-
Notifications
You must be signed in to change notification settings - Fork 2
/
Copy pathREADME.m5373evb
327 lines (291 loc) · 12.6 KB
/
README.m5373evb
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
Freescale MCF5373EVB ColdFire Development Board
================================================
TsiChung Liew(Tsi-Chung.Liew@freescale.com)
Created 11/08/07
===========================================
Changed files:
==============
- board/freescale/m5373evb/m5373evb.c Dram setup
- board/freescale/m5373evb/mii.c Mii access
- board/freescale/m5373evb/Makefile Makefile
- board/freescale/m5373evb/config.mk config make
- board/freescale/m5373evb/u-boot.lds Linker description
- arch/m68k/cpu/mcf532x/cpu.c cpu specific code
- arch/m68k/cpu/mcf532x/cpu_init.c FBCS, Mux pins, icache and RTC extra regs
- arch/m68k/cpu/mcf532x/interrupts.c cpu specific interrupt support
- arch/m68k/cpu/mcf532x/speed.c system, pci, flexbus, and cpu clock
- arch/m68k/cpu/mcf532x/Makefile Makefile
- arch/m68k/cpu/mcf532x/config.mk config make
- arch/m68k/cpu/mcf532x/start.S start up assembly code
- doc/README.m5373evb This readme file
- drivers/net/mcffec.c ColdFire common FEC driver
- drivers/serial/mcfuart.c ColdFire common UART driver
- drivers/rtc/mcfrtc.c Realtime clock Driver
- include/asm-m68k/bitops.h Bit operation function export
- include/asm-m68k/byteorder.h Byte order functions
- include/asm-m68k/fec.h FEC structure and definition
- include/asm-m68k/fsl_i2c.h I2C structure and definition
- include/asm-m68k/global_data.h Global data structure
- include/asm-m68k/immap.h ColdFire specific header file and driver macros
- include/asm-m68k/immap_532x.h mcf532x specific header file
- include/asm-m68k/io.h io functions
- include/asm-m68k/m532x.h mcf532x specific header file
- include/asm-m68k/posix_types.h Posix
- include/asm-m68k/processor.h header file
- include/asm-m68k/ptrace.h Exception structure
- include/asm-m68k/rtc.h Realtime clock header file
- include/asm-m68k/string.h String function export
- include/asm-m68k/timer.h Timer structure and definition
- include/asm-m68k/types.h Data types definition
- include/asm-m68k/uart.h Uart structure and definition
- include/asm-m68k/u-boot.h u-boot structure
- include/configs/M5373EVB.h Board specific configuration file
- arch/m68k/lib/board.c board init function
- arch/m68k/lib/cache.c
- arch/m68k/lib/interrupts Coldfire common interrupt functions
- arch/m68k/lib/m68k_linux.c
- arch/m68k/lib/time.c Timer functions (Dma timer and PIT)
- arch/m68k/lib/traps.c Exception init code
1 MCF5373 specific Options/Settings
====================================
1.1 pre-loader is no longer suppoer in thie coldfire family
1.2 Configuration settings for M5373EVB Development Board
CONFIG_MCF532x -- define for all MCF532x CPUs
CONFIG_M5373 -- define for all Freescale MCF5373 CPUs
CONFIG_M5373EVB -- define for M5373EVB board
CONFIG_MCFUART -- define to use common CF Uart driver
CONFIG_SYS_UART_PORT -- define UART port number, start with 0, 1 and 2
CONFIG_BAUDRATE -- define UART baudrate
CONFIG_MCFRTC -- define to use common CF RTC driver
CONFIG_SYS_MCFRTC_BASE -- provide base address for RTC in immap.h
CONFIG_SYS_RTC_OSCILLATOR -- define RTC clock frequency
RTC_DEBUG -- define to show RTC debug message
CONFIG_CMD_DATE -- enable to use date feature in u-boot
CONFIG_MCFFEC -- define to use common CF FEC driver
CONFIG_NET_MULTI -- define to use multi FEC in u-boot
CONFIG_MII -- enable to use MII driver
CONFIG_CF_DOMII -- enable to use MII feature in cmd_mii.c
CONFIG_SYS_DISCOVER_PHY -- enable PHY discovery
CONFIG_SYS_RX_ETH_BUFFER -- Set FEC Receive buffer
CONFIG_SYS_FAULT_ECHO_LINK_DOWN--
CONFIG_SYS_FEC0_PINMUX -- Set FEC0 Pin configuration
CONFIG_SYS_FEC0_MIIBASE -- Set FEC0 MII base register
MCFFEC_TOUT_LOOP -- set FEC timeout loop
CONFIG_MCFTMR -- define to use DMA timer
CONFIG_MCFPIT -- define to use PIT timer
CONFIG_FSL_I2C -- define to use FSL common I2C driver
