSTOP_X
+  #undef MAX_SOFTWARE_ENDSTOP_X
 #endif
 
 #if !HAS_Y_AXIS
   #undef AVOID_OBSTACLES
-  #undef ENDSTOPPULLUP_YMIN
-  #undef ENDSTOPPULLUP_YMAX
-  #undef Y_MIN_ENDSTOP_HIT_STATE
-  #undef Y_MAX_ENDSTOP_HIT_STATE
   #undef Y2_DRIVER_TYPE
   #undef Y_ENABLE_ON
   #undef DISABLE_Y
@@ -332,21 +410,7 @@
   #undef MAX_SOFTWARE_ENDSTOP_Y
 #endif
 
-#if HAS_Z_AXIS
-  #ifdef Z4_DRIVER_TYPE
-    #define NUM_Z_STEPPERS 4
-  #elif defined(Z3_DRIVER_TYPE)
-    #define NUM_Z_STEPPERS 3
-  #elif defined(Z2_DRIVER_TYPE)
-    #define NUM_Z_STEPPERS 2
-  #else
-    #define NUM_Z_STEPPERS 1
-  #endif
-#else
-  #undef ENDSTOPPULLUP_ZMIN
-  #undef ENDSTOPPULLUP_ZMAX
-  #undef Z_MIN_ENDSTOP_HIT_STATE
-  #undef Z_MAX_ENDSTOP_HIT_STATE
+#if !HAS_Z_AXIS
   #undef Z2_DRIVER_TYPE
   #undef Z3_DRIVER_TYPE
   #undef Z4_DRIVER_TYPE
@@ -363,10 +427,6 @@
 #endif
 
 #if !HAS_I_AXIS
-  #undef ENDSTOPPULLUP_IMIN
-  #undef ENDSTOPPULLUP_IMAX
-  #undef I_MIN_ENDSTOP_HIT_STATE
-  #undef I_MAX_ENDSTOP_HIT_STATE
   #undef I_ENABLE_ON
   #undef DISABLE_I
   #undef INVERT_I_DIR
@@ -379,10 +439,6 @@
 #endif
 
 #if !HAS_J_AXIS
-  #undef ENDSTOPPULLUP_JMIN
-  #undef ENDSTOPPULLUP_JMAX
-  #undef J_MIN_ENDSTOP_HIT_STATE
-  #undef J_MAX_ENDSTOP_HIT_STATE
   #undef J_ENABLE_ON
   #undef DISABLE_J
   #undef INVERT_J_DIR
@@ -395,10 +451,6 @@
 #endif
 
 #if !HAS_K_AXIS
-  #undef ENDSTOPPULLUP_KMIN
-  #undef ENDSTOPPULLUP_KMAX
-  #undef K_MIN_ENDSTOP_HIT_STATE
-  #undef K_MAX_ENDSTOP_HIT_STATE
   #undef K_ENABLE_ON
   #undef DISABLE_K
   #undef INVERT_K_DIR
@@ -411,10 +463,6 @@
 #endif
 
 #if !HAS_U_AXIS
-  #undef ENDSTOPPULLUP_UMIN
-  #undef ENDSTOPPULLUP_UMAX
-  #undef U_MIN_ENDSTOP_HIT_STATE
-  #undef U_MAX_ENDSTOP_HIT_STATE
   #undef U_ENABLE_ON
   #undef DISABLE_U
   #undef INVERT_U_DIR
@@ -427,10 +475,6 @@
 #endif
 
 #if !HAS_V_AXIS
-  #undef ENDSTOPPULLUP_VMIN
-  #undef ENDSTOPPULLUP_VMAX
-  #undef V_MIN_ENDSTOP_HIT_STATE
-  #undef V_MAX_ENDSTOP_HIT_STATE
   #undef V_ENABLE_ON
   #undef DISABLE_V
   #undef INVERT_V_DIR
@@ -443,10 +487,6 @@
 #endif
 
 #if !HAS_W_AXIS
-  #undef ENDSTOPPULLUP_WMIN
-  #undef ENDSTOPPULLUP_WMAX
-  #undef W_MIN_ENDSTOP_HIT_STATE
-  #undef W_MAX_ENDSTOP_HIT_STATE
   #undef W_ENABLE_ON
   #undef DISABLE_W
   #undef INVERT_W_DIR
@@ -1151,6 +1191,19 @@
   #endif
 #endif
 
+/**
+ * Unused LCD options
+ */
+#if NONE(HAS_MARLINUI_HD44780, IS_DWIN_MARLINUI, IS_TFTGLCD_PANEL) && !MB(SIMULATED)
+  #undef DISPLAY_CHARSET_HD44780
+#endif
+#if !HAS_MARLINUI_HD44780
+  #undef LCD_INFO_SCREEN_STYLE
+#endif
+#if NONE(HAS_MARLINUI_U8GLIB, HAS_TFT_LVGL_UI)
+  #undef LCD_LANGUAGE
+#endif
+
 /**
  * Disable unused SINGLENOZZLE sub-options
  */
@@ -1585,6 +1638,14 @@
   #define PROBE_SELECTED 1
 #endif
 
+#if !HAS_MESH
+  #undef MESH_INSET
+#endif
+
+#if DISABLED(ENABLE_LEVELING_FADE_HEIGHT)
+  #undef DEFAULT_LEVELING_FADE_HEIGHT
+#endif
+
 #ifdef GRID_MAX_POINTS_X
   #define GRID_MAX_POINTS ((GRID_MAX_POINTS_X) * (GRID_MAX_POINTS_Y))
   #define GRID_LOOP(A,B) for (uint8_t A = 0; A < GRID_MAX_POINTS_X; ++A) for (uint8_t B = 0; B < GRID_MAX_POINTS_Y; ++B)
diff --git a/Marlin/src/inc/Conditionals_adv.h b/Marlin/src/inc/Conditionals_adv.h
index ef0b18e4b730..3f3dcf897130 100644
--- a/Marlin/src/inc/Conditionals_adv.h
+++ b/Marlin/src/inc/Conditionals_adv.h
@@ -83,6 +83,9 @@
 
 // Convenience override for a BLTouch alone
 #if ENABLED(BLTOUCH)
+  #ifndef BLTOUCH_DELAY
+    #define BLTOUCH_DELAY 500
+  #endif
   #ifdef BLTOUCH_HS_MODE
     #define HAS_BLTOUCH_HS_MODE 1
   #endif
@@ -622,6 +625,10 @@
   #define HAS_MAX31865 1
 #endif
 
+#if !HAS_MAX_TC
+  #undef THERMOCOUPLE_MAX_ERRORS
+#endif
+
 #if TEMP_SENSOR_3 == -4
   #define TEMP_SENSOR_3_IS_AD8495 1
 #elif TEMP_SENSOR_3 == -3
@@ -819,6 +826,15 @@
   #endif
 #endif
 
+#if !ANY_THERMISTOR_IS(-1)
+  #undef TEMP_SENSOR_AD595_GAIN
+  #undef TEMP_SENSOR_AD595_OFFSET
+#endif
+#if !ANY_THERMISTOR_IS(-4)
+  #undef TEMP_SENSOR_AD8495_GAIN
+  #undef TEMP_SENSOR_AD8495_OFFSET
+#endif
+
 #if HAS_MULTI_EXTRUDER || HAS_MULTI_HOTEND || HAS_PRUSA_MMU2 || (ENABLED(MIXING_EXTRUDER) && MIXING_VIRTUAL_TOOLS > 1)
   #define HAS_TOOLCHANGE 1
 #endif
@@ -869,6 +885,10 @@
   #define HAS_PRINT_PROGRESS 1
 #endif
 
+#if !ALL(HAS_MARLINUI_MENU, HAS_MEDIA)
+  #undef SD_MENU_CONFIRM_START
+#endif
+
 #if DISABLED(SET_PROGRESS_MANUALLY)
   #undef SET_REMAINING_TIME
   #undef SET_INTERACTION_TIME
diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h
index 56d774f2fccd..9047d4831095 100644
--- a/Marlin/src/inc/Conditionals_post.h
+++ b/Marlin/src/inc/Conditionals_post.h
@@ -387,8 +387,10 @@
   #undef Z_SAFE_HOMING
 #endif
 
-#ifndef MESH_INSET
-  #define MESH_INSET 0
+#ifdef MESH_INSET
+  #define _MESH_INSET (MESH_INSET)
+#else
+  #define _MESH_INSET 0
 #endif
 