CONFIG_HARD_I2C -- define for I2C hardware support
CONFIG_SOFT_I2C -- define for I2C bit-banged
CONFIG_SYS_I2C_SPEED -- define for I2C speed
CONFIG_SYS_I2C_SLAVE -- define for I2C slave address
CONFIG_SYS_I2C_OFFSET -- define for I2C base address offset
CONFIG_SYS_IMMR -- define for MBAR offset
CONFIG_SYS_MBAR -- define MBAR offset
CONFIG_MONITOR_IS_IN_RAM -- Not support
CONFIG_SYS_INIT_RAM_ADDR -- defines the base address of the MCF5373 internal SRAM
CONFIG_SYS_CSn_BASE -- defines the Chip Select Base register
CONFIG_SYS_CSn_MASK -- defines the Chip Select Mask register
CONFIG_SYS_CSn_CTRL -- defines the Chip Select Control register
CONFIG_SYS_SDRAM_BASE -- defines the DRAM Base
2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
===========================================
2.1. System memory map:
Flash: 0x00000000-0x3FFFFFFF (1024MB)
DDR: 0x40000000-0x7FFFFFFF (1024MB)
SRAM: 0x80000000-0x8FFFFFFF (256MB)
IP: 0xF0000000-0xFFFFFFFF (256MB)
2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
linux kernel, you can customize it based on your system requirements:
Flash0: 0x00000000-0x00FFFFFF (16MB)
DDR: 0x40000000-0x4FFFFFFF (256MB)
SRAM: 0x80000000-0x80007FFF (32KB)
IP: 0xFC000000-0xFC0FFFFF (64KB)
3. COMPILATION
==============
3.1 To create U-Boot the gcc-4.1-xx compiler set (ColdFire ELF or
uClinux version) from codesourcery.com was used. Download it from:
http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
3.2 Compilation
export CROSS_COMPILE=cross-compile-prefix
cd u-boot-1.x.x
make distclean
make M5373EVB_config
make
4. SCREEN DUMP
==============
4.1 M5373EVB Development board
(NOTE: May not show exactly the same)
U-Boot 1.3.0 (Nov 8 2007 - 12:44:08)
CPU: Freescale MCF5373 (Mask:65 Version:1)
CPU CLK 240 Mhz BUS CLK 80 Mhz
Board: Freescale FireEngine 5373 EVB
I2C: ready
DRAM: 32 MB
FLASH: 2 MB
In: serial
Out: serial
Err: serial
NAND: 16 MiB
Net: FEC0
-> print
bootdelay=1
baudrate=115200
ethaddr=00:e0:0c:bc:e5:60
hostname=M5373EVB
netdev=eth0
loadaddr=40010000
load=tftp ${loadaddr) ${u-boot}
upd=run load; run prog
prog=prot off 0 2ffff;era 0 2ffff;cp.b ${loadaddr} 0 ${filesize};save
ethact=FEC0
u-boot=u-boot.bin
gatewayip=192.168.1.1
netmask=255.255.255.0
ipaddr=192.168.1.3
serverip=192.168.1.2
stdin=serial
stdout=serial
stderr=serial
mem=261632k
Environment size: 401/8188 bytes
-> bdinfo
memstart = 0x40000000
memsize = 0x02000000
flashstart = 0x00000000
flashsize = 0x00200000
flashoffset = 0x00000000
sramstart = 0x80000000
sramsize = 0x00008000
mbar = 0xFC000000
busfreq = 80 MHz
ethaddr = 00:E0:0C:BC:E5:60
ip_addr = 192.168.1.3
baudrate = 115200 bps
->
-> help
? - alias for 'help'
base - print or set address offset
bdinfo - print Board Info structure
boot - boot default, i.e., run 'bootcmd'
bootd - boot default, i.e., run 'bootcmd'
bootelf - Boot from an ELF image in memory
bootm - boot application image from memory
bootp - boot image via network using BootP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
date - get/set/reset date & time
dcache - enable or disable data cache
echo - echo args to console
erase - erase FLASH memory
flinfo - print FLASH memory information
go - start application at address 'addr'
help - print online help
i2c - I2C sub-system
icache - enable or disable instruction cache
iminfo - print header information for application image
imls - list all images found in flash
itest - return true/false on integer compare
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
ls - list files in a directory (default /)
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing)
mtest - simple RAM test
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sleep - delay execution for some time
source - run script from memory
tftpboot- boot image via network using TFTP protocol
version - print monitor version
-> tftp 0x40800000 uImage
Using FEC0 device
TFTP from server 192.168.1.3; our IP address is 192.168.1.3 Filename 'uImage'.