 /**
@@ -397,7 +399,7 @@
 #if ENABLED(Z_SAFE_HOMING)
   #if ENABLED(AUTO_BED_LEVELING_UBL)
     // Home close to center so grid points have z heights very close to 0
-    #define _SAFE_POINT(A) (((GRID_MAX_POINTS_##A) / 2) * (A##_BED_SIZE - 2 * (MESH_INSET)) / (GRID_MAX_POINTS_##A - 1) + MESH_INSET)
+    #define _SAFE_POINT(A) (((GRID_MAX_POINTS_##A) / 2) * (A##_BED_SIZE - 2 * _MESH_INSET) / (GRID_MAX_POINTS_##A - 1) + _MESH_INSET)
   #else
     #define _SAFE_POINT(A) A##_CENTER
   #endif
@@ -428,13 +430,6 @@
   #define MAX_AUTORETRACT 99
 #endif
 
-/**
- * Provide a DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT in case NO_VOLUMETRICS is enabled
- */
-#ifndef DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT
-  #define DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT 0.00
-#endif
-
 /**
  * LCD Contrast for Graphical Displays
  */
@@ -2350,6 +2345,138 @@
   #endif
 #endif
 
+#if !USE_X_MIN
+  #undef ENDSTOPPULLUP_XMIN
+  #undef ENDSTOPPULLDOWN_XMIN
+#endif
+#if !USE_X_MAX
+  #undef ENDSTOPPULLUP_XMAX
+  #undef ENDSTOPPULLDOWN_XMAX
+#endif
+#if !USE_Y_MIN
+  #undef ENDSTOPPULLUP_YMIN
+  #undef ENDSTOPPULLDOWN_YMIN
+#endif
+#if !USE_Y_MAX
+  #undef ENDSTOPPULLUP_YMAX
+  #undef ENDSTOPPULLDOWN_YMAX
+#endif
+#if !USE_Z_MIN
+  #undef ENDSTOPPULLUP_ZMIN
+  #undef ENDSTOPPULLDOWN_ZMIN
+#endif
+#if !USE_Z_MAX
+  #undef ENDSTOPPULLUP_ZMAX
+  #undef ENDSTOPPULLDOWN_ZMAX
+#endif
+#if !USE_I_MIN
+  #undef ENDSTOPPULLUP_IMIN
+  #undef ENDSTOPPULLDOWN_IMIN
+#endif
+#if !USE_I_MAX
+  #undef ENDSTOPPULLUP_IMAX
+  #undef ENDSTOPPULLDOWN_IMAX
+#endif
+#if !USE_J_MIN
+  #undef ENDSTOPPULLUP_JMIN
+  #undef ENDSTOPPULLDOWN_JMIN
+#endif
+#if !USE_J_MAX
+  #undef ENDSTOPPULLUP_JMAX
+  #undef ENDSTOPPULLDOWN_JMAX
+#endif
+#if !USE_K_MIN
+  #undef ENDSTOPPULLUP_KMIN
+  #undef ENDSTOPPULLDOWN_KMIN
+#endif
+#if !USE_K_MAX
+  #undef ENDSTOPPULLUP_KMAX
+  #undef ENDSTOPPULLDOWN_KMAX
+#endif
+#if !USE_U_MIN
+  #undef ENDSTOPPULLUP_UMIN
+  #undef ENDSTOPPULLDOWN_UMIN
+#endif
+#if !USE_U_MAX
+  #undef ENDSTOPPULLUP_UMAX
+  #undef ENDSTOPPULLDOWN_UMAX
+#endif
+#if !USE_V_MIN
+  #undef ENDSTOPPULLUP_VMIN
+  #undef ENDSTOPPULLDOWN_VMIN
+#endif
+#if !USE_V_MAX
+  #undef ENDSTOPPULLUP_VMAX
+  #undef ENDSTOPPULLDOWN_VMAX
+#endif
+#if !USE_W_MIN
+  #undef ENDSTOPPULLUP_WMIN
+  #undef ENDSTOPPULLDOWN_WMIN
+#endif
+#if !USE_W_MAX
+  #undef ENDSTOPPULLUP_WMAX
+  #undef ENDSTOPPULLDOWN_WMAX
+#endif
+
+#define PCAT(P) P##_PIN
+#define NEED_HIT_STATE(P) (USE_##P || (PIN_EXISTS(P##_PIN) && ((defined(X2_STOP_PIN) && X2_STOP_PIN == PCAT(P)) || (defined(Y2_STOP_PIN) && Y2_STOP_PIN == PCAT(P)) || (defined(Z2_STOP_PIN) && Z2_STOP_PIN == PCAT(P)) || (defined(Z3_STOP_PIN) && Z3_STOP_PIN == PCAT(P)) || (defined(Z4_STOP_PIN) && Z4_STOP_PIN == PCAT(P)))))
+#if !NEED_HIT_STATE(X_MIN)
+  #undef X_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(X_MAX)
+  #undef X_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(Y_MIN)
+  #undef Y_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(Y_MAX)
+  #undef Y_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(Z_MIN)
+  #undef Z_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(Z_MAX)
+  #undef Z_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(I_MIN)
+  #undef I_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(I_MAX)
+  #undef I_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(J_MIN)
+  #undef J_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(J_MAX)
+  #undef J_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(K_MIN)
+  #undef K_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(K_MAX)
+  #undef K_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(U_MIN)
+  #undef U_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(U_MAX)
+  #undef U_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(V_MIN)
+  #undef V_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(V_MAX)
+  #undef V_MAX_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(W_MIN)
+  #undef W_MIN_ENDSTOP_HIT_STATE
+#endif
+#if !NEED_HIT_STATE(W_MAX)
+  #undef W_MAX_ENDSTOP_HIT_STATE
+#endif
+#undef NEED_HIT_STATE
+#undef PCAT
+
 //
 // ADC Temp Sensors (Thermistor or Thermocouple with amplifier ADC interface)
 //
@@ -2573,8 +2700,10 @@
 #if HAS_TEMP_COOLER && PIN_EXISTS(COOLER_AUTO_FAN)
   #define HAS_AUTO_COOLER_FAN 1
 #endif
-
-#if ANY(HAS_AUTO_FAN_0, HAS_AUTO_FAN_1, HAS_AUTO_FAN_2, HAS_AUTO_FAN_3, HAS_AUTO_FAN_4, HAS_AUTO_FAN_5, HAS_AUTO_FAN_6, HAS_AUTO_FAN_7, HAS_AUTO_CHAMBER_FAN, HAS_AUTO_COOLER_FAN)
+#if ANY(HAS_AUTO_FAN_0, HAS_AUTO_FAN_1, HAS_AUTO_FAN_2, HAS_AUTO_FAN_3, HAS_AUTO_FAN_4, HAS_AUTO_FAN_5, HAS_AUTO_FAN_6, HAS_AUTO_FAN_7)
+  #define HAS_E_AUTO_FAN 1
+#endif
+#if ANY(HAS_E_AUTO_FAN, HAS_AUTO_CHAMBER_FAN, HAS_AUTO_COOLER_FAN)
   #define HAS_AUTO_FAN 1
   #define _FANOVERLAP(I,T) (T##_AUTO_FAN_PIN == E##I##_AUTO_FAN_PIN)
   #if HAS_AUTO_CHAMBER_FAN
@@ -2632,6 +2761,19 @@
   #define HAS_AUTO_REPORTING 1
 #endif
 
+#if !HAS_AUTO_CHAMBER_FAN
+  #undef CHAMBER_AUTO_FAN_SPEED
+  #undef CHAMBER_AUTO_FAN_TEMPERATURE
+#endif
+#if !HAS_AUTO_COOLER_FAN
+  #undef COOLER_AUTO_FAN_SPEED
+  #undef COOLER_AUTO_FAN_TEMPERATURE
+#endif
+#if !HAS_E_AUTO_FAN
+  #undef EXTRUDER_AUTO_FAN_SPEED
+  #undef EXTRUDER_AUTO_FAN_TEMPERATURE
+#endif
+
 #if !HAS_AUTO_CHAMBER_FAN || AUTO_CHAMBER_IS_E
   #undef AUTO_POWER_CHAMBER_FAN
 #endif
@@ -2750,6 +2892,10 @@
 
 #if PIN_EXISTS(FANMUX0)
   #define HAS_FANMUX 1  // Part Cooling fan multipliexer
+#else
+  #undef FANMUX0_PIN
+  #undef FANMUX1_PIN
+  #undef FANMUX2_PIN
 #endif
 
 /**
@@ -2855,6 +3001,8 @@
 #endif
 #if ANY(HAS_X_MS_PINS, HAS_X2_MS_PINS, HAS_Y_MS_PINS, HAS_Y2_MS_PINS, HAS_SOME_Z_MS_PINS, HAS_I_MS_PINS, HAS_J_MS_PINS, HAS_K_MS_PINS, HAS_U_MS_PINS, HAS_V_MS_PINS, HAS_W_MS_PINS, HAS_SOME_E_MS_PINS)
   #define HAS_MICROSTEPS 1
+#else
+  #undef MICROSTEP_MODES
 #endif
 