Load address: 0x40800000
Loading: #################################################################
#################################################################
##########
done
Bytes transferred = 2053270 (1f5496 hex)
-> bootm 0x40800000
## Booting image at 40800000 ...
Image Name: Linux Kernel Image
Created: 2007-11-07 20:33:08 UTC
Image Type: M68K Linux Kernel Image (gzip compressed)
Data Size: 2053206 Bytes = 2 MB
Load Address: 40020000
Entry Point: 40020000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.6.22-uc1 (mattw@loa) (gcc version 4.2.1 (Sourcery G++ Lite 4.2-7
uClinux/COLDFIRE(m537x)
COLDFIRE port done by Greg Ungerer, gerg@snapgear.com Flat model support (C) 1998,1999 Kenneth Albanowski, D. Jeff Dionne Built 1 zonelists. Total pages: 8128 Kernel command line: rootfstype=romfs PID hash table entries: 128 (order: 7, 512 bytes) Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory available: 28092k/32768k RAM, (1788k kernel code, 244k data) Mount-cache hash table entries: 512
NET: Registered protocol family 16
USB-MCF537x: (HOST module) EHCI device is registered
USB-MCF537x: (OTG module) EHCI device is registered
USB-MCF537x: (OTG module) UDC device is registered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler cfq registered (default)
ColdFire internal UART serial driver version 1.00 ttyS0 at 0xfc060000 (irq = 90) is a builtin ColdFire UART
ttyS1 at 0xfc064000 (irq = 91) is a builtin ColdFire UART
ttyS2 at 0xfc068000 (irq = 92) is a builtin ColdFire UART RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
nbd: registered device at major 43
usbcore: registered new interface driver ub FEC ENET Version 0.2
fec: PHY @ 0x1, ID 0x20005c90 -- DP83848
eth0: ethernet 00:e0:0c:bc:e5:60
uclinux[mtd]: RAM probe address=0x4021c22c size=0x22b000 Creating 1 MTD partitions on "RAM":
0x00000000-0x0022b000 : "ROMfs"
uclinux[mtd]: set ROMfs to be root filesystem NAND device: Manufacturer ID: 0x20, Chip ID: 0x73 (ST Micro NAND 16MiB 3,3V 8-b) Scanning device for bad blocks Creating 1 MTD partitions on "NAND 16MiB 3,3V 8-bit":
0x00000000-0x01000000 : "M53xx flash partition 1"
QSPI: spi->max_speed_hz 300000
QSPI: Baud set to 255
SPI: Coldfire master initialized
M537x - Disable UART1 when using Audio
udc: Freescale MCF53xx UDC driver version 27 October 2006 init
udc: MCF53xx USB Device is found. ID=0x5 Rev=0x41 i2c /dev entries driver
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Mounted root (romfs filesystem) readonly.
Freeing unused kernel memory: 64k freed (0x401f5000 - 0x40204000) init started: BusyBox v1.00 (2007.11.07-19:57+0000) multi-call binary?Setting e Mounting filesystems
mount: Mounting devpts on /dev/pts failed: No such device
mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory Starting syslogd and klogd Setting up networking on loopback device:
Setting up networking on eth0:
info, udhcpc (v0.9.9-pre) started
eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX.
debug, Sending discover...
debug, Sending discover...
debug, Sending select for 172.27.0.130...
info, Lease of 172.27.0.130 obtained, lease time 43200 deleting routers
route: SIOC[ADD|DEL]RT: No such process
adding dns 172.27.0.1
Starting the boa webserver:
Setting time from ntp server: ntp.cs.strath.ac.uk
ntp.cs.strath.ac.uk: Unknown host
BusyBox v1.00 (2007.11.07-19:57+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands.
#