 /**
@@ -3149,10 +3297,6 @@
   #endif
 #endif
 
-#ifndef DEFAULT_LEVELING_FADE_HEIGHT
-  #define DEFAULT_LEVELING_FADE_HEIGHT 0.0
-#endif
-
 #if ENABLED(SEGMENT_LEVELED_MOVES) && !defined(LEVELED_SEGMENT_LENGTH)
   #define LEVELED_SEGMENT_LENGTH 5
 #endif
@@ -3165,16 +3309,16 @@
     // Probing points may be verified at compile time within the radius
     // using static_assert(HYPOT2(X2-X1,Y2-Y1)<=sq(PRINTABLE_RADIUS),"bad probe point!")
     // so that may be added to SanityCheck.h in the future.
-    #define _MESH_MIN_X (X_MIN_BED + (MESH_INSET))
-    #define _MESH_MIN_Y (Y_MIN_BED + (MESH_INSET))
-    #define _MESH_MAX_X (X_MAX_BED - (MESH_INSET))
-    #define _MESH_MAX_Y (Y_MAX_BED - (MESH_INSET))
+    #define _MESH_MIN_X (X_MIN_BED + _MESH_INSET)
+    #define _MESH_MIN_Y (Y_MIN_BED + _MESH_INSET)
+    #define _MESH_MAX_X (X_MAX_BED - _MESH_INSET)
+    #define _MESH_MAX_Y (Y_MAX_BED - _MESH_INSET)
   #else
     // Boundaries for Cartesian probing based on set limits
-    #define _MESH_MIN_X (_MAX(X_MIN_BED + (MESH_INSET), X_MIN_POS)) // UBL is careful not to probe off the bed. It doesn't
-    #define _MESH_MIN_Y (_MAX(Y_MIN_BED + (MESH_INSET), Y_MIN_POS)) // need NOZZLE_TO_PROBE_OFFSET in the mesh dimensions.
-    #define _MESH_MAX_X (_MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS))
-    #define _MESH_MAX_Y (_MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS))
+    #define _MESH_MIN_X (_MAX(X_MIN_BED + _MESH_INSET, X_MIN_POS)) // UBL is careful not to probe off the bed. It doesn't
+    #define _MESH_MIN_Y (_MAX(Y_MIN_BED + _MESH_INSET, Y_MIN_POS)) // need NOZZLE_TO_PROBE_OFFSET in the mesh dimensions.
+    #define _MESH_MAX_X (_MIN(X_MAX_BED - _MESH_INSET, X_MAX_POS))
+    #define _MESH_MAX_Y (_MIN(Y_MAX_BED - _MESH_INSET, Y_MAX_POS))
   #endif
 
   // These may be overridden in Configuration.h if a smaller area is desired
diff --git a/Marlin/src/lcd/extui/ia_creality/ia_creality_rts.cpp b/Marlin/src/lcd/extui/ia_creality/ia_creality_rts.cpp
index 557d4f857991..00249ff08fa8 100644
--- a/Marlin/src/lcd/extui/ia_creality/ia_creality_rts.cpp
+++ b/Marlin/src/lcd/extui/ia_creality/ia_creality_rts.cpp
@@ -1622,6 +1622,9 @@ void RTS::handleData() {
 
       float meshVal = float(recdat.data[0] - (recdat.data[0] >= 32768 ? 65536 : 0)) / 1000;
 
+      #ifndef Z_PROBE_LOW_POINT
+        #define Z_PROBE_LOW_POINT -2
+      #endif
       LIMIT(meshVal, Z_PROBE_LOW_POINT, Z_CLEARANCE_BETWEEN_PROBES);
       xy_uint8_t point = { xPnt, yPnt };
       setMeshPoint(point, meshVal);
diff --git a/Marlin/src/lcd/marlinui.cpp b/Marlin/src/lcd/marlinui.cpp
index fc21704022c5..157ef9204534 100644
--- a/Marlin/src/lcd/marlinui.cpp
+++ b/Marlin/src/lcd/marlinui.cpp
@@ -816,7 +816,7 @@ void MarlinUI::init() {
       // Add a manual move to the queue?
       if (axis == NO_AXIS_ENUM || PENDING(millis(), start_time) || planner.is_full()) return;
 
-      const feedRate_t fr_mm_s = (axis < LOGICAL_AXES) ? manual_feedrate_mm_s[axis] : XY_PROBE_FEEDRATE_MM_S;
+      const feedRate_t fr_mm_s = (axis < LOGICAL_AXES) ? manual_feedrate_mm_s[axis] : PLANNER_XY_FEEDRATE_MM_S;
 
       /**
        * For a rotational axis apply the "inch" to "mm" conversion factor. This mimics behaviour of the G-code G1
diff --git a/Marlin/src/module/motion.cpp b/Marlin/src/module/motion.cpp
index a4e69c5be7ca..7016544c2020 100644
--- a/Marlin/src/module/motion.cpp
+++ b/Marlin/src/module/motion.cpp
@@ -571,7 +571,7 @@ void do_blocking_move_to(NUM_AXIS_ARGS_(const_float_t) const_feedRate_t fr_mm_s/
     if (DEBUGGING(LEVELING)) DEBUG_XYZ("> ", NUM_AXIS_ARGS());
   #endif
 
-  const feedRate_t xy_feedrate = fr_mm_s ?: feedRate_t(XY_PROBE_FEEDRATE_MM_S);
+  const feedRate_t xy_feedrate = fr_mm_s ?: feedRate_t(PLANNER_XY_FEEDRATE_MM_S);
 
   #if HAS_Z_AXIS
     const feedRate_t z_feedrate = fr_mm_s ?: homing_feedrate(Z_AXIS);
@@ -1492,7 +1492,7 @@ float get_move_distance(const xyze_pos_t &diff OPTARG(HAS_ROTATIONAL_AXES, bool
           if (planner.buffer_line(raised, fr_zfast)) {
             //  2. Move to the current native XY and raised Z. Presumably this is a null move.
             xyze_pos_t curpos = current_position; curpos.z = raised_parked_position.z;
-            if (planner.buffer_line(curpos, PLANNER_XY_FEEDRATE())) {
+            if (planner.buffer_line(curpos, PLANNER_XY_FEEDRATE_MM_S)) {
               //  3. Lower Z back down
               line_to_current_position(fr_zfast);
             }
diff --git a/Marlin/src/module/motion.h b/Marlin/src/module/motion.h
index 3a641a6f32b9..8aa66354ac78 100644
--- a/Marlin/src/module/motion.h
+++ b/Marlin/src/module/motion.h
@@ -68,7 +68,7 @@ extern xyz_pos_t cartes;
 #elif defined(XY_PROBE_FEEDRATE)
   #define XY_PROBE_FEEDRATE_MM_S MMM_TO_MMS(XY_PROBE_FEEDRATE)
 #else
-  #define XY_PROBE_FEEDRATE_MM_S PLANNER_XY_FEEDRATE()
+  #define XY_PROBE_FEEDRATE_MM_S PLANNER_XY_FEEDRATE_MM_S
 #endif
 
 #if HAS_BED_PROBE
diff --git a/Marlin/src/module/planner.h b/Marlin/src/module/planner.h
index 1053a27688d3..88a181839efa 100644
--- a/Marlin/src/module/planner.h
+++ b/Marlin/src/module/planner.h
@@ -1114,7 +1114,13 @@ class Planner {
     #endif // HAS_JUNCTION_DEVIATION
 };
 
-#define PLANNER_XY_FEEDRATE() _MIN(planner.settings.max_feedrate_mm_s[X_AXIS], planner.settings.max_feedrate_mm_s[Y_AXIS])
+#if HAS_Y_AXIS
+  #define PLANNER_XY_FEEDRATE_MM_S _MIN(planner.settings.max_feedrate_mm_s[X_AXIS], planner.settings.max_feedrate_mm_s[Y_AXIS])
+#elif HAS_X_AXIS
+  #define PLANNER_XY_FEEDRATE_MM_S planner.settings.max_feedrate_mm_s[X_AXIS]
+#else
+  #define PLANNER_XY_FEEDRATE_MM_S 60.0f
+#endif
 
 #define ANY_AXIS_MOVES(BLOCK)  \
   (false NUM_AXIS_GANG(        \
diff --git a/Marlin/src/module/probe.h b/Marlin/src/module/probe.h
index 028a7589cc12..81b5ec6e02b6 100644
--- a/Marlin/src/module/probe.h
+++ b/Marlin/src/module/probe.h
@@ -349,8 +349,10 @@ class Probe {
   #endif
 
 private:
-  static bool probe_down_to_z(const_float_t z, const_feedRate_t fr_mm_s);
-  static float run_z_probe(const bool sanity_check=true, const_float_t z_min_point=Z_PROBE_LOW_POINT, const_float_t z_clearance=Z_TWEEN_SAFE_CLEARANCE);
+  #if HAS_BED_PROBE
+    static bool probe_down_to_z(const_float_t z, const_feedRate_t fr_mm_s);
+    static float run_z_probe(const bool sanity_check=true, const_float_t z_min_point=Z_PROBE_LOW_POINT, const_float_t z_clearance=Z_TWEEN_SAFE_CLEARANCE);
+  #endif
 };
 
 extern Probe probe;
diff --git a/Marlin/src/module/settings.cpp b/Marlin/src/module/settings.cpp
index a553d56745ad..92f08969df6e 100644
--- a/Marlin/src/module/settings.cpp
+++ b/Marlin/src/module/settings.cpp
@@ -931,7 +931,10 @@ void MarlinSettings::postprocess() {
     // Global Leveling
     //
     {
-      const float zfh = TERN(ENABLE_LEVELING_FADE_HEIGHT, planner.z_fade_height, (DEFAULT_LEVELING_FADE_HEIGHT));
+      #ifndef DEFAULT_LEVELING_FADE_HEIGHT
+        #define DEFAULT_LEVELING_FADE_HEIGHT 0
+      #endif
+      const float zfh = TERN(ENABLE_LEVELING_FADE_HEIGHT, planner.z_fade_height, DEFAULT_LEVELING_FADE_HEIGHT);
       EEPROM_WRITE(zfh);
     }
 
@@ -1320,7 +1323,7 @@ void MarlinSettings::postprocess() {
         #if ENABLED(VOLUMETRIC_EXTRUDER_LIMIT)
           EEPROM_WRITE(planner.volumetric_extruder_limit);
         #else
-          dummyf = DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT;
+          dummyf = 0.0;
           for (uint8_t q = EXTRUDERS; q--;) EEPROM_WRITE(dummyf);
         #endif
 
@@ -1330,7 +1333,7 @@ void MarlinSettings::postprocess() {
         EEPROM_WRITE(volumetric_enabled);
         dummyf = DEFAULT_NOMINAL_FILAMENT_DIA;
         for (uint8_t q = EXTRUDERS; q--;) EEPROM_WRITE(dummyf);
-        dummyf = DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT;
+        dummyf = 0.0;
         for (uint8_t q = EXTRUDERS; q--;) EEPROM_WRITE(dummyf);
 
       #endif
@@ -3311,7 +3314,7 @@ void MarlinSettings::reset() {
   //
   // Global Leveling
   //
-  TERN_(ENABLE_LEVELING_FADE_HEIGHT, new_z_fade_height = (DEFAULT_LEVELING_FADE_HEIGHT));
+  TERN_(ENABLE_LEVELING_FADE_HEIGHT, new_z_fade_height = DEFAULT_LEVELING_FADE_HEIGHT);
   TERN_(HAS_LEVELING, reset_bed_level());
 
   //
diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp
index f617d8391a88..0070fa2eeafc 100644
--- a/Marlin/src/module/temperature.cpp
+++ b/Marlin/src/module/temperature.cpp
@@ -70,6 +70,52 @@
   #include "../feature/spindle_laser.h"
 #endif
 
+#ifndef TEMP_SENSOR_0
+  #define TEMP_SENSOR_0 0
+#endif
+#ifndef TEMP_SENSOR_1
+  #define TEMP_SENSOR_1 0
+#endif
+#ifndef TEMP_SENSOR_2
+  #define TEMP_SENSOR_2 0
+#endif
+#ifndef TEMP_SENSOR_3
+  #define TEMP_SENSOR_3 0
+#endif
+#ifndef TEMP_SENSOR_4
+  #define TEMP_SENSOR_4 0
+#endif
+#ifndef TEMP_SENSOR_5
+  #define TEMP_SENSOR_5 0
+#endif
+#ifndef TEMP_SENSOR_6
+  #define TEMP_SENSOR_6 0
+#endif
+#ifndef TEMP_SENSOR_7
+  #define TEMP_SENSOR_7 0
+#endif
+#ifndef TEMP_SENSOR_BED
+  #define TEMP_SENSOR_BED 0
+#endif
+#ifndef TEMP_SENSOR_BOARD
+  #define TEMP_SENSOR_BOARD 0
+#endif
+#ifndef TEMP_SENSOR_CHAMBER
+  #define TEMP_SENSOR_CHAMBER 0
+#endif
+#ifndef TEMP_SENSOR_COOLER
+  #define TEMP_SENSOR_COOLER 0
+#endif
+#ifndef TEMP_SENSOR_PROBE
+  #define TEMP_SENSOR_PROBE 0
+#endif
+#ifndef TEMP_SENSOR_REDUNDANT
+  #define TEMP_SENSOR_REDUNDANT 0
+#endif
+#ifndef TEMP_SENSOR_SOC
+  #define TEMP_SENSOR_SOC 0
+#endif
+
 // MAX TC related macros
 #define TEMP_SENSOR_IS_MAX(n, M) (ENABLED(TEMP_SENSOR_##n##_IS_MAX##M) || (ENABLED(TEMP_SENSOR_REDUNDANT_IS_MAX##M) && REDUNDANT_TEMP_MATCH(SOURCE, E##n)))
 
diff --git a/buildroot/tests/DUE b/buildroot/tests/DUE
index 590d76606c97..3c4876b44ec8 100755
--- a/buildroot/tests/DUE
+++ b/buildroot/tests/DUE
@@ -13,6 +13,7 @@ opt_set MOTHERBOARD BOARD_RAMPS4DUE_EFB \
         GRID_MAX_POINTS_X 16 \
         E0_AUTO_FAN_PIN 8 FANMUX0_PIN 53 EXTRUDER_AUTO_FAN_SPEED 100 \
         TEMP_SENSOR_CHAMBER 3 TEMP_CHAMBER_PIN 6 HEATER_CHAMBER_PIN 45 \
+        BACKLASH_MEASUREMENT_FEEDRATE 600 \
         TRAMMING_POINT_XY '{{20,20},{20,20},{20,20},{20,20},{20,20}}' TRAMMING_POINT_NAME_5 '"Point 5"'
 opt_enable S_CURVE_ACCELERATION EEPROM_SETTINGS GCODE_MACROS \
            FIX_MOUNTED_PROBE Z_SAFE_HOMING CODEPENDENT_XY_HOMING \
diff --git a/buildroot/tests/rambo b/buildroot/tests/rambo
index a7deb02c9f55..74a1db25164f 100755
--- a/buildroot/tests/rambo
+++ b/buildroot/tests/rambo
@@ -14,8 +14,8 @@ opt_set MOTHERBOARD BOARD_RAMBO \
         EXTRUDERS 2 TEMP_SENSOR_0 -2 TEMP_SENSOR_1 1 TEMP_SENSOR_BED 2 \
         TEMP_SENSOR_PROBE 1 TEMP_PROBE_PIN 12 \
         TEMP_SENSOR_CHAMBER 3 TEMP_CHAMBER_PIN 3 HEATER_CHAMBER_PIN 45 \
-        GRID_MAX_POINTS_X 16 AUTO_POWER_E_TEMP 80 \
-        FANMUX0_PIN 53 FIL_MOTION1_PIN 45
+        GRID_MAX_POINTS_X 16 BACKLASH_MEASUREMENT_FEEDRATE 600 \
+        AUTO_POWER_E_TEMP 80 FANMUX0_PIN 53 FIL_MOTION1_PIN 45
 opt_disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN USE_WATCHDOG
 opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \
            FIX_MOUNTED_PROBE CODEPENDENT_XY_HOMING PIDTEMPBED PTC_PROBE PTC_BED \
diff --git a/buildroot/tests/teensy35 b/buildroot/tests/teensy35
index bba6859432cf..c7830aeaacf7 100755
--- a/buildroot/tests/teensy35
+++ b/buildroot/tests/teensy35
@@ -98,7 +98,7 @@ exec_test $1 $2 "Teensy 3.5/3.6 COREXY" "$3"
 # Enable COREXZ
 #
 restore_configs
-opt_set MOTHERBOARD BOARD_TEENSY35_36
+opt_set MOTHERBOARD BOARD_TEENSY35_36 BACKLASH_MEASUREMENT_FEEDRATE 600
 opt_enable COREXZ BACKLASH_COMPENSATION BACKLASH_GCODE CORE_BACKLASH
 exec_test $1 $2 "Teensy 3.5/3.6 COREXZ | BACKLASH" "$3"